2000 SUZUKI SWIFT Intake g13

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-31
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates current flow time rate within
a certain set cycle of IAC valve (valve opening rate)
which controls the amount of bypass air (idle speed).
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

6-1-34 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
CONNECTOR “C01”
TERMINAL
NO.CIRCUITNORMAL
VOLTAGECONDITION
1Ground——
2Ground——
3Ground——
4EVAP canister purge valve10 – 14 VIgnition switch ON
Indication
deflection
5Power steering switch
deflection
repeated
0 V and
Ignition switch ON
0 V and
10 – 14 V
6Idle air control valve0 – 13 VAt specified idle speed after engine warmed
up
7Heater of HO2S-110 – 14 VIgnition switch ON
8Fuel injector NO.410 – 14 VIgnition switch ON
9Fuel injector NO.110 – 14 VIgnition switch ON
10Sensor ground——
11Camshaft position sensor0 – 0.8 V
and 4 – 6 VIgnition switch ON
12Blank——
13Heater oxygen sensor-1Refer to DTC P0130 diag. flow table
14Engine coolant temp. sensor0.55 – 0.95 VIgnition switch ON
Engine coolant temp.: 80C (176F)
15Intake air temp. sensor2.0 – 2.7 VIgnition switch ON
Intake air temp.: 20C (68F)
16Blank——
17Electric load signal (+)
0 – 1 VIgnition switch ON
Small light and rear defogger OFF
17Electric load signal (+)
10 – 14 VIgnition switch ON
Small light and rear defogger ON
18Blank——
19Ignition coil #2——
20Ignition coil #1——
21Fuel injector NO.210 – 14 VIgnition switch ON
22Power source for sensor4.75 – 5.25 VIgnition switch ON
23Crankshaft position sensor (+)——
24Crankshaft position sensor (–)——
25Blank——
26Manifold absolute pressure
sensor3.3 – 4.0 VIgnition switch ON
Barometric pressure: 100 kPa (760 mmHg)
27Blank——
28Immobilizer indicator lamp0 – 2 VIgnition switch ON28Immobilizer indicator lamp10 – 14 VWhen engine running
29Blank——
30Blank——
31Fuel injector NO.310 – 14 VIgnition switch ON

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-45
Fig. 1 for Step 2 Fig. 2 for Step 3
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE”
performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check MAP Sensor and Its Circuit.
1) Connect scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON.
3) Check intake manifold pressure.
See Fig. 1.
Is it 114.7 kPa or more or 4.9 kPa or less?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to
“INTERMITTENT AND
POOR CONNECTION” in
Section 0A.
3Check Wire Harness.
1) Disconnect MAP sensor connector with
ignition switch OFF.
2) Check for proper connection of MAP
sensor at “Gr” and “G” wire terminals.
3) If OK, then with ignition switch ON, check
voltage at each of “P” and “Gr” wire
terminals. See Fig. 2.
Is voltage about 4 – 6 V at each terminal?Go to Step 4.“P” wire open or shorted to
ground circuit or shorted to
power circuit, “Gr” wire
open or shorted to ground,
poor C03-5 connection or
C01-22 connection.
If wire and connection are
OK, confirm that MAP
sensor is normal and then
substitute a known-good
ECM (PCM) and recheck.
NOTE: When battery
voltage is applied to
“P” wire, it is possible
that MAP sensor is also
faulty.
4Check MAP sensor according to “MAP
Sensor Individual Check” below.
Is it in good condition?“P” wire shorted to “Gr”
wire, “G” wire open,
poor C01-10 connection.
If wire and connection are
OK, substitute a known-
good ECM (PCM) and
recheck.Replace MAP sensor.

6-1-46 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
IAT sensor
To other sensors
DTC P0110 INTAKE AIR TEMP. (IAT) CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Low intake air temperature (High voltage-High resistance)

High intake air temperature (Low voltage-Low resistance)
“Gr / R” circuit open or shorted to power

“G” circuit open

IAT sensor malfunction

ECM (PCM) malfunction
NOTE:

When DTC P0115 and P0120 are indicated together, it is possible that “G” circuit is open.

