Page 125 of 801
YH4
GRAND
VITARA
1B-54 AIR CONDITIONING (OPTIONAL)
2
4) Remove shims from shaft.
5) Using special tool (C), remove circlip.
Special Tool
(C): 09900-06107
6) Remove clutch coil lead wire clamp screw, and remove clutch
coil read wire ground terminal.
7) Remove clutch pulley with puller (1) from compressor (2).
NOTE:
Be careful not to damage pulley when tapping magnet
clutch assembly.
8) Remove clutch coil.
Special tool
(C): 09900-06107
INSTALLATION
1) Install clutch coil (2).
Protrusion on under side of coil ring must match hole in com-
pressor (3) to prevent movement ant correctly locate lead wire.
2) Using special tool (C), install snap ring (1) as shown.
Special Tool
(C): 09990-06107
3) Install clamp portion and ground terminal of lead wire.
Page 127 of 801

YH4
GRAND
VITARA
1B-56 AIR CONDITIONING (OPTIONAL)
1. Clutch plate bolt
2. Clutch plate
3. Circlip
4. Clutch pulley
5. Washer
6. Shim
7. Oil felt ring
8. Clutch coil
9. Lip type seal
10. Compressor front head
11. Compressor body component
12. O-ring
13. Compressor thermal switch
3. Washer
(if equipped)1. Thermal switch
2. Ohmmeter
MAGNET CLUTCH ASSEMBLY (FOR SEIKO SEIKI)
INSPECTION
MAGNET CLUTCH
Inspect clutch plate and clutch pulley for signs of oil.
Check clutch pulley bearings for noise and grease leakage.
Using and ohmmeter, measure resistance of clutch coil between
clutch coil lead wire (1) and compressor body.
If measured resistance is not within tolerance, replace coil.
Standard resistance: 2.5 ± 4.5 at 20C, 68F
COMPRESSOR THERMAL SWITCH
Use an ohmmeter to check thermal switch for continuity. If there is
no continuity, replace it.
REMOVAL
1) Remove compressor assembly from vehicle. Refer to COM-
PRESSOR ASSEMBLY in this section.
2) Fix clutch plate (1) with special tool (A) and remove clutch plate
bolt (2).
Special Tool
(A): 09991-06020
NOTE:
Do not reuse armature plate nut.
Page 128 of 801
YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-57
3) Using special tool (B), remove clutch plate (1).
Special Tool
(B): 09991-06030
4) Disconnect clutch coil lead wire from compressor thermal switch
led wire.
5) Remove felt ring (if equipped) and shims from shaft.
6) Using special tool (C), remove circlip.
Special Tool
(C): 09900-06107
7) Remove clutch coil lead wire clamp screw.
8) Remove clutch pulley with puller (1) from compressor (2).
NOTE:
Be careful not to damage pulley when tapping magnet
clutch.
9) Remove clutch coil.
INSTALLATION
1) Install clutch coil (2).
Protrusion on under side of clutch coil must match hole in com-
pressor (3) to prevent movement ant correctly locate lead wire.
2) Using special tool (C), install snap ring (1) as shown.
Special Tool
(C): 09990-06107
3) Clamp covering portion of lead wire.
Page 130 of 801
YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-59
PUSH
3. Cylinder
4. Case
5. O-ring
2. Bearing puller
LIP TYPE SEAL (FOR SEIKO SEIKI)
REMOVAL
1) Remove magnet clutch assembly, referring to ªMAGNET
CLUTCH ASSEMBLYº in this section.
2) Remove compressor front head (1) mounting bolt (10 pcs.).
3) Remove compressor front head (1) by pushing cylinder shaft
(2).
NOTE:
Be careful not to remove cylinder from case.
4) Remove O-ring.
5) Remove lip seal from compressor front head (1).
INSTALLATION
1) Press-fit lip seal (1) into compressor front head (2) using special
tool (E).
Special Tool
(E): 09991-06050
CAUTION:
Do not reuse mechanical seal once removed from com-
pressor.
Page 132 of 801
YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-61
09900-06107
Snap ring pliers
(Opening type)09991-06010
Magnet clutch pulley installer09991-06020
Armature plate spanner09991-06030
Armature plate remover
09991-06040
Lip type seal protector09991-06050
Lip type seal installer
REQUIRED SERVICE MATERIAL
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Compressor oil for DENSO
compressor (Refrigerant oil)COMPRESSOR OIL (ND-OIL 8, 250 cc)
99000-27080O-ring
Each component
Compressor oil for
SEIKO SEIKI compressor
(Refrigerant oil)COMPRESSOR OIL RS20 (150 cc)
99000-99088-00DO-ring
Each component
RefrigerantREFRIGERANT DRUM (200 g)
95794-50G00Refrigerant charge
SPECIAL TOOLS
Page 133 of 801

