2000 CHRYSLER VOYAGER key

Symptom:
P-0135 O2S HEATER FAILURE
When Monitored and Set Condition:
P-0135 O2S HEATER FAILURE
When Monitored: With the ignition key off, after the engine cools down.
Set Condition: No sensor output signal is received when the PCM powers up the sensor
heater.
POSSIBLE CAUSES
1/1 O2 SENSOR CONNECTOR DAMAGED
1/1 O2 SENSOR GND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
1/1 O2 SENSOR FAILURE
1/1 O2 SENSOR HEATER ELEMENT FAILURE
1/1 O2S HEATER FAILURE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the GLOBAL GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 Turn Ignition On (Engine Off), wait three minutes.
With the DRB , monitor the O2 Sensor voltage for a few minutes until the voltage
stabilizes between .4 and .6 volts.
With the DRB, actuate the O2 Heater Test.
Monitor O2 voltage for up to two minutes.
Is the O2 Sensor voltage still between .4 and .6 volts?All
Ye s®Go To 4
No®Go To 3
3 At this time the 1/1 O2S HEATER FAILURE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/1 O2S HEATER FAILURE reoccur?All
Ye s®Go To 4
No®1/1 O2S Heater failure no longer exists.
Perform VERIFICATION TEST VER-5A3.
62
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0137 1/2 O2 SENSOR VOLTAGE SHORTED TO GROUND
When Monitored and Set Condition:
P-0137 1/2 O2 SENSOR VOLTAGE SHORTED TO GROUND
When Monitored: With the ignition key off, after the O2 Sensor cools down; and after the
next key on provided that it is a cold start (coolant temperature less than 38 degrees C
(100.4 degrees F) and ambient temperature within 13.7 degrees C (7.2 degrees F) of coolant
temperature.
Set Condition: The Downstream O2 Sensor Signal voltage is below 0.156 volt prior to O2
Sensor Heater test (cool down period), and O2 voltage less than 0.156 volt after the key on
in the subsequent start.
POSSIBLE CAUSES
1/2 02 SENSOR VOLTAGE LOW
1/2 O2S SIGNAL CIRCUIT SHORT TO GROUND
1/2 O2S SIGNAL CKT SHORT TO GROUND CIRCUIT
1/2 O2 SENSOR DEFECTIVE
PCM DEFECTIVE (1/2 O2S)
TEST ACTION APPLICABILITY
1 Ignition Off
Turn ignition on.
With the DRB, monitor the Downstream O2 Sensor voltage for a few minutes.
Wait three minutes or until the voltage stabilizes (between 0.4 and 0.6 volt).
With the DRB, monitor the Downstream O2 Sensor voltage.
Is the Downstream O2 Sensor voltage below 0.156 volt?All
Ye s®Go To 2
No®The condition required to set this trouble code is not present at
this time.
Perform Powertrain Verification Test VER-5A.
2 Ignition Off
Disconnect the Downstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Key on.
With the DRB, monitor the Downstream O2 Sensor voltage.
Is the Downstream O2 Sensor voltage below 0.156 volts?All
Ye s®Go To 3
No®Replace the Downstream O2 Sensor.
Perform Powertrain Verification Test VER-5A.
64
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0141 1/2 O2S HEATER FAILURE
When Monitored and Set Condition:
P-0141 1/2 O2S HEATER FAILURE
When Monitored: With the ignition key off, after the engine cools down.
Set Condition: No sensor output signal is received when the PCM powers up the sensor
heater.
POSSIBLE CAUSES
1/2 O2 SENSOR CONNECTOR DAMAGED
1/2 O2 SENSOR GND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
1/2 O2 SENSOR FAILURE
1/2 O2 SENSOR HEATER ELEMENT FAILURE
1/2 O2S HEATER FAILURE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the GLOBAL GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 Turn Ignition On (Engine Off), wait three minutes.
With the DRB, monitor the O2 Sensor voltage for a few minutes until the voltage
stabilizes between .4 and .6 volts.
With the DRB, actuate the O2 Heater test.
Monitor O2 voltage for up to two minutes.
