2000 SUZUKI SWIFT throttle

21
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-17
2) Connect engine coolant hoses (1).
3) Install throttle body (4) to intake manifold.
4) Connect coupler to TP sensor (2) and IAC valve (3) securely.
5) Install air cleaner outlet hose (1) and pipe.
6) Connect accelerator cable and adjust cable play to specifica-
tion.
7) Refill cooling system.
8) Connect negative cable at battery.
IDLE AIR CONTROL VALVE (IAC VALVE)
Removal
1) Remove throttle body from intake manifold referring to “Throttle
Body Removal” section.
2) Remove IAC valve from throttle body.
Inspection
1) Connect each connector to IAC valve (1), TP sensor and IAT
sensor.
2) Check that rotary valve (2) of lAC valve opens and closes once
and then stops in about 60 ms as soon as ignition switch is
turned ON.
NOTE:

This check should be performed by two people, one per-
son turns on ignition switch while the other checks valve
operation.

As valve operation is momentary, it may be overlooked.
To prevent this, perform this operation check 3 times or
more continuously.
If rotary valve of lAC valve does not operate at all, check
wire harness for open and short. If wire harness is in good
condition, replace lAC valve and recheck.

3. Fuel return pipe
6E2-18 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
Installation
1) Install new O-ring (2) to IAC valve (1).
2) Install IAC valve (1) to throttle body (3).
Tighten IAC valve screws to specified torque.
Tightening Torque
(a): 3.3 N
.m (0.33 kg-m, 2.5 lb-ft)
3) Install throttle body to intake manifold referring to “Throttle Body
Installation” section.
FUEL DELIVERY SYSTEM
FUEL PRESSURE INSPECTION
WARNING:
Be sure to perform work in a well-ventilated area and away
from any open flames, or there is a risk of a fire breaking out.
1) Relieve fuel pressure in fuel feed line referring to “Fuel Pressure
Relief Procedure” in Section 6.
2) Disconnect fuel feed hose from fuel delivery pipe.
CAUTION:
A small amount of fuel may be released when fuel hose
is disconnected. Place container under the joint with a
shop cloth so that released fuel is caught in container or
absorbed in cloth. Place that cloth in an approved con-
tainer.
3) Connect special tools and hose between fuel delivery pipe (1)
and fuel feed hose (2) as shown in figure, and clamp hoses se-
curely to ensure no leaks occur during checking.
Special Tool
(A): 09912-58441
(B): 09912-58431
(C): 09912-58490
4) Check that battery voltage is above 11 V.

1
2
3
1. Ground terminal
2. Reference voltage terminal
3. Output voltage terminal
(a)
1
23
4
6E2-28 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
THROTTLE POSITION SENSOR (TP SENSOR)
Inspection
1) Disconnect negative cable at battery and coupler from TP sen-
sor.
2) Using ohmmeter, check resistance between terminals under
each condition given in table below.
TERMINALS
RESISTANCE
Between 1 and
2 terminals2.5 – 6.0 kΩ
Between 1 and
Throttle valve is
at idle position0.17 – 11.4 kΩ
3 terminalsThrottle valve is
fully opened1.72 – 15.50 kΩ
NOTE:
There should be more than 1.5 kΩ resistance difference
between when throttle valve is at idle position and when
it is fully open.
If check result is not satisfactory, replace TP sensor.
3) Connect TP sensor coupler securely.
4) Connect negative cable to battery.
Removal
1) Disconnect battery negative cable at battery.
2) Disconnect coupler from TP sensor.
3) Remove TP sensor from throttle body.
Installation
1) Install TP sensor (1) to throttle body.
Fit TP sensor to throttle body in such way that its holes (3) are
a little away from TP sensor screw holes (2) as shown in left fig-
ure and turn TP sensor clockwise so that those holes align (4).
Tightening Torque
(a): 2.0 N
.m (0.20 kg-m, 1.5 lb-ft)
2) Connect coupler to TP sensor securely.
3) Connect battery negative cable to battery.

