1999 YAMAHA YZF-R7 brake light

7 - 8
CHASFRONT WHEEL AND BRAKE DISCS
3. Adjust:
• front wheel static balance
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Install a balancing weight 1 onto the
rim exactly opposite the heavy spot
“X”.
NOTE:
Start with the lightest weight.
b. Turn the front wheel 90˚ so that the
heavy spot is positioned as shown.
c. If the heavy spot does not stay in that
position, install a heavier weight.
d. Repeat steps (b) and (c) until the front
wheel is balanced.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
4. Check:
• front wheel static balance
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Turn the front wheel and make sure
that it stays at each position shown.
b. If the front wheel does not remain
stationary at all of the positions,
rebalance it.
s s s s s s s s s s s s s s s s s s s s s s s s s s s

7 - 42
CHASFRONT AND REAR BRAKES
2. Fill:
• brake fluid reservoir
WARNINGWARNING
• Use only the designated brake fluid.
Other brake fluids may cause the rub-
ber seals to deteriorate, causing leak-
age and poor brake performance.
• Refill with the same type of brake fluid
that is already in the system. Mixing
brake fluids may result in a harmful
chemical reaction, leading to poor
brake performance.
• When refilling, be careful that water
does not enter the reservoir. Water
will significantly lower the boiling
point of the brake fluid and could
cause vapor lock.
ACHTUNG:CAUTION:
Brake fluid may damage painted sur-
faces and plastic parts. Therefore,
always clean up any spilt brake fluid
immediately.
3. Bleed:
• brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
Recommended brake fluid
DOT 4
4. Check:
• brake fluid level
Below the minimum level mark a ®
Add the recommended brake fluid to
the proper level.
Refer to “CHECKING THE BRAKE
FLUID LEVEL” in chapter 3.
5. Adjust:
• brake pedal position
Refer to “ADJUSTING THE REAR
BRAKE” in chapter 3.
6. Adjust:
• rear brake light operation timing
Refer to “ADJUSTING THE REAR
BRAKE LIGHT SWITCH” in chapter 3.

8 - 1
–+ELEC

ELECTRICAL COMPONENTS
EB800000
ELECTRICAL
ELECTRICAL COMPONENTS
1
Wire harness
2
Main switch
3
Front brake light switch
4
Ignition coils
5
Clutch switch
6
Throttle position sensor
7
Intake air temperature sensor
8
Intake air pressure sensor
9
Atmospheric pressure sensor
0
Turn signal relay
A
Relay unit
B
ECU
C
CDI unit
D
Fuse box
E
Fall detection switch
F
Starter relay
G
Main fuse
H
Main relay
I
Battery
J
Rectifier/regulator
K
Rear brake light switch
L
Neutral switch
M
Speed sensor
N
Sidestand switch
O
Stator coil assembly
P
Oil level switch
Q
Pickup coil
R
Radiator fan
S
Horn
T
Coolant temperature
sender
U
Thermo switch
V
Camshaft sensor
8

8 - 3
–+ELEC

CHECKING THE SWITCHES
EB801010
CHECKING THE SWITCHES
Check each switch for damage or wear, proper connections, and also for continuity between
the terminals. Refer to “CHECKING SWITCH CONTINUITY”.
Damage/wear
® Repair or replace the switch.
Improperly connected ® Properly connect.
Incorrect continuity reading ® Replace the switch.
1Main switch
2Light switch
3Pass switch
4Dimmer switch
5Turn signal switch6Horn switch
7Clutch switch
8Engine stop switch
9Start switch
0Front brake light switchAOil level switch
BRear brake light switch
CFuse
DNeutral switch
ESidestand switch
1L/YL/B
LL/R
R
Br/L
OFF
ONP
L/RLBr/LRL/YL/B
3
4
5
Br/WR/YPLB
Dg Y
G Ch
B/YL/YPASS—
R/YY
67
YG
—BP
(BLUE)
(BLACK)
(BLACK)
R/WBr
R/BB
G/YL/W
B
B
G/YBr
OFF
ChBr/WDg
8R/WR/B
9
0—L/WB
2R/YL•
C
E
(BLUE)
B
B
B D
(BROWN)
Sb
A
W
L/YB/Y
L/YB/Y

