2000 SUZUKI SWIFT belt
[x] Cancel search: beltPage 70 of 557
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-19
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION
Engine oil ––––– level, leakage
Engine coolant ––––– level, leakage
Fuel ––––– level, leakage
A / T fluid ––––– level, leakage
Air cleaner element ––––– dirt, clogging
Battery ––––– fluid level, corrosion of terminal
Water pump belt ––––– tension, damage
Throttle cable ––––– play, installation
Vacuum hoses of air intake system ––––– disconnection,
looseness, deterioration, bend
Connectors of electric wire harness ––––– disconnection, friction
Fuses ––––– burning
Parts ––––– installation, bolt ––––– looseness
Parts ––––– deformation
Other parts that can be checked visually
Also check following items at engine start, if possible
Malfunction indicator lamp
Charge warning lamp
Engine oil pressure warning lamp
Engine coolant temp. meter
Fuel level meter
Tachometer, if equipped
Abnormal air being inhaled from air intake system
Exhaust system ––––– leakage of exhaust gas, noise
Other parts that can be checked visuallySection 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 6E1
Section 8
Section 6
Section 6H
Section 8 (section 6 for pressure check)
Section 8
Section 8
Page 122 of 557
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-71
1. Throttle body
2. Fuel feed hose
GoodNo good1. Injector connector
STEPACTIONYESNO
6Check PCV valve for clogging (See Section 6E1).
Is it in good condition?Go to Step 7.Replace PCV valve.
7Check EVAP Canister Purge Valve for Closing.
1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose.
3) Check that vacuum is not felt there, when engine is
cool and running at idle. See Fig. 5.
Is vacuum felt?Check EVAP
control system
(See Section 6E1).Go to Step 8.
8Check intake manifold pressure sensor for performance
(See Section 6E1).
Is it in good condition?Go to Step 9.Repair or replace.
9Check engine coolant temp. sensor for performance
(See Section 6E1).
Is it in good condition?Go to Step 10.Replace engine
coolant temp.
sensor.
10Check parts or system which can cause engine rough
idle or poor performance.
–Engine compression (See Section 6A).
–Valve lash (See Section 6A).
–Valve timing (Timing belt installation. See Section 6A).
Are they in good condition?Check wire harness
and connection of
ECM (PCM) ground,
ignition system and
fuel injector for
intermittent open
and short.Repair or replace.
Fig. 1 for Step 3 Fig. 2 for Step 3 Fig. 3 for Step 4
Fig. 4 for Step 5 Fig. 5 for Step 7
Page 123 of 557
Oscilloscope Waveforms
Crankshaft
timing belt pulleyCKP
sensor
2V/Div.
5ms/Div.
Waveforms at specified idle speed
6-72 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0335 CRANKSHAFT POSITION (CKP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE
No CKP sensor signal during 1 revolution of
camshaft.CKP sensor circuit open or short.
Crankshaft timing belt pulley teeth damaged.
CKP sensor malfunction, foreign material being
attached or improper installation.
ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-3 (+) and C01-11 (–) of ECM (PCM) connector connected to ECM
(PCM) and check CKP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC, start engine and keep it at idle for 1 min.
2) Select “DTC” mode on scan tool and check DTC.
Page 175 of 557
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-19
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION
Engine oil ––––– level, leakage
Engine coolant ––––– level, leakage
Fuel ––––– level, leakage
A / T fluid ––––– level, leakage
Air cleaner element ––––– dirt, clogging
Battery ––––– fluid level, corrosion of terminal
Water pump belt ––––– tension, damage
Throttle cable ––––– play, installation
Vacuum hoses of air intake system ––––– disconnection,
looseness, deterioration, bend
Connectors of electric wire harness ––––– disconnection, friction
Fuses ––––– burning
Parts ––––– installation, bolt ––––– looseness
Parts ––––– deformation
Other parts that can be checked visually
Also check following items at engine start, if possible
Malfunction indicator lamp
Charge warning lamp
Engine oil pressure warning lamp
Engine coolant temp. meter
Fuel level meter
Tachometer, if equipped
Abnormal air being inhaled from air intake system
Exhaust system ––––– leakage of exhaust gas, noise
Other parts that can be checked visuallySection 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 6E2
Section 8
Section 6
Section 6H
Section 8 (Section 6 for pressure check)
Section 8
Section 8
Page 228 of 557
6-1-72 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Disconnect connectors when checking plugs
for spark1. Fuel delivery pipe
2. Fuel feed hose
3. FUel pressure
gauge & 3 way joint
STEPACTIONYESNO
6Check PCV valve for clogging (See Section 6E2).