Before inspecting, be sure to check that ambient temperature is higher than –40C (–40F).
DTC CONFIRMATION PROCEDURE
1) Clear DTC, start engine and keep it at idle for 1 min.
2) Select “DTC” mode no scan tool and check DTC.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-47
Fig. 1 for Step 2 Fig. 2 for Step 3 Fig. 3 for Step 4
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check IAT Sensor and Its Circuit.
1) Connect scan tool to DLC with ignition switch
OFF.
2) Turn ignition switch ON.
3) Check intake air temp. displayed on scan tool.
See Fig. 1.
Is –40C (–40F) or 119C (246F) indicated?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection”
in Section 0A.
3Check Wire Harness.
1) Disconnect IAT sensor connector with ignition
switch OFF.
2) Check for proper connection to IAT sensor at
“Gr / R” and “G” wire terminals.
3) If OK, then with ignition switch ON, is voltage
applied to “Gr / R” wire terminal about 4 – 6 V?
See Fig. 2.Go to Step 5.“Gr / R” wire open or
shorted to power, or
poor C01-15
connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.
4Does scan tool indicate –40C (–40F) at Step 2.Go to Step 6.Go to Step 5.
5Check Wire Harness
1) Check intake air temp. displayed on scan tool
with ignition switch ON.
Is –40C (–40F) indicated?Replace IAT sensor.“Gr / R” wire shorted to
ground.
If wire is OK, substitute
a known-good ECM
(PCM) and recheck.
6Check Wire Harness.
1) Using service wire, connect IAT sensor
connector terminals.
2) Check intake air temp. displayed on scan tool
with ignition switch ON. See Fig. 3.
Is 119C (246F) indicated?Replace IAT sensor.“Gr / R” wire open or
poor C01-10
connection.
If wire and connection
are OK, substitute a
known-good ECM
(PCM) and recheck.

6-1-52 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Throttle
position
sensorTo other sensors
To other sensors
DTC P0121 THROTTLE POSITION CIRCUIT RANGE / PERFORMANCE
PROBLEM
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

After engine warmed up.

While vehicle running at specified engine speed.

No change in intake manifold pressure (constant throttle opening)

Difference between actual throttle opening (detected from TP sensor)
and opening calculated by ECM (PCM) (Obtained on the basis of
engine speed and intake manifold pressure) in larger than specified
value.
2 driving cycle detection logic, continuous monitoring
TP sensor malfunction

High resistance in the circuit

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF. Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Indication of fuel level meter in combination meter: 1 / 4 or more
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: between –10C and 80C (14F and 176F)
–Engine coolant temp.: 70C, 158F or higher
2) Warm up engine to normal operating temperature.
3) Increase vehicle speed to 30 – 40 mph, 50 – 60 km / h in 3rd gear or “D” range and hold throttle valve at that
opening position for 1 min.
4) Stop vehicle.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.

6-1-54 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Ignition
switch
Main
fuse
To HO2S-2 heaterTo other sensor
Heater Fuse box
DTC P0130 HEATED OXYGEN SENSOR (HO2S) CIRCUIT MALFUNCTION
(SENSOR-1)
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

When running at idle speed after engine warmed up
and running at specified vehicle speed, HO2S-1
output voltage does not go 0.3 V below or over
0.6 V.
2 driving cycle detection logic, Monitoring once / 1
driving.
Heated oxygen sensor-1 malfunction

“G” or “R” circuit open (poor connection) or short
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF. Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: between –10C and 80C (14F and 176F)
2) Warm up engine to normal operating temperature.
3) Drive vehicle at 38 – 50 mph, 60 – 80 km / h for 2 min.
4) Stop vehicle and run engine at idle for 2 min.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-61
Usual driving: Driving at 30 – 40 mph, 50 – 60 km/h including short stop according to traffic signal. (under driving condition other than high-load,
high-engine speed, rapid accelerating and decelerating)1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11)and 50 mph
(80 km / h)
Above 20 mph
(32 km / h) Usual driving
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF.
Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: –10C, 14F or higher
–No exhaust gas leakage and loose connection
2) Warm up engine to normal operating temperature.
3) Drive vehicle under usual driving condition for 5 min. and check HO2S-2 output voltage and “short term fuel
trim” with “Data List” mode on scan tool, and write it down.
4) Stop vehicle (don’t turn ignition switch OFF).
5) Increase vehicle speed to higher than 20 mph, 32 km / h and then stop vehicle.
6) Repeat above steps 5) 4 times.
7) Increase vehicle speed to about 50 mph (80 km / h) in 3rd gear or 2 range.
8) Release accelerator pedal and with engine brake applied, keep vehicle coasting (fuel cut condition) for 10sec.
or more.
9) Stop vehicle (don’t turn ignition switch OFF) and run engine at idle for 2 min.
After this step 9), if “Oxygen Sensor Monitoring TEST COMPLETED” is displayed in “READINESS TESTS”
mode and DTC is not displayed in “DTC” mode, confirmation test is completed.
If “TEST NOT COMPLTD” is still being displayed, proceed to next step 10).
10) Drive vehicle under usual driving condition for 10 min. (or vehicle is at a stop and run engine at idle for 10 min.
or longer)
11) Stop vehicle (don’t turn ignition switch OFF). Confirm test results according to “Test Result Confirmation Flow
Table” in “DTC CONFIRMATION PROCEDURE” of DTC P0420.