6E2-34 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
FUEL CUT OPERATION
Inspection
NOTE:
Before inspection, check to make sure that gear shift lever is
in neutral position (with A / T model, selector lever in “P”
range), A / C is OFF and that parking brake lever is pulled all the
way up.
1) Warm up engine to normal operating temperature.
2) While listening to sound of injector (1) by using sound scope (2)
or such, increase engine speed to higher than 3,000 r / min.
3) Check to make sure that sound to indicate operation of injector
stops when throttle valve is closed instantly and it is heard again
when engine speed is reduced to less than about 2,000 r / min.
RADIATOR FAN CONTROL SYSTEM
System Inspection
WARNING:
Keep hands, tools, and clothing away from engine cooling
fan to help prevent personal injury. This fan is electric and
can come on whether or not the engine is running. The fan
can start automatically in response to the ECT sensor with
the ignition switch in the ON position.
Check system for operation referring to Flow Table B-8 in Section
6.
If radiator fan fails to operate properly, check relay, radiator fan and
electrical circuit.
Radiator Fan
Inspection
1) Check continuity between each two terminals.
If there is no continuity, replace radiator fan motor.

1. Injector coupler
2. Throttle body
3. Air cleaner case
4. Cylinder head cover
1. High-tension code 2. Cap
1. High-tension
cord
2. Ohmmeter
IGNITION SYSTEM 6F-5
ON-VEHICLE SERVICE
IGNITION SPARK TEST
1) Disconnect injector coupler at throttle body side.
WARNING:
Without disconnection of injector coupler, combustible gas
may come out from spark plug holes during this test and
may get ignited in engine room.
2) Remove spark plugs and connect them to high-tension cords,
and then ground spark plugs.
3) Crank engine and check if each spark plug sparks.
4) If no spark is emitted, inspect high-tension cords, spark plugs,
ignition coil, distributor, etc.
HIGH-TENSION CORDS
1) Remove high-tension cord at ignition coil while gripping its cap.
2) Remove distributor cap installed with high-tension cords.
3) Remove high-tension cord clamp from cylinder head cover.
4) Pull out high-tension cords from spark plugs while gripping each
cap.
CAUTION:

Removal of high-tension cords together with clamps
will be recommended so as not to damage their inside
wire (resistive conductor).

For the same reason, pull out each connection by grip-
ping cap portion.
5) Measure resistance of high-tension cord by using ohmmeter.
High-tension cord resistance: 10 – 22 kΩ/ m (3.0 – 6.7 kΩ/ft)

6F1-8 IGNITION SYSTEM (SFI FOR G13)
5) Fix ignition timing to initial one as follow.
Select “MISC” mode on SUZUKI scan tool and fix ignition tim-
ing to initial one.
6) Detach air cleaner case and shift air cleaner case and hose
position to observe ignition timing.
7) Using timing light (1), check that ignition timing is within specifi-
cation.
Initial ignition timing (fixed with
SUZUKI scan tool) : 5
3 BTDC at idle speed
Ignition order : 1-3-4-2
8) If ignition timing is out of specification, check the followings:

CKP sensor

Crankshaft timing belt pulley (signal rotor)

TP sensor

VSS

Timing belt cover installation
9) After checking Initial Ignition Timing, release ignition timing
fixation by using SUZUKI scan tool.
10) With engine idling (throttle opening at closed position and ve-
hicle stopped), check that ignition timing is about 9–15
BTDC. (Constant variation within a few degrees from 9–15
indicates no abnormality but proves operation of electronic tim-
ing control system.) Also, check that increasing engine speed
advances ignition timing.
If above check results are not satisfactory, check CKP sensor
and ECM (PCM).
11) Install air cleaner case.

7B-2 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
Table B-1 Gear Shift Failure in “D” or
“2” Range 7B-38. . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 Gear is Shifted to 2nd Gear in
“L” Range Vehicle Does Not Move
Backward in “R” Range 7B-38. . . . . . . . . . . . . .
Transmission range sensor check 7B-39. . . . Output shaft speed sensor check 7B-39. . . . .
Shift solenoid valve circuit check 7B-40. . . . . .
Throttle position sensor check 7B-41. . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7B-42 . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS7B-42 . . . . . . . . . . . . . . . . . . . . . .

[G10 Engine Model]
1. PCM
2. Camshaft position (CMP) sensor
3. Throttle position (TP) sensor
4. Engine coolant temperature (ECT) sensor
5. Transmission range sensor (shift switch)
6. Output shaft speed sensor (A / T VSS)7. Malfunction indicator lamp (MIL)
8. Data link connector (DLC)
9. Shift solenoid-A
(No.1, Direct clutch solenoid valve)
10. Shift solenoid-B
(No.2, 2nd brake solenoid valve)11. Ignition switch
12. Main relay
13. Inhibitor switch
14. To starter
15. Terminal arrangement of PCM coupler
(Viewed from harness side)
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-5
ELECTRONIC SHIFT CONTROL SYSTEM