8 - 4
–+ELECCHECKING THE BULBS AND BULB SOCKETS
EB801020
CHECKING THE BULBS AND
BULB SOCKETS
Check each bulb and bulb socket for dam-
age or wear, proper connections, and also
for continuity between the terminals.
Damage/wear ® Repair or replace the
bulb, bulb socket or both.
Improperly connected ® Properly con-
nect.
Incorrect continuity reading ® Repair or
replace the bulb, bulb socket or both.
TYPES OF BULBS
The bulbs used on this motorcycle are
shown in the illustration on the left.
• Bulbs A and B are used for headlights
and usually use a bulb holder which must
be detached before removing the bulb.
The majority of these bulbs can be
removed from their respective socket by
turning them counterclockwise.
• Bulb C is used for turn signal and tail/
brake lights and can be removed from the
socket by pushing and turning the bulb
counterclockwise.
• Bulbs
D and E are used for meter and
indicator lights and can be removed from
their respective socket by carefully pulling
them out.
CHECKING THE CONDITION OF THE BULBS
The following procedure applies to all of
the bulbs.
1.Remove:
• bulb

8 - 19
–+ELECLIGHTING SYSTEM
EB805000
LIGHTING SYSTEM
CIRCUIT DIAGRAM
B
(BLACK) (DARK GRAY)
(BLACK)B
L
B
L
K
WWW
86
7RR
Br
BBRR
L/W BrL/W
RR
R
B
B
BBB
B
R
WWW(BLACK)
L/W
B
R/B
R/L
G/B
R/L
L/W
B (BLUE)
Gy
Gy/B
B
B(BLUE)
Gy
B
Br
G
L/R
B
Br
G L/R
B
Br/W
Br
B
B
B
B
L/WBr
R/W
G/Y R/W
B/WB/L(GRAY)
(BROWN)
h
Br
YB
BBr
Y (BROWN) (BROWN)
R/YLBr/WP
B(BLUE) (BLUE)(BLACK) (BLACK)
Br
BBR/WR/B
Y
P
ON OFF
R
RL/R
LBr/L
B
R/L
G/W(BLACK)
R/L R/BR/G L/R(GREEN)
(BLACK) (BLACK)(BLACK)(BLACK)
O Gy
B
Br/G
B Br
L/G W/G
Y/G
BYL
B
B
G
Ch Dg
BL/W
L/R
R/BB/Y
L/YSb
R/L R/B
Br/WB1G/W B/L
L/Y
W
B/L
W/B L/YB/L
W/YL/Y
L/Y
Br L
R
Br/LR
Br/L
L/W
L/Y
Br
L/W
L/Y L/B
L L/R
B L/Y
L/R LB B BB
W
WW
W
WW
B
BB
B
B B1
B
BB
B
B
B/YL/Y
B/YL/Y
R/Y
L P
B Br/WDg
ChB/YYG
L/Y
Ch
B/YDg
G
L/YY
B
R
G
B/L
YLWBYPBL
GBB/W
(BLACK)YB
BCh
(BLACK)BDg
B
(GRAY)(BLACK)
(BLACK)
(BLACK) (GRAY)
(GRAY)
(GRAY)
(GRAY) (GRAY)B/W B/L
B/L B/L
W/LP/B Y/L
R
B
PASS
(BLACK)
(BLACK)ChB
(BLACK)DgB
N
B(BLACK)B
(BLACK) (BLACK)
O/G B(BLACK) (BLACK)
L
R/L G/B
M
R/L L/B
N
R/LR/L O/B
OY
Y/R C YG/R C GBr/R C BrGy/R C Gy
R R/LRRRRY
P
RG G(BROWN)
Q
RBr Br
Gy(DARK GRAY)R(GRAY)
R
R/YLg/Y
R/Y Lg/Y R/WB/L
R/Y
R
Y/L
B
L/R
YL/R
Gy/B
Gy
G/WB1
W/Y
W1
L/R B/L
YLW/B
Y/L W/L
P/W P/LR/Y
Br/W R/W
Lg/YL/W B/W
R/L
R/B L/WW G
Lg
L/R L/BSb
B/Y B B/R L/Y
RBR
R/G
4
BL/Y
BB
Br/L
BrBrL
B
B
B
B
BR/GB1
B
Y
B
R/WR/B
R/GR/BL/RR/L
Br
G/WR/L
L/YW/BB/L
GyGy/B
R/L
L/R
L/W
B/LL
B
Br/W
Br
Y
LPWP
B2
B2
R PB
(BLACK)
B3
B3W2
Y/G L/GBr/G Br/R
Gy/R
BrBrO/B
G/Y L/B G/B G/R
Y/R
W/G Y/B R/B
O/B
R/L
L/B
GyO
O Lg/R
B
B
B
BB Gy
Gy/G Gy/G Gy/G
O/G O/GO/G
Gy GyGy/G
Br/G
W/G
Y/G
L/G
Br
WW/YB/L
L/Y
Lg/RG/Y W/YL/R
Y/B
L/YBSb
Sb
R/GG/WWYChL
W
BrP
P G Y Ch Dg B
Dg
B
BBBB
B
Dg
ChBr
LR/Y
L/Y B/Y
Br/LBr/LBr/L
BrR/YR/W
B2
Gy
Gy/BB3
R/B
G/B
L/B
O/B
Gy/R
Lg/RY/R
G/R
Br/R
R/W
R/Y
Lg/Y
W1
W2
(BLACK)
(BLACK)
(BLACK)
(BLACK) (GRAY)
B
L
B
B/L
Br/W
B/LG/W
S
T
U
V W J
Z
R/G
B L/Y
W/YG/Y W Y/B
Br
G/WLg/R Lg Y
ChDg
L
gff e dc b a` ] \[ FE DC
I
G
H
X
j k
l
m
n
op
i w
v u

