2000 LEXUS GS400 sensor

SF151±01
B08999
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part
21 (210, 15)
21 (210, 15)
VSV Connector for EVAP
Camshaft Position Sensor Connector
No.2 Vacuum Pipe
Accelerator Cable
EVAP Hose
Noise Filter
Connector
Vacuum
Hose
Throttle Position
Sensor Connector

Gasket
PS Air Hose
Engine Wire Clamp

Gasket
Oil Dipstick and
Guide for A/T
Engine Wire
Clamp
42 (420, 31)
Fuel Pressure Pulsation Damper

Gasket

O±Ring
Fuel Inlet Pipe Delivery Pipe
21 (210, 15)
Spacer
Injector Connector
O±Ring
O±Ring
Injector

Insulator

Grommet
28 (280, 21)
Engine Cover
SF±20
± SFI (2JZ±GE)INJECTOR
1486 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
COMPONENTS

SF0NB±04
B01579
± SFI (2JZ±GE)INJECTOR
SF±21
1487 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
2. REMOVE AIR INTAKE CHAMBER (See page SF±46)
3. REMOVE FUEL PRESSURE PULSATION DAMPER
(See page SF±26)
4. REMOVE DELIVERY PIPE AND INJECTORS
NOTICE:

Be careful not to drop the injectors when removing
the delivery pipe.

Pay attention to put any hung load on the injector to
and from the side direction.
(a) Disconnect the 6 injector connectors.
(b) Disconnect the camshaft position sensor connector.
(c) Disconnect the throttle position sensor connector.
(d) Disconnect the VSV connector for EVAP.
(e) Remove the 3 bolts and delivery pipe together with the 6
injectors.
(f) Pull out the 6 injectors from the delivery pipe.
(g) Remove the O±rings, grommet and insulator from each
injector.
(h) Remove the 3 spacers from the intake manifold.

SF0ND±04
B01220
New Insulator
New O±Ring
New Grommet New O±Ring
B01571
Turn
Outward
Connector
B01580
RotateUpward SF±24
± SFI (2JZ±GE)INJECTOR
1490 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL INJECTORS AND DELIVERY PIPE
(a) Install new insulator and grommet to each injector.
(b) Apply a light coat of spindle oil or gasoline to 2 new O±
rings and install them to each injector.
(c) Apply a light coat of spindle oil or gasoline on the place
where a delivery pipe touches an O±ring of the injector.
(d) While turning the injector clockwise and counterclock-
wise, push it to the delivery pipe. Install the 6 injectors.
(e) Position the injector connector outward.
(f) Place the 3 spacers in position on the intake manifold.
(g) Apply a light coat of spindle oil or gasoline on the place
where a intake manifold touches an O±ring of the injector.
(h) Place the 6 injectors together with the delivery pipe and
3 bolts in position on the intake manifold.
(i) Temporarily install the 3 bolts holding the delivery pipe to
the intake manifold.
(j) Check that the injectors rotate smoothly.
HINT:
If injectors do not rotate smoothly, the probable cause is incor-
rect installation of O±rings. Replace the O±rings.
(k) Position the injector connector upward.
(l) Connect the 6 injector connectors.
HINT:
The Nos.1, 3, 5 injector connectors and dark gray, and the
Nos.2, 4, 6 injector connectors are brown.
(m) Tighten the 3 bolts holding the delivery pipe to the intake
manifold.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(n) Connect the camshaft position sensor connector.
(o) Connect the throttle position sensor connector.
(p) Connect the VSV connector for EVAP.
2. INSTALL FUEL PRESSURE PULSATION DAMPER
(See page SF±27)
3. INSTALL AIR INTAKE CHAMBER
(See page SF±49)
4. INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.

SF0NL±05
B09506
B01608
B01982
LEXUS
Hand±Held
Tester SF±32
± SFI (2JZ±GE)THROTTLE BODY
1498 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
THROTTLE BODY
ON±VEHICLE INSPECTION
1. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
2. INSPECT SYSTEM OPERATION
(a) Check that the throttle linkage moves smoothly.
(b) Inspect the throttle control motor for operating sound.
(1) Turn the ignition switch ON.
(2) When turning the accelerator pedal position sensor
lever, check the running sound of the motor. Also,
check that there is no friction sound.
If operation is not as specified, check the throttle control motor,
wiring and ECM.
(c) Inspect the throttle position sensor and accelerator pedal
position sensor function.
(1) Connect the LEXUS hand±held tester to the DLC3.
(2) When turning the accelerator pedal position sensor
lever to the full±open position, check that the
throttle valve opening percentage (THROTTLE
POS) of the CURRENT DATA showns the standard
value.
Throttle valve opening percentage: 60 % or more
If operation is not as specified, check that the throttle position
sensor, accelerator pedal position sensor, wiring and ECM.
(d) Start the engine, and check that the Malfunction Indicator
Lamp (MIL) does not light up.
(e) Inspect the air assist system.
(1) Allow the engine to warm up to normal operating
temperature.

