Powertrain Verification Test VER-5A3 APPLICABILITY
OBDII Monitor Verification
Use this test to verify that the OBDII monitor symptom has been repaired and that the vehicle
can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for further diagnostic testing
procedures.
3. With the DRBIIIt, monitor the pre-test enabling conditions. Operate the vehicle within the
enabling conditions and allow the applicable monitor to run.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedurs. Refer to any Technical Service Bulletins that may apply.
5. If the monitor runs and the Good Trip Counter changes to one or more, the condition is no
longer present.
6. If there are no DTCs and all components are functioning properly, the repair is complete.All
Powertrain Verification Test VER-6A APPLICABILITY
LDP Monitor Verification
Use this test to verify that the LDP monitor symptom has been repaired and that the vehicle
can be returned to the customer.
NOTE: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and Transponder (ignition key).
1. Inspect the vehicle to ensure that all components are related to the repair are connected
properly.
2. If any other DTC is present, refer to the symptom list for futher diagnostic testing
procedures.
3. With the DRBIIIt, perform the LDP Monitor Test. Follow the instructions on the DRBIIIt
screen.
4. If the DTC resets, or the OBDII monitor fails after running, or if any other symptom or DTC
is present, return to the symptom list and perform the appropriate diagnostic testing
procedures. Refer to any Technical Service Bulletins that mat apply.
5. If the monitor runs and test does not fail, the condition is no longer present.
6. If there are no DTCs and all components are functioning properly, the repair is complete.All
321
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com
Powertrain Verification Test VER-7A APPLICABILITY
SKIS Verfication
Use this test to verify that SKIM system symptom has been repaired and that the vehicle can
be returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and SKIM
modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programmig information for the PCM, SKIM
and the Transponder (ignition key).
1.Inspect the vehicle to ensure that all components related to the repair are connected properly.
2. Inspect the engine oil for fuel contamination. Replace the oil and filter as necessary.
3. Start the engine.
4. Run the engine for one warm-up cycle to verify proper operation. With the DRBIIIt, confirm
that no DTCs are present and that all components are functioning properly. If the DTC is still
present refer to any Technical Service Bulletins that may apply.
5. If a different DTC(s) is present, refer to the symtom list and perform diagnostic testing as
necessary. If there are no DTCs present and all components are functioning correctly, repair is
now complete.All
322
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com
RADIATOR FAN NO 2 - BLACK 2 WAYCAV CIRCUIT FUNCTION
1 C23 12DG LOW SPEED RADIATOR FAN RELAY OUTPUT
2 Z1 12BK GROUND
RADIATOR FAN RELAY - BLACK 4 WAYCAV CIRCUIT FUNCTION
1 Z1 14BK GROUND
2 K173 14LG/DB RADIATOR FAN RELAY CONTROL
3 C23 12DG LOW SPEED RADIATOR FAN RELAY OUTPUT
4 A16 12GY FUSED B(+)
SENTRY KEY IMMOBILIZER MODULE - BLACK 6 WAYCAV CIRCUIT FUNCTION
1 F41 20PK/WT FUSED B(+)
2 Z2 20BK GROUND
3 F87 20WT/BK FUSED IGNITION SWITCH OUTPUT (ST-RUN)
4- -
5 D2 20WT/BK CCD BUS (-)
6 D1 20VT/BR CCD BUS (+)
THROTTLE POSITION SENSOR (2.0L) - BLACK 3 WAYCAV CIRCUIT FUNCTION
1 K4 18BK/LB SENSOR GROUND
2 K22 18OR/DB THROTTLE POSITION SENSOR SIGNAL
3 K6 18VT/WT 5V SUPPLY
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
351
CONNECTOR PINOUTS
ProCarManuals.com
