1999 YAMAHA YZF-R7 brake light

CHAPTER 6
ELECTRONIC FUEL
INJECTION
ELECTRONIC FUEL INJECTION ............... 6-1
CHAPTER 7
CHASSIS
FRONT WHEEL AND BRAKE DISCS ........ 7-1
REAR WHEEL, BRAKE DISC, AND
REAR WHEEL SPROCKET ........................ 7-9
FRONT AND REAR BRAKES .................. 7-15
HYDRAULIC CLUTCH ............................. 7-43
FRONT FORK .......................................... 7-55
HANDLEBARS ......................................... 7-67
STEERING HEAD .................................... 7-72
REAR SHOCK ABSORBER
ASSEMBLY ............................................. 7-76
SWINGARM AND DRIVE CHAIN ........... 7-80
CHAPTER 8
ELECTRICAL
ELECTRICAL COMPONENTS ................... 8-1
SWITCHES ................................................ 8-2
CHECKING THE SWITCHES ..................... 8-3
CHECKING THE BULBS AND
BULB SOCKETS ........................................ 8-4
IGNITION SYSTEM ................................... 8-7
ELECTRIC STARTING SYSTEM ............. 8-12
CHARGING SYSTEM .............................. 8-16
LIGHTING SYSTEM ................................ 8-19
SIGNALING SYSTEM ............................. 8-21
COOLING SYSTEM ................................. 8-24
ELECTRONIC FUEL INJECTION
SYSTEM .................................................. 8-28
ELECTRICAL CONTROL SYSTEM ......... 8-30

1 - 15
MOTORCYCLE CARE AND STORAGE
Care
The exposure of its technology makes
a motorcycle charming but also vulner-
able. Although high-quality compo-
nents are used, they are not all rust-
resistant. While a rusty exhaust pipe
may remain unnoticed on a car, it does
look unattractive on a motorcycle. Fre-
quent and proper care, however, will
keep your motorcycle looking good, ex-
tend its life and maintain its perfor-
mance. Moreover, the warranty states
that the vehicle must be properly taken
care of. For all these reasons, it is rec-
ommended that you observe the fol-
lowing cleaning and storing
precautions.Before cleaning
1. Cover up the muffler outlet with a
plastic bag.
2. Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug caps, are tightly in-
stalled.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-
ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.Cleaning
After normal useRemove dirt with warm water, a neutral
detergent and a soft clean sponge,
then rinse with plenty of clean water.
Use a tooth or bottle brush for hard-to-
reach parts. Tougher dirt and insects
will come off more easily if the area is
covered with a wet cloth for a few min-
utes before cleaning.
MOTORCYCLE CARE AND STORAGE
ECA00010
CAUTION:
lAvoid using strong acidic
wheel cleaners, especially on
spoked wheels. If you do use
such products for hard-to-re-
move dirt, do not leave it on any
longer than instructed, then
thoroughly rinse it off with wa-
ter, immediately dry the area
and apply a corrosion protec-
tion spray.
lImproper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.
lDo not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
lDo not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the fol-
lowing areas: seals (of wheel
bearings, swingarm bearings,
forks and brakes), electric com-
ponents (couplers, connectors,
instruments, switches and
lights), breather hoses and
vents.
lFor motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure they do not
leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
lDo not rub the frame, swingarm
and other similar matte metal
parts with a cloth (neither one
dampened with solvents or
gasoline nor a dry one), as this
may deteriorate their finish.
Wash off dirt with water only.
For hard-to-remove dirt, add a
mild detergent and rub only
lightly.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads in the winter are extremely corro-
sive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads. (Salt sprayed in the
winter may remain on the roads well
into spring.)

ELECTRICAL SPECIFICATIONSSPEC
2 - 15
ELECTRICAL SPECIFICATIONS
Item Standard Limit
System voltage12 V ----
Ignition system
Ignition system type C.D.I. ----
Ignition timing 5˚ BTDC at 1,100 r/min ----
Advanced timing 55˚ BTDC at 5,000 r/min ----
Advancer type Throttle position sensor and electrical ----
Pickup coil resistance/color 421 ~ 569 W / Gy–B ----
C.D.I. unit model (manufacturer) F8T19371 (MITSUBISHI) ----
Ignition coils
Model (manufacturer) F6T549 (MITSUBISHI) ----
Minimum ignition spark gap 6 mm (0.24 in) ----
Primary coil resistance 0.16 ~ 0.21 W ----
Secondary coil resistance 5.0 ~ 6.8 kW ----
Throttle position sensor standard
resistance4 ~ 6 kW----
Charging system
System type AC magneto ----
Model (manufacturer) F4T254 (MITSUBISHI) ----
Nominal output 14 V / 22.5 A at 5,000 r/min ----
Stator coil resistance 0.38 ~ 0.46 W at 20˚C (68˚F) ----
Rectifier/regulator
Regulator type Semiconductor-short circuit ----
Model SH650D-11 (SHINDENGEN) ----
No-load regulated voltage 14.1 ~ 14.9 V ----
Capacity 18 A ----
Withstand voltage 200 V ----
Battery
Battery type GT9B-4 ----
Battery voltage/capacity 12V / 8AH ----
Headlight typeHalogen bulb
Indicator light type ´ quantityLED ´ 5
Bulbs (voltage/wattage ´ quantity)
Headlight R. 12 V 60 W ´ 1 / L. 12 V 51 W ´ 1 ----
Auxiliary light 12 V 5 W ´ 2 ----
Tail/brake light 12 V 5 W / 21 W ´ 1 ----
Front turn signal light 12 V 21 W ´ 2 ----
Rear turn signal light 12 V 21 W ´ 2 ----
Meter light 12 V 1.4 W ´ 2 ----

