2000 Citroen C5 engine coolant

Downloaded from www.Manualslib.com manuals search engine INJECTION
Idling - antipollution 111
Petrol injection 112
Emission standards 113 - 119
Prohibited operations : HDi 120 - 121
Safety requirements : HDi 122 - 123
Checking the fuel supply circuit 124 - 125
Checking the air supply circuit 126 - 130
Exhaust gas recycling 131 - 134
Checking turbo pressure 135 - 138
Features of injection systems 139 - 168
IGNITION
Sparking plugs 169
CLUTCH-GEARBOX
Speedometers 170
Clutch specifications 171 - 172
Gearbox and tyre specifications 173 - 174
BE4/5 gearbox controls 175 - 183
ML/5 gearbox controls 184 - 192
AL4-4HP20 gearbox controls 193 - 203
Driveshafts 204
AXLES-SUSPENSION
Wheels and tyres 205 - 211
Axle geometry 212 - 214
Front and rear axle 215 - 216Suspension 217 - 220
Steering specifications 221 - 222
BRAKES
Brake specifications 223 - 228
Handbrake adjustment 229
Bleeding and filling braking system 230 - 233
HYDRAULICS
Specifications 234 - 237
Suspension spheres 238 - 240
ELECTRICAL
Starter motors 241
Alternators 242
Charging circuit 243
AIR CONDITIONING
Quantities in R 134a aircon system 244
Special features 245
Pollen filter 246
Dryer cartridge 247 - 249
Checking oil level 250 - 251
Checking pressures 252
Air conditioning : 6FN-RFN-RLZ 253
Air conditioning circuit : XFX 254
Air conditioning circuit : RHY-RHZ 255
Air conditioning circuit : 4HX 256
INDEX
GENERAL
Identification of vehicles 1 - 4
General : Dimensions 5 - 6
Weight specifications 7 - 8
Towing specifications 9 - 10
Lifting / supporting the vehicle 11 - 14
Capacities 15 - 18
Lubricants 19 - 32
ENGINES
Engine specifications 34 - 58
Cylinder head marking / tightening
6FZ-RFN-RLZ 38
XFX 51 - 52
RHY-RLZ 55 - 56
4HX 57 - 58
Auxiliaries drive belt 59 - 68
Checking and setting valve timing 69 - 90
Power unit suspension 91 - 95
Exhaust system 96 - 100
Cooling system 101 - 107
Checking oil pressures 108
Oil filter 109
Filling and bleeding engine coolant 110

Downloaded from www.Manualslib.com manuals search engine ENGINE
81
Setting the valve timing.
Peg :
- The engine flywheel, tool [3].(From under the vehicle).
- The camshaft, tool [5].
Loosen :
- The three screws (21).
- The screw (19)of the tensioner roller (20).
- Remove the timing belt (22).
Checks.
IMPERATIVE : Just before refitting, carry out the checks below:
Check that :
- The rollers (20), (23)and the water pump turn freely (without play or tightness).
- There are no traces of oil (on camshaft or crankshaft).
- There are no leaks of coolant fluid (from water pump).
- Replace defective components (if necessary).
CHECKING AND SETTING THE VALVE TIMING
Engines : RHY - RHZ
B1EP152DB1BP282C

Downloaded from www.Manualslib.com manuals search engine ENGINE
87
Setting the valve timing.
- Turn the crankshaft to bring camshaft to its pegging point.
- Peg the crankshaft, using tool[3].
- Peg the camshaft, using tool[5].
Untighten :
- The three screws (25).
- The screw (23)of the tensioner roller (24).
- Remove the timing belt (26).
Checks.
IMPERATIVE : just prior to refitting, carry out the checks below:
Check :
- That the rollers (24) and (27)and the water pump(22) are turning freely.
(Without play and without tightness).
- Absence of traces of oil leaks (Crankshaft and camshaft sealing rings).
- Absence of leaks of coolant fluid (Water pump).
NOTE :Replace defective components(If necessary).
CHECKING AND SETTING THE VALVE TIMING
Engine : 4HX
B1EP15ADB1BP298C

Downloaded from www.Manualslib.com manuals search engine ENGINE
104
COOLING SYSTEM SPECIFICATIONS
Engine : RLZ
(1) Venting chamber
(2) Water pump
(3)Heater matrix
(4).Bleed screw, heater matrix
(5)Drain screw, cylinder block
(6) Coolant outlet housing
(7) Bleed screw, coolant outlet housing
(8) Bleed screw, top hose.
(9) Cooling radiator.
(10) Drain screw, cooling radiator
(11)Drain screw, cooling radiator.
Thermostat tightening : 1.7 ± 0.2m.daN
B1GP08JP

Downloaded from www.Manualslib.com manuals search engine ENGINE
105
COOLING SYSTEM SPECIFICATIONS
Engine : XFX
(1)Heater matrix
(2)Venting chamber
(3) Thermostat.
(4) Coolant outlet housing
(5) Coolant inlet housing
(6) Engine cooling radiator
(7) Venting chamber
(8) Bleed screw
(9) Water / oil exchanger
(10) Thermostat
(11) Thermostat(Coolant outlet housing)
(12) Thermal switch
(10). (11)and (12): Tightening 1.7 ± 0.4 m.daN
B1GP041P

Downloaded from www.Manualslib.com manuals search engine ENGINE
106
COOLING SYSTEM SPECIFICATIONS
Engines : RHY-RHZ
(1) Venting chamber
(2) Heater matrix
(3) Coolant inlet housing
(4)Exhaust gas / coolant heat exchanger
(5)Bleed screw
(6)Cylinder block drain plug
(7) Coolant outlet housing
(8) Additional heating (Option or according to version)
(9) Radiator
(10) Coolant / oil heat exchanger
B1GP08EP

Downloaded from www.Manualslib.com manuals search engine ENGINE
107
COOLING SYSTEM SPECIFICATIONS
Engine : 4HX
(10)Heater matrix
(2) Coolant inlet housing.
(3) Exhaust gas / coolant heat exchanger
(4) Bleed screw
(5)Coolant outlet housing.
(6)Additional heating (Option or according to version)
(7) Radiator
(8)Air / coolant heat exchanger
(9) Coolant / oil heat exchanger
(10) Venting chamber
B1GP08HP

Downloaded from www.Manualslib.com manuals search engine ENGINE
110
FILLING AND BLEEDING THE COOLING CIRCUIT
TOOLS
[1] Filling cylinder: 4520-T
[2]Adaptor for filling cylinder: 4222-T.
ESSENTIAL : Respect the safety and cleanliness recommendations.
- The draining and refilling operations can be carried out by means of a WINN’S coolant replacement
apparatus or similar; it is essential to follow the instructions when using this apparatus.
Filling and bleeding
- Fit the cylinder adaptor [2] 4222-Tand the filling cylinder [1] 4520 -T.
- Use the coolant to ensure protection between - 15°Cand - 37°C.
- Slowly fill the system.
NOTE :Keep the cylinder filled up (visible level).
- Close each bleed screw as soon as the coolant flows without air bubbles.
- Start the engine : Engine speed 1500 rpm.
- Maintain this speed until the third cooling cycle (cooling fans have cut in and cut out).
- Stop the engine and allow it to cool down.
- Remove the filling cylinder [1] 4520-T and the adaptor [2] 4222-T.
- Top up the system to the maximum mark, with the engine cold.
- Refit the filler cap.
E5AP1GNCB1GP00AC