Is it in good condition?Go to Step 7.Replace PCV valve.
7Check EVAP Canister Purge Valve for Closing.
1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose.
3) Check that vacuum is not felt there, when engine is
cool and running at idle. See Fig. 7.
Is vacuum felt?Check EVAP
control system
(See Section 6E2).Go to Step 8.
8Check intake manifold pressure sensor for performance
(See DTC P0105 Diag. Flow Table).
Is it in good condition?Go to Step 9.Repair or replace.
9Check engine coolant temp. sensor for performance
(See Section 6E2).
Is it in good condition?Go to Step 10.Replace engine
coolant temp.
sensor.
10Check parts or system which can cause engine rough
idle or poor performance.
–Engine compression (See Section 6A1).
–Valve lash (See Section 6A1).
–Valve timing (Timing belt installation. See Section 6A1).
Are they in good condition?Check wire harness
and connection of
ECM (PCM) ground,
ignition system and
fuel injector for
intermittent open
and short.Repair or replace.
Fig. 1 for Step 3 Fig. 2 for Step 3 Fig. 3 for Step 4
Fig. 4 for Step 5 Fig. 5 for Step 4 Fig. 6 for Step 5
Fig. 7 for Step 7
Page 229 of 557
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-73
Crankshaft
timing belt
pulleyCKP
sensor
Oscilloscope Waveforms
Waveforms at engine cranking (260 r/min) Waveforms at specified idle speed16 waives
for 10 signals13 waives for
10 signals
30 signal 30 signal 0.5 V / Div.
10 ms / Div.0.5 V / Div.
5 ms / Div.
DTC P0335 CRANKSHAFT POSITION (CKP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE
NO CKP sensor signal for 2 seconds at engine
cranking.CKP sensor circuit open or short.
Crankshaft timing belt pulley teeth damaged.
CKP sensor malfunction, foreign material being
attached or improper installation.
ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-23 (+) and C01-24 (–) of ECM (PCM) connector connected to ECM
(PCM) and check CKP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC and crank engine for 2 sec.
2) Select “DTC” mode on scan tool and check DTC.
Page 265 of 557
6A
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-1
SECTION 6A
ENGINE MECHANICAL
(G10, 1-CAM 6-VALVES ENGINE)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
For the descriptions (items) not found in this section, refer to the same section of Service Manual men-
tioned in FOREWORD of this manual.
CONTENTS
ON-VEHICLE SERVICE6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Vacuum Check6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Check6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head Cover6A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body and Intake Manifold 6A- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold6A- 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt and Belt Tensioner 6A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft and Hydraulic Valve Lash Adjuster 6A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Lash Adjuster Noise Diagnosis 6A-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valves and Cylinder Head6A-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pistons, Piston Rings, Connecting Rods and Cylinders 6A-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR OVERHAUL6A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Assembly6A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Bearings, Crankshaft and Cylinder Block 6A-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6A-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS6A-31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 274 of 557
1. Timing belt
2. Tensioner
3. Tensioner plate
4. Tensioner spring
5. Spring damper
6. Camshaft timing pulley
7. Pin
8. Pulley bolt
9. Seal
10. Inside cover seal
11. Inside cover
12. Outside cover seal
13. Outside cover
14. Tensioner stud
15. Tensioner bolt
16. Tensioner spring screw
: Tightening Torque
6A-10 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
TIMING BELT AND BELT TENSIONER
REMOVAL
1) Disconnect negative cable at battery.
2) Hoist vehicle.
3) Remove clip (2) after pushing center pin, and then remove fend-
er apron extension (1) on right side.
NOTE:
Do not push center pin (3) too far in, or it will fall off into
fender.
4) Remove air cleaner assembly as previously outlined.
5) Remove A / C compressor drive belt, if equipped.
6) Loosen water pump pulley bolts (1).
7) Loosen generator pivot bolts (3) and its adjusting bolt (2) and re-
move water pump belt (4) and its pulley (5).