2000 Lexus ES300 Owner's Manuals (in English)

INTERIOR EQUIPMENT
85
The power outlet is designed for power supply for
car accessories.
The ignition key must be in the ªACCº or ªONº position
for the power outlet to be used.
NOTICE
To prevent the fuse from being blown, do not
use the electricity over the total vehiclecapacity of 12V/120W.
To prevent the battery from being discharged,do not use the power outlet longer thannecessary when the engine is not running.
Close the power outlet lid when the poweroutlet is not in use. Inserting a foreign objectother than the appropriate plug that fits theoutlet, or allowing any liquid into the outlet maycause electrical failure or short circuits.
GLOVE BOX

INTERIOR EQUIPMENT
86
14E061

1Unlock 2Open 3Lock
To open the glove box door, pull the lever. To lock
the glove box door, insert the master key and turn it
clockwise.
With the tail lights on, the glove box light will come on
when the glove box door is open.
The trunk lid opener main switch is installed inside the
glove box. See page 105 for further information.
For the CD automatic changer, see page 254.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the glove box door closed
while driving.

INTERIOR EQUIPMENT
87
REAR CONSOLE BOX
14E059

1Upper tray 2Console box
To access the upper tray, push the lock release
button and raise the lid. To access the console box,
pull up the lock release lever and raise the lid.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the rear console box closed
while driving.

INTERIOR EQUIPMENT
88
GARAGE DOOR OPENER
The garage door opener is manufactured under
license from HomeLink and can be programmed
to operate garage doors, estate gates, security
lighting, etc.
(a) Programming HomeLink
14E063

INTERIOR EQUIPMENT
89
The
HomeLink
 has 3 buttons and can be
programmed to operate 3 separate devices.
Prepare the HomeLink
 for programming by
erasing all codes or the memorized data
programmed by the former owner. Follow the
procedure in ª(c) Erasing the garage door opener
memoryº.
1. Decide which one of the 3 buttons you want to
program. Push and hold down the button for about 20
seconds until the indicator light begins to flash. While
holding this button, follow steps ª2º and ª3º. 2. Bring the hand held garage door opener within about
25 mm (1 in.) of the button being programmed and push
the button on the hand held garage door opener. The
signal from the hand held garage door opener is sent to
the vehicle's opener.
3. When the frequency and code is registered, the
indicator light flashes rapidly. At this point, you can
release both buttons.
4. To program the remaining buttons, repeat steps ª1º
through ª3º.
If you want to replace an existing program with a new
program, select the button you want to
program. Follow
the procedure from step 1.
If the transmitter has a ªrolling code featureº, it is
necessary to program the in±garage receiver after
programming HomeLink
.
1. Locate the ªtrainingº or ªlearningº button on the
in±garage receiver and push and release this
button. Location of the button may vary by the
garage door opener manufacturer.
2. Firmly push and release the trained HomeLink

button 2 times (some garage door manufacturer
may require you to push the HomeLink button up
to 3 times) to complete the process.
The garage door should now operate when the
HomeLink
 button is pushed.

INTERIOR EQUIPMENT
90Do not use the HomeLink
 universal transmitter with
any garage door opener that lacks the safety stop and
reverse feature as required by Federal Safety
Standards. This includes any garage door opener
model manufactured before April 1, 1982.
CAUTION
When programming or operating the garage door
opener, make sure there is no one around the moving
door. It is dangerous if someone is caught.
(b) Operating the garage door opener
Push the appropriate button to activate the garage door
opener. The indicator light comes on. The garage door
opener continues to send the signal for up to 20 seconds
as long as the button is pushed.
(c) Erasing the garage door opener memory
Push and hold down the 2 outside buttons for about 20
seconds until the indicator light flashes. All memorized
data will be erased. FCC ID: CB2V94800
CANADA: 1763 102 264
This device complies with FCC Rules part 15.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference that may be received,
including interference that may cause undesired
operation. WARNING: This transmitter has
been tested and complies with FCC and
DOC/MDC rules. Changes or modifications
not expressly approved by the party
responsible for compliance could void the
user's authority to operate the device.

INTERIOR EQUIPMENT
91
CUP HOLDER
14E010

Front cup holder
To use the front cup holder, push the top of the cup
holder portion of the console box.

INTERIOR EQUIPMENT
92
14E011±2

Rear cup holder
To use the rear cup holder, pull the cup holder
portion of the console box.
The cup holder is designed for holding cups or
drink±cans securely in its holes.
CAUTION
Do not place anything else other than cups or
drink±cans on the cup holder, as such items may be
thrown about in the compartment and possibly injure
people in the vehicle during sudden braking or in an
accident.
 To reduce the chance of injury in case of an accident
or sudden stop while driving, keep the cup holder
closed when not in use.