2 - 26
SPEC
CABLE ROUTING
1Front turn signal coupler
2Auxiliary light lead
3Headlight lead
4Throttle cable
5Left handlebar switch lead
6Clutch hose
7Front brake hose
8Right handlebar switch lead
9Main switch lead
CABLE ROUTING

2 - 31
SPEC
KPickup coil lead
LStator coil lead
MSpeed sensor lead
NSidestand switch lead
OOil level switch lead
PCoolant reservoir breather hose
QWire harness
RWire harness lead (to fall detection
switch coupler)
SWire harness lead (to fuse box)
TStarter motor leadUNeutral switch lead
VGround lead
WCoolant temperature sensor coupler
XThrottle cable
Route the wire harness in front of the ignition coils.
õBe sure that there is no slack in the tail/brake light lead
and rear turn signal leads below the rear fender panel.
‚Align the portions of the wire harness, ground lead and
starter motor lead marked with white tape with the lead
holder.
CABLE ROUTING

3 - 7
CHK
ADJ

Order Job/Part Q’ty Remarks
Removing the rear cowling
Remove the parts in the order listed.
1 Rear fender 1
2 Rear fender panel 1
3 Tail/brake light connector 2 Disconnect.
4 Rear turn signal connector 4 Disconnect.
5 Rear cowling 1
For installation, reverse the removal
procedure.
COWLINGS

3 - 37
CHK
ADJADJUSTING THE REAR BRAKE/
CHECKING THE BRAKE FLUID LEVEL
ACHTUNG:CAUTION:
After adjusting the brake pedal position,
make sure that there is no brake drag.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
3. Adjust:
• rear brake light switch
Refer to “ADJUSTING THE REAR
BRAKE LIGHT SWITCH”.
EB304020
CHECKING THE BRAKE FLUID LEVEL
1. Stand the motorcycle on a level surface.
NOTE:
• Place the motorcycle on a suitable
stand.
• Make sure that the motorcycle is
upright.
2. Check:
• brake fluid level
Below the minimum level mark a ®
Add the recommended brake fluid to
the proper level.
Front brake
õRear brake
WARNINGWARNING
• Use only the designated brake fluid.
Other brake fluids may cause the rub-
ber seals to deteriorate, causing leak-
age and poor brake performance.
• Refill with the same type of brake fluid
that is already in the system. Mixing
brake fluids may result in a harmful
chemical reaction, leading to poor
brake performance.
• When refilling, be careful that water
does not enter the brake fluid reser-
voir. Water will significantly lower the
boiling point of the brake fluid and
could cause vapor lock.
ACHTUNG:CAUTION:
Brake fluid may damage painted sur-
faces and plastic parts. Therefore,
always clean up any spilt brake fluid
immediately.
NOTE:
In order to ensure a correct reading of the
brake fluid level, make sure that the top of
the brake fluid reservoir is horizontal.
Recommended brake fluid
DOT 4

õ

3 - 38
CHK
ADJCHECKING THE BRAKE PADS/
ADJUSTING THE REAR BRAKE LIGHT SWITCH
EB304032
CHECKING THE BRAKE PADS
The following procedure applies to all of
the brake pads.
1. Operate the brake.
2. Check:
• front brake pad
• rear brake pad
Brake pad wear limit a
Wear limit reached ® Replace the
brake pads as a set.
Refer to “FRONT AND REAR BRAKES”
in chapter 7.
Front brake
õRear brake
Brake pad wear limit
0.5 mm (0.02 in)

õ
EB304050
ADJUSTING THE REAR BRAKE LIGHT
SWITCH
NOTE:
• The rear brake light switch is operated
by movement of the brake pedal.
• The rear brake light switch is properly
adjusted when the brake light comes
on just before the braking effect starts.
1. Check:
• rear brake light operation timing
Incorrect ® Adjust.
2. Adjust:
• rear brake light operation timing
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Hold the main body 1 of the rear
brake light switch so that it does not
rotate and turn the adjusting nut 2 in
direction a or b until the rear brake
light comes on at the proper time.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
Direction aBrake light comes on
sooner.
Direction bBrake light comes on
later.