SWS -Troubleshooting54B-47
Inspection Procedure P-10
Driver’s door switch signal is not sent to the ETACS-ECU.Probable cause
Door switches signal is not sent to the ETACS-ECU.
The driver’s door switch is used to operate the following functions. If the signal
fails, these devices will not work normally.
DLight reminder warning buzzer function
DForgotten key prevention function
DPower window timer function
DIgnition key hole illumination lamp
DHeadlamp automatic shutdown function
The door switches is used to operate the following devices. If the signal fails,
these devices will not work normally.
DKeyless entry system
DRoom lamp dimming functionDMalfunction of driver’s, front passenger’s, rear or
back door switch
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
NG
Repair
OK
NG
Repair
OK
Replace the ETACS-
ECU.
NG
Repair
NG
Check the harness wire between door switch and ETACS-ECU.
OKCheck trouble symptoms.
Check the following connectors :
Front L.H. door: F-20, D-26, D-218, D-224
Front R.H. door: F-03, D-124, D-209, D-224
Rear L.H. door: F-14, D-26, D-218, D-224
Rear R.H. door: F-10, D-124, D-209, D-224
Back door: G-03, D-26, D-218, D-224
Check the following connectors :
Front L.H. door: F-20, D-26, D-209, D-224
Front R.H. door: F-03, D-219, D-224
Rear L.H. door: F-14, D-26, D-209, D-224
Rear R.H. door: F-10, D-219, D-224
Back door: G-03, D-26, D-209, D-224
Check the installation of the door switch to the vehicle body.
Check the door switch. (Refer to GROUP 42 – Door or GROUP
42 - Back Door.)NG
Replace
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
SWS -Troubleshooting54B-51
Inspection Procedure P-16
Power window main switch: Any switch signal is not sent
to the ETACS-ECU.Probable cause
If there is a problem with communication between the power windowmainswitch
and the ETACS-ECU, the input signal check for the power windowmainswitch
can no longer be carried out. In addition, the power window timer function will
also stop working.DMalfunction of power windowmainswitch
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
Ye s
NG
Repair
NG
No
(1) NG
NG
Repair
NG
Check the harness wire between power windowmainswitch and
power window relay.
OK
Replace the power windowmainswitch.
NG
Repair
NG
Check the harness wire between power windowmainswitch and
body earth.
NG
Repair
Check trouble symptoms.NGReplace the ETACS-
ECU.
OK
Check trouble symptoms.
(2) NG
Check the following connectors:
H-05, D-25
OK
Check trouble symptoms.
Check the following connectors:
H-05, H-25, D-208, D-221Measure at power windowmainswitch connector H-05.
DDisconnect connector and measure at harness side.
DTurn the ignition switch to ON position.
(1) Voltage between terminal 1 or
5 and body earth.
OK:System voltage
(2) Continuity between terminal 5
or 3 and body earth.
OK:Continuity
OK
Replace the power win-
dow mainswitch
Check the harness wire between power windowmainswitch and
ETACS-ECU.
OK
Check trouble symptoms.
Check the following connectors:
H-05, D-25, D-31, D-226Can the driver’s side power window be operated by the power
window mainswitch?
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
