2000 Acura Integra Hatchback Owner's Manual

Engin
e Oi l
1. Run the engine until it reaches
normal operating temperature,
then shut it off.

2. Open the hood and remove the

engine oil fill cap. Remove the oil drain bolt and washer from thebottom of the engine. Drain the oil
into an appropriate container.

3. Remove the oil filter and let the

remaining oil drain. A special
wrench (available from your Acura dealer) is required to remove the
filter.

4. Install a new oil filter according to

instructions that come with it.

Maintenanc e
WASHE
R

OI L DRAI N BOL T OI
L FILTE R

Engin
e Oi l

5. Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to: 3 3 Ibf .
f t (4 4 N .
m , 4. 5 kgf .
m )

6. Refill the engine with the recom-

mended oil.
Engine oil change capacity
(including filter):

(SE, LS, GS)
4.
0 U S q t (3. 8
, 3.3 Im p qt )

(GS-R,Type-R)
4.
2 U S q t (4. 0
, 3.5 Im p qt ) 7. Replace the engine oil fill cap.
Start the engine. The oil pressure
indicator light should go out within
five seconds. If it does not, turn off
the engine and reinspect your
work.
8. Let the engine run for several

minutes and check the drain bolt
and oil filter for leaks.

9. Turn off the engine, let it sit for

several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.

Improper disposal of engine oil can be harmful to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

Maintenance

NOTIC
E

Coolin
g Syste m

Addin g Engin e Coolan t
If the coolant level in the reserve
tank is at or below the MIN line, add coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and50 percent water. Never add straight
antifreeze or plain water. Always use Genuine Honda
Antifreeze/Coolant. If it is not
available, you may use another
major-brand non-silicate coolant as a
temporary replacement. Make sure it is a high-quality coolant
recommended for aluminum engines.
However, continued use of any non-
Honda coolant can result in
corrosion, causing the coolingsystem to malfunction or fail. Have
the cooling system flushed and refilled with Honda antifreeze/
coolant as soon as possible. If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.

Maintenanc e
Removing the radiator cap

while the engine is hot can
cause the coolant to spray out,
seriously scalding you.

Always let the engine and radiator cool down before

removing the radiator cap.

MI
N
MAX
RESERV E TAN K

Coolin
g Syste m

1. Make sure the engine and
radiator are cool.

2. Turn the radiator cap counter-

clockwise, without pressing down on it, until it stops. This relieves
any pressure remaining in the
cooling system.

3. Remove the radiator cap by

pushing down and turningcounterclockwise.

4. The coolant level should be up to

the base of the filler neck. Add
coolant if it is low.

5. Put the radiator cap back on.

Tighten it fully.

6. Pour coolant into the reserve tank.

Fill it to halfway between the MAXand MIN marks. Put the cap back
on the reserve tank.

CONTINUED

Maintenanc e
RESERV
E TAN K
RADIATO
R CA P

Coolin
g Syste m
Do not add any rust inhibitors or other additives to your car's cooling
system. They may not be compatible
with the coolant or engine compo-
nents.

Replacin g Engin e Coolan t
The cooling system should be completely drained and refilled with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance done by a skilled mechanic. 1. Turn the ignition ON (II). Slidethe heater temperature control
lever to maximum heat. Turn the ignition off.
2. Open the hood. Make sure the
engine and radiator are cool to the touch.
3. Remove the radiator cap. 4. Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the splash guard. Remove the drainbolt and washer from the engine block.
Maintenanc e DRAI
N PLU G
DRAI
N
BOL T

Coolin
g Syste m
5. Remove the reserve tank from itsholder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.
6. When the coolant stops draining,
tighten the drain plug at the
bottom of the radiator. Put a new
washer on the drain bolt, then reinstall the drain bolt in theengine block. Tighten it securely.
Tightening torque:
58 Ibf .
ft (78 N .
m , 8.0 kgf .
m)
7. Mix the recommended antifreeze
with an equal amount of purified
or distilled water in a clean
container. The cooling system
capacity is:

With 5-speed manual transmission:

(SE,
LS,
GS)

1.16 US gal (4.4 , 0.97 Imp gal)
(GS-R, Type-R)
1.24 US gal (4.7 , 1.03 Imp gal)
With automatic transmission:
1.24 US gal (4.7 , 1.03 Imp gal)
8. Pour coolant into the radiator up
to the base of the filler neck.
9. Start the engine and let it run for
about 30 seconds. Then turn off
the engine.

CONTINUED

Maintenanc e

HOLDE
R RESERV
E
TAN K CA P
RESERV
E TAN K
Fill u p t o her e
FILLE
R NEC K

Coolin
g Syste m

10.Fill the radiator with coolant up to
the base of the filler neck.

11.Fill the reserve tank to the MAX

mark. Install the reserve tank cap.

12.Install the radiator cap, and

tighten it to the first stop.

13.Start the engine and let it run until

the radiator cooling fan comes on at least twice. Then stop the
engine.

14.Remove the radiator cap. Fill the

radiator with coolant up to the
base of the filler neck.

15.Start the engine and hold it at

1,500 rpm until the radiator fan
comes on. Turn off the engine. Check the coolant level in the
radiator and add coolant if needed.

16.Install the radiator cap, and

tighten it fully.

17.If necessary, fill the reserve tank

to the MAX mark. Install thereserve tank cap.

Maintenanc e

Windshiel
d Washer s

Check the level in the windshield
washer reservoir at least monthly during normal usage. In bad weather,
when you use the washers often, check the level every time you stop
for fuel. This reservoir supplies the
windshield and rear window washers.
The windshield washer reservoir islocated behind the driver's side
headlight. Check the reservoir's fluid
level by removing the cap and
looking at the level gauge attached
to the cap.
Fill the reservoir with a good-quality
windshield washer fluid. This increases the cleaning capability and
prevents freezing in cold weather. When you refill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer fluidon a clean cloth. This will help to
condition the blade edges.

Do not use engine antifreeze or a vinegar/water solution in the
windshield washer reservoir.
Antifreeze can damage your car's paint, while a vinegar/water solution can
damage the windshield washer pump.
Use only commercially-available
windshield washer fluid.

Maintenance

NOTIC
E

WINDSHIEL
D WASHE R RESERVOI R
LEVE L GAUG E