t s
r qBA@Br9 5 3 2
1
Œ

 
£¢ ¤
¥
¦xy

(BLACK)
Y
L/W
Y/B
G/Y
Y/L
W/L
P/BR
B3 W/B
B/L
L
Y
P/W
P/L
Br
G/W
B/W
W/Y
Br
B2
|
~
z } {
L/Y
A
A
A
A
AA
AAAA
A C
A
A
A
A A
A
P/LP/W
BB/L BB/L
DL DL
C
W/LP/B
WIRE HARNESS SUB LEAD
B/L B/L
BB
R/L R/L L
R/L R/L L
LRR
LR
R(GRAY)
(GRAY)
WIRE HARNESS SUB LEADY/R
Br/RP/W
G/R Gy/R P/L
WYBr
PG
Gy(BLACK)
(BLACK)
WIRE HARNESS SUB LEAD HEADLIGHT AND METER SUB-WIRE HARNESS
(BLACK)
(BLACK)
WIRE HARNESS
Y W/Y G/WG/W
R/G L G/Y Dg
Br
GY
G L/YW/Y
L/Y BBr
B W Y/B Lg Lg/RCh L/R
L/R
G/Y
R/GDg
L
Lg/R
Lg
W
Y/B ChA
BC
D
D R/L D R/L D R/L D
R
B1
Br/G
W/G
Y/G
L/G
Br
1Main switch
5Battery
6Main fuse
dHigh beam indicator light
fMeter light
jHeadlight
oTail/brake light
sLights switch
tPass switch
uDimmer switch
¢Headlight fuse