B09507
B01620
Ohmmeter3 (CL±)
4 (CL+)
1 (M+)
2 (M±)
B01942VCOhmmeter
E2
B01943
VC Ohmmeter
E2
± SFI (2JZ±GE)THROTTLE BODY
SF±33
1499 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(2) Turn the A/C switch ON and OFF, and check the idle
speed.
Idle speed (Transmission in neutral):
700 ± 50 rpm (A/C OFF)
750 ± 50 rpm (A/C ON)
NOTICE:
Perform inspection under condition without electrical load.
(3) With engine idling, pinch the air assist hose and
check that engine speed drops, and then returns
back up to idle speed.
If operation is not as specified, check the throttle body, wiring
and ECM.
(f) After checking the above (b) to (e), perform the diving test
and check that there is no sense of incongruity.
3. INSPECT THROTTLE CONTROL MOTOR
(a) Disconnect the throttle control motor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minal 3 (CL±) and 4 (CL+).
Resistance: 4.2 ± 5.2 W at 20°C (68°F)
(c) Using an ohmmeter, measure the resistance between ter-
minal 1 (M+) and 2 (M±).
Resistance: 0.3 ± 100 W at 20°C (68°F)
If the resistance is not as specified, replace the throttle control
motor. (See page SF±37)
(d) Reconnect the throttle control motor connector.
4. INSPECT THROTTLE POSITION SENSOR
(a) Disconnect the throttle position sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals VC and E2.
Resistance: 1.2 ± 3.2 kW at 20°C (68°F)
If the resistance is not as specified, replace the throttle position
sensor. (See page SF±37)
(c) Reconnect the throttle position sensor connector.
5. INSPECT ACCELERATOR PEDAL POSITION SEN-
SOR
(a) Disconnect the accelerator pedal position sensor con-
nector.
(b) Using an ohmmeter, measure the resistance between ter-
minals VC and E2.
Resistance: 1.2 ± 3.2 kW at 20°C (68°F)
If the resistance is not as specified, replace the accelerator ped-
al position sensor. (See page SF±37)

SF±34
± SFI (2JZ±GE)THROTTLE BODY
1500 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(c) Reconnect the accelerator pedal position sensor connec-
tor.
6. REINSTALL ENGINE COVER
Reinstall the engine cover with the 4 nuts.

SF0NM±07
B09000
Intake Air Resonator
PCV Hose
PS Air Hose
Throttle Control
Motor ConnectorThrottle Body Bracket
Throttle Position Sensor Connector
Water Bypass HoseWater Bypass Hose Engine Wire ClampAccelerator Pedal Position
Sensor Connector
Accelerator Cable
21 (210, 15)
N´m (kgf´cm, ft´lbf) : Specified torqueThrottle Body
Engine Cover
B01947
CoverAccelerator Pedal Position Sensor
Washer Plate
Throttle Control Motor
Throttle Position Sensor Bracket
x 5
± SFI (2JZ±GE)THROTTLE BODY
SF±35
1501 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
COMPONENTS

SF0NN±05
B01615
B01616
Forward
Down±Side
Diagonal(2) (1)
SF±36
± SFI (2JZ±GE)THROTTLE BODY
1502 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
3. REMOVE INTAKE AIR RESONATOR
4. REMOVE THROTTLE BODY BRACKET AND
THROTTLE BODY
(a) Disconnect the accelerator cable.
(b) Disconnect the throttle position sensor connector.
(c) Disconnect the throttle control motor connector.
(d) Disconnect the accelerator pedal position sensor con-
nector.
(e) Disconnect the engine wire clamp from the clamp bracket
of throttle body.
(f) Remove the 2 bolts and nut holding the throttle body to
the intake air connector.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(g) Remove the 4 nuts and throttle body bracket.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(h) Slightly slide the throttle body away from the intake air
connector.
NOTICE:
When putting up the throttle body, do not hold the motor
part.
(i) Disconnect the 2 water bypass hoses from the throttle
body, and remove the throttle body.
HINT:

At the time of installation, please refer to the following
items.

Connect the water bypass hose with its discrimination
mark downward.

Install the with its craw direction for (1) forward and down±
side diagonal (engine side about 45°) for (2).