YH4
GRAND
VITARA
3
STEERING, SUSPENSION, WHEELS AND TIRES 3-1
GENERAL DIAGNOSIS3-1 . . . . . . . . . . . . . . . . .
Diagnosis Table 3-1. . . . . . . . . . . . . . . . . . . . . .
TIRE DIAGNOSIS3-6 . . . . . . . . . . . . . . . . . . . . . .
Irregular and / or Premature Wear 3-6. . . . . . .
Wear Indicator 3-6. . . . . . . . . . . . . . . . . . . . . . . Radial Tire Waddle 3-6. . . . . . . . . . . . . . . . . . .
Radial Tire Lead 3-8. . . . . . . . . . . . . . . . . . . . . .
VIBRATION DIAGNOSIS3-8 . . . . . . . . . . . . . . .
SECTION 3
STEERING, SUSPENSION, WHEELS AND TIRES
DIAGNOSIS3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT END ALIGNMENT3A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER STEERING SYSTEM3B1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR BAG STEERING WHEEL AND COLUMN3C1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT SUSPENSION3D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR SUSPENSION3E-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHEELS AND TIRES3F-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DIAGNOSIS
Since the problems in steering, suspension, wheels and tires involve several systems, they must all be considered
when diagnosing a complaint. To avoid using the wrong symptom, always road test the vehicle first.
Proceed with the following preliminary inspections and correct any defects which are found.
1) Inspect tires for proper pressure and uneven wear.
2) Raise vehicle on a hoist and inspect front and rear suspension and steering system for loose or damaged parts.
3) Spin front wheel. Inspect for out-of-round tires, out-of-balance tires, bent rims, loose and / or rough wheel bear-
ings.
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Vehicle Pulls (Leads)Mismatched or uneven tires.
Tires not adequately inflated.
Broken or sagging springs.
Radial tire lateral force.
Disturbed front end alignment.
Disturbed rear axle alignment.
Brake dragging in one road wheel.
Loose, bent or broken front or rear
suspension parts.Replace tire.
Adjust tire pressure.
Replace spring.
Replace tire.
Check front end alignment.
Check rear axle alignment.
Repair front brake.
Tighten or replace suspension part.
Page 134 of 801

YH4
GRAND
VITARA
3-2 STEERING, SUSPENSION, WHEELS AND TIRES
ConditionPossible CauseCorrection
Abnormal or
Excessive Tire WearSagging or broken springs.
Tire out of balance.
Disturbed front end alignment.
Faulty shock absorber.
Hard driving.
Overloaded vehicle.
Tires not rotating.
Worn or loose road wheel bearings.
Wobbly wheel or tires.
Tires not adequately inflated.Replace spring.
Adjust balance or replace tire.
Check front end alignment.
Replace shock absorber.
Replace tire.
Replace tire.
Replace or rotate tire.
Replace wheel bearing.
Replace wheel or tire.
Adjust the pressure.
Wheel TrampBlister or bump on tire.
Improper shock absorber action.Replace tire.
Replace shock absorber.
Shimmy, Shake or
VibrationTire or wheel out of balance.
Loose wheel bearings.
Worn tie rod ends.
Worn lower ball joints.
Excessive wheel runout.
Blister or bump on tire.
Excessively loaded radial runout of
tire / wheel assembly.
Disturbed front end alignment.
Loose or worn tie-rod end.
Loose steering gear case bolts.Balance wheels or replace tire and /
or wheel.
Replace wheel bearing.
Replace tie rod end.
Replace front suspension control
arm.
Repair or replace wheel and / or tire.
Replace tire.
Replace tire or wheel.
Check front end alignment.
Tighten or replace tie-rod end.
Tighten case bolts.
Hard SteeringBind in tie rod end ball studs or
lower ball joints.
Disturbed front end alignment.
Rack and pinion not properly adjusted.
(if equipped with manual steering gear
case)
Tire not adequately inflated.
Bind in steering column.
Low fluid level, loose drive belt or
malfunction of power steering system.
(if equipped with P / S)Replace tie rod end or front
suspension control arm.
Check front end alignment.
Check and adjust steering gear box.
Inflate tires to proper pressure.
Repair or replace.
Check and correct.
Page 135 of 801

YH4
GRAND
VITARA
STEERING, SUSPENSION, WHEELS AND TIRES 3-3
ConditionPossible CauseCorrection
Too Much Play in
SteeringWheel bearings worn.
Loose steering gear case bolts.
Rack and pinion not properly adjusted.
(if equipped with manual steering gear
case)
Worn steering shaft joints.
Worn tie rod ends or tie rod
inside ball joints.
Worn lower ball joints.Replace wheel bearing.
Tighten.
Check and adjust rack and pinion
torque.
Replace joint.
Replace tie rod end or steering
gear case.
Replace front suspension control
arm.
Poor ReturnabilityBind in tie rod end ball studs.
Bind in ball joints.
Bind in steering column.
Poorly lubricated rack and pinion.
(if equipped with manual steering gear
case)
Disturbed front end alignment.
Rack and pinion not properly adjusted.
(if equipped with manual steering gear
case)
Tires not adequately inflated.Replace tie rod end.
Replace ball joint.
Repair or replace.
Check, repair or lubricate rack and
pinion.
Check and adjust front end
alignment.
Check and adjust rack and pinion
torque.
Adjust pressure.
Steering Noise
(Rattle or Chuckle)Loose bolts and nuts.
Broken or otherwise damaged wheel
bearings.
Worn or sticky tie rod ends.
Rack and pinion not properly adjusted.
(if equipped with manual steering gear
case)Retighten.
Replace.
Replace.
Check and adjust rack and pinion
torque.
Abnormal Noise,
Front EndWorn, sticky or loose tie rod
ends, lower ball joints, tie rod
inside ball joints or drive shaft
joints.
Damaged shock absorbers, struts
or mountings.
Worn control arm bushings.
Loose stabilizer bar.
Loose wheel nuts.
Loose suspension bolts or nuts.
Broken or otherwise damaged
wheel bearings.
Broken suspension springs.
Poorly lubricated or worn strut
bearings.Replace tie rod end, control arm,
steering gear case or drive shaft
joint.
Replace or repair.
Replace.
Tighten bolts or replace bushes.
Tighten wheel nuts.
Tighten suspension bolts or nuts.
Replace wheel bearing.
Replace spring.
Lubricate or replace strut bearing.