8 - 21
–+ELECSIGNALING SYSTEM
EB806000
SIGNALING SYSTEM
CIRCUIT DIAGRAM
B
(BLACK) (DARK GRAY)
(BLACK)B
L
B
L
K
WWW
86
7RR
Br
BBRR
L/W BrL/W
RR
R
B
B
BBB
B
R
WWW(BLACK)
L/W
B
R/B
R/L
G/B
R/L
L/W
B (BLUE)
Gy
Gy/B
B
B(BLUE)
Gy
B
Br
G
L/R
B
Br
G L/R
B
Br/W
Br
B
B
B
B
L/WBr
R/W
G/Y R/W
B/WB/L(GRAY)
(BROWN)
h
Br
YB
BBr
Y (BROWN) (BROWN)
R/YLBr/WP
B(BLUE) (BLUE)(BLACK) (BLACK)
Br
BBR/WR/B
Y
P
ON OFF
R
RL/R
LBr/L
B
R/L
G/W(BLACK)
R/L R/BR/G L/R(GREEN)
(BLACK) (BLACK)(BLACK)(BLACK)
O Gy
B
Br/G
B Br
L/G W/G
Y/G
BYL
B
B
G
Ch Dg
BL/W
L/R
R/BB/Y
L/YSb
R/L R/B
Br/WB1G/W B/L
L/Y
W
B/L
W/B L/YB/L
W/YL/Y
L/Y
Br L
R
Br/LR
Br/L
L/W
L/Y
Br
L/W
L/Y L/B
L L/R
B L/Y
L/R LB B BB
W
WW
W
WW
B
BB
B
B B1
B
BB
B
B
B/YL/Y
B/YL/Y
R/Y
L P
B Br/WDg
ChB/YYG
L/Y
Ch
B/YDg
G
L/YY
B
R
G
B/L
YLWBYPBL
GBB/W
(BLACK)YB
BCh
(BLACK)BDg
B
(GRAY)(BLACK)
(BLACK)
(BLACK) (GRAY)
(GRAY)
(GRAY)
(GRAY) (GRAY)B/W B/L
B/L B/L
W/LP/B Y/L
R
B
PASS
(BLACK)
(BLACK)ChB
(BLACK)DgB
N
B(BLACK)B
(BLACK) (BLACK)
O/G B(BLACK) (BLACK)
L
R/L G/B
M
R/L L/B
N
R/LR/L O/B
OY
Y/R C YG/R C GBr/R C BrGy/R C Gy
R R/LRRRRY
P
RG G(BROWN)
Q
RBr Br
Gy(DARK GRAY)R(GRAY)
R
R/YLg/Y
R/Y Lg/Y R/WB/L
R/Y
R
Y/L
B
L/R
YL/R
Gy/B
Gy
G/WB1
W/Y
W1
L/R B/L
YLW/B
Y/L W/L
P/W P/LR/Y
Br/W R/W
Lg/YL/W B/W
R/L
R/B L/WW G
Lg
L/R L/BSb
B/Y B B/R L/Y
RBR
R/G
4
BL/Y
BB
Br/L
BrBrL
B
B
B
B
BR/GB1
B
Y
B
R/WR/B
R/GR/BL/RR/L
Br
G/WR/L
L/YW/BB/L
GyGy/B
R/L
L/R
L/W
B/LL
B
Br/W
Br
Y
LPWP
B2
B2
R PB
(BLACK)
B3
B3W2
Y/G L/GBr/G Br/R
Gy/R
BrBrO/B
G/Y L/B G/B G/R
Y/R
W/G Y/B R/B
O/B
R/L
L/B
GyO
O Lg/R
B
B
B
BB Gy
Gy/G Gy/G Gy/G
O/G O/GO/G
Gy GyGy/G
Br/G
W/G
Y/G
L/G
Br
WW/YB/L
L/Y
Lg/RG/Y W/YY/B
L/YBSb
Sb
R/GG/WWYChL
W
BrP
P G Y Ch Dg B
Dg
B
BBBB
B
Dg
ChBr
LR/Y
L/Y B/Y
Br/LBr/LBr/L
BrR/YR/W
B2
Gy
Gy/BB3
R/B
G/B
L/B
O/B
Gy/R
Lg/RY/R
G/R
Br/R
R/W
R/Y
Lg/Y
W1
W2
(BLACK)
(BLACK)
(BLACK)
(BLACK) (GRAY)
B
L
B
B/L
Br/W
B/LG/W
S
T
U
V W J
Z
R/G
B L/Y
W/YG/Y W Y/B
Br
G/WLg/R Lg Y
ChDg
L
gf f e dc b a` ] \[ FE DC
I
G
H
X
j k
l
m
n
op
i w
v u

