2000 LEXUS GS400 key battery

AT061±01
D01925
ACC
EP1KLS+
SLS+
Z16909
4 (+)
3 (±)
Z16910
4 (+)
3 (±)
AT±12
± AUTOMATIC TRANSMISSIONSHIFT LOCK SYSTEM
1960 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL ECU
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the ECU connector.
TerminalMeasuring ConditionSpecified Condition
(1) IG SW ACC and shift lever P position0 V
1 ± 10 (KLS ± E)(2) IG SW ACC and shift lever except P position7.5 ± 11V (about I second)
after 6 ± 9 V
4 10 (ACC E)(1) IG SW ON10 ± 14 V4 ± 10 (ACC ± E)(2) IG SW ACC10 ± 14 V
7 10 (P1 E)(1) Shift lever P position0 V7 ± 10 (P1 ± E)(2) Shift lever except P position10 ± 14 V
(1) IG SW ON and shift lever P position0 V
8 10 (SLSE)(2) IG SW ON and depress brake pedal or shift lever N position3 ± 6 V8 ± 10 (SLS ± E)(3) IG SW ON and release brake pedal or shift lever except P position0 V
(4) IG SW ACC and shift lever except P position3 ± 6 V
10 ± Ground (E ± Ground)ConstantContinuity
2. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals 3 and 4.
Standard resistance: 12 ± 17 W
If the resistance value is not as specified, replace the solenoid.
(c) Touch the solenoid with your finger and check that the so-
lenoid operation can be felt when battery voltage is ap-
plied intermittently to terminals 3 and 4.
If the operation is not as specified, replace the solenoid.

DI3CO±10
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±141
2442 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
PRE±CHECK
1. THEFT DETERRENT SYSTEM
When the system is set to the theft deterrent mode and any of
the following conditions are met, the system sounds the horns
and flashes the headlights and the taillights for approx. 1 min-
ute.
At the same time the system locks all doors (If all door are not
locked at once, the system repeats door locking operation ev-
ery 0.55 seconds during the one minute alarm time).
There are 2 modes in this system, which are active mode and
passive mode.
All initial setting are performed in active mode. It can be
switched to passive mode by specified operation. (See step 4.
CHANGING METHOD OF PASSIVE MODE)
Condition:
Any of the doors (Including the engine hood and luggage
compartment door) is unlocked or opened without the
key. *1
The battery terminal is disconnected and reconnected.
The system receives panic signal from remote keyless
entry. *2
*1: Only active arming mode.
*2: When the ignition key is not inserted in the key cylin-
der.
There are 4 conditions in this system which are disarming
condition, disarming preparation condition, arming condition
and alarming condition.
(a) Disarming condition:
(1) When a user is near the vehicle.
(2) When the alarming function does not operate.
(3) When theft deterrent function is not performed.
(b) Disarming preparation condition:
(1) Time from a user locks a door to be leaves the ve-
hicle.
(2) Time until transferring to disarming condition.
(3) Theft deterrent function is not performed.
(c) Arming condition:
(1) When a user leaves the vehicle completely.
(2) When theft deterrent function is possible.

Disarming condition
Any of the following conditions is met

When all doors and engine hood are closed, lock all the doors using a key.

When all doors and engine hood are closed, lock all the doors using wireless remote function.

When all doors and engine hood are closed, open and close either of doors and engine hood
then close and lock all doors and engine hood.
Disarming preparation condition
Any of the following conditions is met

30 seconds elapse when the engine hood
is closed and all doors are locked.
Any of the following conditions is met

Close and open either of all doors and
engine hood.

Lock and unlock either of doors.

Insert a key into the ignition key cylinder.

Reconnect the battery.
Arming condition
Any of the following conditions is met

Unlock the locked doors using the wireless
remote function.

Unlock the locked doors using the key.

Insert the key into the ignition key cylinder
and turn the ignition key ON.
Any of the following conditions is met

Either of closed doors opens.

Either of locked doors is unlocked by any
operation other than key or wireless remote
function.

The closed engine hood is opened.

The battery is reconnected.
Alarming condition
Any of the following conditions is met

Unlock the locked doors using the wireless
remote function.

Unlock the locked doors using the key.

Insert the key into the ignition key cylinder
and turn the ignition key ON.
In this mode, once theft is detected, it is
informed using light and sound to people
around the vehicle.
The alarming time described above passes.
(Key not inserted in ignition cylinder.)
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±143
2444 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
2. ACTIVE ARMING MODE

Disarming condition (A)
Disarming preparation condition
Any of the following
conditions is met

With all doors and
engine hood closed
30 seconds elapse.
Arming condition
Any of the following conditions is met
(Refer to HINT * on the next page)

Press unlock switch of the wireless.

Insert the key into the driver and passenger
doors key cylinders, turn the key to unlock.

Insert the key into the ignition key cylinder
and turn the key to ON.
Any of the following conditions is met

Either of closed door is opened and entry
delay time elapses. (Refer to HINT on the
next page)

Engine hood is closed and opened.

Battery is reconnected.
Alarming condition
In this mode, once theft is detected, it is
informed using light and sound to people
around the vehicle.
The alarming time described above passes.
Any of the following conditions is met

Pull the key out of the ignition key cylinder which the key was inserted in.
Disarming condition (B)
Any of the following conditions is met

Press the unlock button of wireless.

