MAINTENANCE
9–3
Petrol-powered vehicles (1600, 1800 models)
M03A027a
This check must be carried out with the ve-
hicle on a flat level surface with the engine at
normal operating temperature, but NOT run-
ning. If the engine has been running, wait for
a few minutes to allow the engine oil to return
to the oil pan to ensure an accurate
measurement.
Remove the dipstick and wipe it with a clean
cloth, re - insert the dipstick as far as it will go.
Remove the dipstick and check the oil level.
This should always be within the range as
indicated.
If the oil level is below the specified limit, re-
move the filler cap and add oil. Then recheck
the level. When satisfied that the level is cor-
rect, refit the oil filler cap making sure that it
is securely fitted.
Diesel-powered vehicle
M03A090a
Use only the recommended oils with an API
or ACEA classification as specified in this
manual.
NOTE
(1)Engine oil consumption is greatly in-
fluenced by payload, engine speed,
etc. It may reach 1.0 lit./1,000 km de-
pending on style of driving.
(2) The engine oil will deteriorate rapidly if
the vehicle is subjected to severe condi-
tions (for example, repeated operation
on rough roads, in mountainous re-
gions, on roads with many uphill and
downhill gradients, or over short dis-
tances). Consequently, the oil will re-
quire earlier replacement.
(3) For handling of used engine oils, refer to
page
1–11.
Petrol-powered vehicles
M03B037a
Selection of engine oil
(petrol-powered vehicle)
EM03B-Of
(1) Select engine oil of the proper SAE vis-
cosity number according to the atmos-
pheric temperature.
For 0W-30, 5W-30, 0W-40 and 5W-40
viscosity grade, use only ACEA A3
classification.
(2) Use engine oil conforming to the follow-
ing classification:
ACEA classification:
“For service A1, A2 or A3”
API classification:
“FOR SERVICE SG” or higher
NOTE
Use of additives is not recommended since
they may reduce the effectiveness of addi-
tives already included in the engine oil. It
may result in failure of the mechanical as-
sembly.
MAINTENANCE
9–4
Type 1
M03B029a
Selection of engine oil
(diesel-powered vehicles)
EM03BAKe
(1) Select engine oil of the proper SAE vis-
cosity number according to the atmos-
pheric temperature.
(2) Use engine oil conforming to the follow-
ing classification:
Ty p e 1 :ACEA classification:
“For service B2-96 or B3-96”
Ty p e 2 :API classification:
“For service CF”
NOTE
Use of additives is not recommended
since they may reduce the effectiveness of
additives already included in the engine
oil. It may result in failure of the mechani-
cally assembly.
Type 2
M03B030aM05A069a
Automatic transmission fluid*EM05AAH
The proper amount of automatic trans-
mission fluid is essential to the life and oper-
ation of the automatic transmission. Either in-
sufficient fluid or excessive fluid could cause
transmission trouble. The transmission fluid
filler port cap is equipped with a dipstick. Use
the following procedure to check the fluid
level.
1. Check the fluid level after the vehicle
has been driven enough to warm up
the transmission fluid.
2. Park the vehicle on a flat, level surface
and apply the parking brake.
SPECIFICATIONS
10–16
CapacitiesEQ02AMFj
No.ItemQuantityRecommended lubricants
1Power steering fluidAs requiredATF DEXRON II
1300Oil pan3.0 litres
Petrol-powered
1300Oil filter0.3 litre
2Engine oil
powered
vehicles1600,Oil pan3.5 litresRefer to page 9 22Engine oil1800Oil filter0.3 litreRefer to page 9–2
Diesel-poweredOil pan4.9 litrespowered
vehiclesOil filter0.16 litre
3Brake fluidAs requiredBrake fluid DOT 3 or DOT 4
4Clutch fluidAs requiredBrake fluid DOT 3 or DOT 4
5Washer fluid4.8 litres–
6Engine coolant6.3 litresHigh-quality ethylene glycol includes coolant (including 0.65 litre in the reserve tank)
7Automatic transmission fluid7.7 litresDIA QUEEN ATF SP III
–ManualPetrol-powered1300, 16003.4 litresELF TPM 4447 75W-80WManual
transmission
oil
powered
vehicle1800 (GDI)2.2 litresGear oil API classification GL-4 SAE 75W-85W or 75W-90oilDiesel-powered vehicle2.1 litresVolvo oil 97308
–Refrigerant (air conditioning)680-720 gHFC–134a
NOTE
Points requiring routine inspection or replenishment such as the engine oil, coolant, automatic transmission fluid, brake fluid are marked white for easy identification.