t s
r qBA@Br9 5 3 2
1
Œ

 
£¢ ¤
¥
¦xy

(BLACK)
Y
L/W
Y/B
G/Y
Y/L
W/L
P/BR
B3 W/B
B/L
L
Y
P/W
P/L
Br
G/W
B/W
W/Y
Br
B2
|
~
z } {
L/Y
A
A
A
A
AA
AAAA
A C
A
A
A
A A
A
P/LP/W
BB/L BB/L
DL DL
C
W/LP/B
WIRE HARNESS SUB LEAD
B/L B/L
BB
R/L R/L L
R/L R/L L
LRR
LR
R(GRAY)
(GRAY)
WIRE HARNESS SUB LEADY/R
Br/RP/W
G/R Gy/R P/L
WYBr
PG
Gy(BLACK)
(BLACK)
WIRE HARNESS SUB LEAD HEADLIGHT AND METER SUB-WIRE HARNESS
(BLACK)
(BLACK)
WIRE HARNESS
Y W/Y G/WG/W
R/G L G/Y Dg
Br
GY
G L/YW/Y
L/Y BBr
B W Y/B Lg Lg/RCh L/R
L/R
G/Y
R/GDg
L
Lg/R
Lg
W
Y/B ChA
BC
D
D R/L D R/L D R/L D
R
B1
Br/G
W/G
Y/G
L/G
Br
L/R
1Main switch
5Battery
6Main fuse
0Relay unit
ZNeutral switch
\Fuel level indicator light
]Warning light (oil level indicator)
^Neutral indicator light
aTachometer
bCombination meter
eTurn signal indicator light
hOil level switch
iHorn
kRear turn signal light (right)
lRear turn signal light (left)
mFront turn signal light (right)
nFront turn signal light (left)
oTail/brake light
pRear brake light switch
vTurn signal switch
wHorn switch
xTurn signal relay
yFuel pump (thermistor)
|Front brake light switch
 Signaling system fuse

8 - 22
–+ELECSIGNALING SYSTEM
TROUBLE SHOOTING
• Any of the following fail to light: turn signal light, brake light or an indicator light.
• The horn fails to sound.
Check the main and signal system fuses
continuity.
Check the condition of the battery.
Check the main switch.
Check the entire signaling system’s wiring.
Check the bulbs and
bulb sockets.
Check the LED’s of
the indicator light.
Check the brake
switchs.
Replace the meter
assembly.
Check the neutral
switch.
Replace the meter
assembly. Check the relay unit.
Check the continuity of the thermistor in the fuel pump.OK
OK
OK
OK
OK
OK
OK
OK
OK
OKNo good
No good
No good
No goodReplace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.Recharge or replace.
Recharge or replace.
No goodNo good
No good
No good
No good
No good
No good
No good No good
No good OK
OK
BAD
OK Check the horn switch.
Check the horn. Replace.
Replace. Check the turn signal
switch.
Replace the turn
signal relay.
Replace the meter
assembly.
Replace the meter
assembly.
Replace the meter
assembly.Check the oil level
switch.
Replace the fuel
pump. Replace the left
handlebar switch.
Replace the
left handlebar
switch.