Insert the key into the key cylinder of driver
or passenger seat and turn the key to unlock.

Insert the key into the ignition key cylinder.

Reconnect the battery.
Any of the following conditions is met

Open and close either of all doors and
engine hood.
Any of the following conditions is
met

Close and open either of
all doors and engine hood.Any of the following conditions is met

Press the unlock button of wireless.

Insert the key into the key cylinder of driver
or passenger seat and turn the key to unlock.

Insert the key into the ignition key cylinder.

Reconnect the battery.
Any of the following conditions is met

Press unlock switch of the wireless.

Insert the key into the driver and passenger
doors key cylinders, turn the key to unlock.

Insert the key into the ignition key cylinder
and turn the key to ON.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±145
2446 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

BE0GR±04
I04055
2 5
I04146
I04147
Not turned
UNLOCK
I04148
ON OFF BE±150
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
2451 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT THEFT DETERRENT INDICATOR LIGHT OP-
ERATION
Connect the positive (+) lead from the battery terminal 2 and
negative (±) lead to terminal 5, and check that the warning light
lights up.
If operation is not as specified, replace the light control rheostat.
2. INSPECT THEFT DETERRENT INDICATOR LIGHT
CIRCUIT
(See page DI±808)
3. INSPECT THEFT DETERRENT HORN OPERATION
Connect the positive (+) lead from the battery to the terminal 1
and negative (±) lead to theft deterrent horn body, and check
that the theft deterrent horn blows.
If operation is not as specified, replace the horn.
4. INSPECT THEFT DETERRENT HORN CIRCUIT
(See page DI±804)
5. INSPECT LUGGAGE COMPARTMENT DOOR KEY
LOCK AND UNLOCK SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Not turned±No continuity
UNLOCK1 ± 2Continuity
If continuity is not as specified, replace the switch.
6. INSPECT LUGGAGE COMPARTMENT DOOR KEY
LOCK AND UNLOCK SWITCH CIRCUIT
(See page DI±794)
7. INSPECT ENGINE HOOD COURTESY SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
LOCK±No continuity
UNLOCK1 ± 2Continuity
If continuity is not as specified, replace the switch.
8. INSPECT ENGINE HOOD COURTESY SWITCH CIR-
CUIT
(See page DI±790)

± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±153
2454 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
Replace the transmitter battery with a new or normal
one and check UNLOCK±LOCK function works under
the standard operation.


The battery should be replaced by only the shops with
sufficient skill as new or normal battery is necessary.

Battery quality can be judged by checking the rem-
nant volume of the battery.
Ye s
Battery faulty.
No
Make the vehicle be in the initialized condition.
Enter into the self diagnostic mode.
If operating door control receiver in the order of 1 through 2, the mode turns to diagnostic mode.
(1) Insert the key plate in the ignition key cylinder and pull out, then insert it again and turn ignition switch
OFF " ON " OFF once within 5 seconds after pulling out.
(2) After completing the procedure within 30 seconds, turn the ignition switch OFF " ON " OFF 9 times.
HINT:
In the case that either (1) or (2) condition is not satisfied, transfer to normal mode.

When completing self diagnostic mode, turn the ignition switch ON.
LOCK and UNLOCK operation and output of luggage door opener signal are not performed under the self
diagnostic mode.
1st time 9th time ON
OFF
Transmitter battery check:
Inspection start by using self diagnostic mode:
within.
30 sec.within.
5 sec.
123 9
10
Key plate
not inseted
Key plate
inseted
Ignition
switch

BE0GO±04
I04149
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±157
2458 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control transmitter battery replace-
mentº on page BE±161.
(a) Using a screwdriver, remove the screw and cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (±) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, face the key plate of
the transmitter to the vehicle, and check the transmitter
operation when pressing transmission switch on the side
of the transmitter body.
Standard:

Remote control of vehicle door lock can be operated.

LED lights up more than once.
HINT:

The minimum operation distance differs according to op-
erator, the way of holding the transmitter, and location.

As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
(e) Install the battery (lithium battery).
(f) Install a cover so that O±ring is not distorted or slipped off.
(g) Using a screwdriver, tighten the screw.

BE0GP±09
I04154
I04155
I04156
Terminal
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±161
2462 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REPLACEMENT
1. REPLACE TRANSMITTER (LITHIUM) BATTERY
NOTICE:
Special caution should be taken for handling each compo-
nent as they are precision electronic components.
(a) Using a screwdriver, remove the screw and cover.
NOTICE:
Do not pry out the cover forcibly.
HINT:
Push the cover with a finger as shown in the illustration, so that
there becomes clearance, then pry out the cover from that
clearance.
(b) Remove the transmitter.
(c) Using a screwdriver, remove the 2 screws and cover.
(d) Remove the battery (lithium battery).
NOTICE:
Do not push the terminals with a finger.
If prying up the battery (lithium battery) forcibly to re-
move, the terminals are deformed.
(e) Install a battery (lithium battery) as shown in the illustra-
tion.
NOTICE:
Face the battery upward. Take care not to deform the termi-
nals.
(f) Check that O±ring is not distorted or slipped off, and
install the cover.
(g) Using a screwdriver, tighten the 2 screws.
NOTICE:
When the shrews are tightened loosely, it might cause
faulty contact of battery (lithium battery) and terminals.
(h) Assemble the transmitter to the key plate and the cover.
(i) Using a screwdriver, tighten the screw.