Is the O2 Sensor voltage still between .4 and .6 volts?All
Ye s®Go To 3
No®Go To 4
3 At this time the 1/2 O2S HEATER FAILURE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/2 O2S HEATER FAILURE reoccur?All
Ye s®Go To 4
No®1/2 O2S Heater failure no longer exists.
Perform VERIFICATION TEST VER-5A3.
73
DRIVEABILITY
ProCarManuals.com

Symptom:start here
P-0201 INJECTOR #1 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0201 INJECTOR #1 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR DEFECTIVE
INJECTOR #1 DRIVER CIRCUIT OPEN
INJECTOR #1 DRIVER CIRCUIT SHORTED TO GROUND
POWERTRAIN CONTROL MODULE DEFECTIVE
INJECTOR #1 DRIVER CIRCUIT SHORT TO GROUND
INJECTOR #1 DRIVER CIRCUIT SHORT TO GROUND (PCM)
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Disconnect the Injector #1 Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #1.
Is the resistance between 10.0 and 16.0 ohms?All
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
83
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0202 INJECTOR #2 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0202 INJECTOR #2 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR DEFECTIVE
INJECTOR #2 DRIVER CIRCUIT OPEN
INJECTOR #2 DRIVER CIRCUIT SHORTED TO GROUND
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Note: It may be necessary to remove the Intake Plenum in the following
steps.
Disconnect the Injector #2 Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #2.
Is the resistance between 10.0 and 16.0 ohms?All
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
86
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0203 INJECTOR #3 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0203 INJECTOR #3 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
FUEL INJECTOR #3 DEFECTIVE
INJECTOR #3 DRIVER CIRCUIT OPEN
INJECTOR #3 DRIVER CIRCUIT SHORTED TO GROUND
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Note: It may be necessary to remove the Intake Plenum in the following
steps.
Disconnect the Injector #3 Connector.
Note: Check connectors - Clear/repair as necessary.
Using an Ohmmeter, measure the resistance of Injector #3.
Is the resistance between 10.0 and 16.0 ohms?All
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
89
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0204 INJECTOR #4 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0204 INJECTOR #4 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR #4 DEFECTIVE
INJECTOR #4 DRIVER CIRCUIT OPEN
INJECTOR #4 DRIVER CIRCUIT SHORTED TO GROUND
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?ALL
Ye s®Go To 2
No®Go To 7
2Note: It may be necessary to remove the Intake Plenum in the following
steps.
Key off.
Disconnect the #4 Injector Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #4.
Is the resistance between 10.0 and 16.0 ohms?ALL
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
92
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3Note: It may be necessary to remove the Intake Plenum in the following
steps.
Disconnect the #4 Injector Connector.
Note: Check connectors - Clean/repair as necessary.
Turn ignition on.
With the DRB, actuate the Auto Shutdown Relay.
Using a Voltmeter, measure the ASD Relay Output voltage.
Does the voltage cycle high and low?ALL
Ye s®Go To 4
No®Repair the open ASD Relay Output Circuit.
Perform Powertrain Verification Test VER-5A.
4Note: It may be necessary to remove the Intake Plenum in the following
steps.
Key off.
Disconnect the Injector #4 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure across the Injector #4 Driver Circuit from the PCM to
the Injector.
Is the resistance below 5.0 ohms?ALL
Ye s®Go To 5
No®Repair the open Injector #4 Driver Circuit.
Perform Powertrain Verification Test VER-5A.
5Note: It may be necessary to remove the Intake Plenum in the following
steps.
Key off.
Disconnect the #4 Injector Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #4 Driver Circuit to ground.
Is the resistance below 5.0 ohms?ALL
Ye s®Repair the Injector #4 Control Circuit for a short to ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.ALL
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-5A.
7 Engine Running
Wiggle Wiring Harness from the Injector to the PCM.
Does the engine miss or stall?ALL
Ye s®Repair as necessary where wiggling caused the problem to
appear.
Perform Powertrain Verification Test VER-5A.
No®Go To 8
93
DRIVEABILITY
P-0204 INJECTOR #4 CONTROL CIRCUIT ÐContinued
ProCarManuals.com