Page 41 of 381
ENGINE SPECIFICATIONS
SPEC
2 - 3
Oil filter
Oil filter type Cartridge (paper) ----
Bypass valve opening pressure 180 ~ 220 kPa
(1.8 ~ 2.2 kgf/cm
2
, 25.6 ~ 31.3 psi)----
Oil pump
Oil pump type Trochoidal ----
Inner rotor-to-outer rotor tip clear-
ance0.09 ~ 0.15 mm (0.004 ~ 0.006 in) ----
Outer rotor-to-oil pump housing
clearance0.03 ~ 0.08 mm (0.001 ~ 0.003 in) ----
Cooling system
Radiator capacity 2.75 L (2.42 Imp qt, 2.91 US qt)
Radiator cap opening pressure 95 ~ 125 kPa
(0.95 ~ 1.25 kgf/cm
2
, 13.1 ~ 17.8 psi)----
Upper radiator core
Width 414 mm (16.3 in) ----
Height 248 mm (9.76 in) ----
Depth 24 mm (0.94 in) ----
Lower radiator core
Width 211 mm (8.31 in) ----
Height 158 mm (6.22 in) ----
Depth 24 mm (0.94 in) ----
Coolant reservoir
Capacity 0.6 L (0.53 Imp qt, 0.63 US qt) ----
Water pump
Water pump type Single-suction centrifugal pump ----
Reduction ratio 88/47
´
28/25 (2.097) ----
Maximum impeller shaft tilt ---- 0.15 mm
(0.006 in)
Starting system type
Electric starter
Spark plugs
Model (manufacturer)
´
quantity R0256R-10 (NGK)
´
4 ----
Spark plug gap 0.7 ~ 0.8 mm (0.028 ~ 0.031 in) ----
Cylinder head
Maximum warpage ---- 0.06 mm
(0.0024 in) Item Standard Limit
Page 47 of 381
ENGINE SPECIFICATIONS
SPEC
2 - 9
Oil ring
Dimensions (B
´
T) 1.5
´
2.5 mm (0.059
´
0.098 in) ----
End gap (installed) 0.1 ~ 0.3 mm (0.004 ~ 0.012 in) ----
Connecting rods
Crankshaft pin-to-big end bearing
clearance0.058 ~ 0.078 mm (0.0023 ~ 0.0031 in) ----
Bearing color code 2 = Blue, 3·4 = Black, 5·6 = Brown,
7·8 = Green, 9 = Yellow----
Crankshaft
Width A 54.4 ~ 56.0 mm (2.142 ~ 2.205 in) ----
Width B 292.8 ~ 294.0 mm (11.53 ~ 11.57 in) ----
Maximum runout C 0.035 mm
(0.0014 in)
Big end side clearance D 0.16 ~ 0.26 mm (0.006 ~ 0.010 in) ----
Crankshaft journal-to-crankshaft
journal bearing clearance0.036 ~ 0.056 mm (0.0014 ~ 0.0022 in) ----
Bearing color code1·2 = Blue, 3·4 = Black, 5·6 = Brown, 7·8 =
Green, 9·10 = Yellow, 11 = Violet----
Clutch
Clutch type Wet, multiple disc ----
Clutch release method Hydraulic inner push ----
Operation Left-hand operation ----
Recommended fluid Brake fluid DOT4 ----
Friction plates #1
Thickness 2.9 ~ 3.1 mm (0.114 ~ 0.122 in) 2.8 mm
(0.110 in)
Plate quantity 8 ----
Friction plate #2
Thickness 3.7 ~ 3.9 mm (0.146 ~ 0.154 in) 3.6 mm
(0.142 in)
Plate quantity 1 ----Item Standard Limit
B
T
D
FCCC
A
B
E
Page 51 of 381
CHASSIS SPECIFICATIONSSPEC
2 - 13
Front suspension
Suspension type Telescopic fork ----
Front fork type Coil spring/oil damper ----
Front fork travel 120 mm (4.72 in) ----
Spring
Free length 240 mm (9.45 in) ----
Spacer length 127 mm (5.00 in) ----
Installed length 226 mm (8.90 in) ----
Spring rate (K1) 9.3 N/mm (0.95 kgf/mm, 53.2 lb/in)
Spring stroke (K1) 0 ~ 120 mm (0 ~ 4.72 in) ----
Optional spring available No ----
Fork oil
Recommended oil Suspension oil “01” or equivalent ----
Quantity (each front fork leg) 460 cm
3 (16.2 Imp oz, 15.6 US oz) ----
Level (from the top of the outer
tube, with the outer tube fully
down, and without the fork
spring)170 mm (6.69 in) ----
Damper adjusting rod locknut dis-
tance31 mm (1.22 in) ----
Spring preload adjusting positions
Minimum 0 [0 mm ( 0 in)] ----
Standard 14 [14 mm (0.55 in)] ----
Maximum 18-1/2 [18.5 mm (0.73 in)] ----
Rebound damping adjusting posi-
tions
Minimum* 17 ----
Standard* 6 ----
Maximum* 1 ----
Compression damping adjusting
positions
Minimum* 20 ----
Standard* 6 ----
Maximum* 1 ----
* from the fully turned-in positionItem Standard Limit
Page 52 of 381
CHASSIS SPECIFICATIONSSPEC
2 - 14
Steering
Steering bearing type Angular ball bearings ----
Rear suspension
Suspension type Swingarm (link suspension) ----
Rear shock absorber assembly
typeCoil spring/gas-oil damper ----
Rear shock absorber assembly
travel63 mm (2.48 in) ----
Spring
Free length 160 mm (6.30 in) ----
Installed length 146 mm (5.75 in) ----
Spring rate (K1) 95 N/mm (9.69 kgf/mm, 543 lb/in) ----
Spring stroke (K1) 0 ~ 63 mm (0 ~ 2.48 in) ----
Optional spring available No ----
Standard spring preload gas/air
pressure 1,200 kPa (12 kgf/cm
2, 171 psi) ----
Spring preload adjusting positions
Minimum 0 [11 mm (0.43 in)] ----
Standard 6 [14 mm (0.55 in)] ----
Maximum 20 [21 mm (0.84 in)] ----
Rebound damping adjusting posi-
tions
Minimum* 50 ----
Standard* 10 ----
Maximum* 0 ----
Compression damping adjusting
positions
Minimum* 25 ----
Standard* 10 ----
Maximum* 0 ----
* from the fully turned-in position
Swingarm
Free play (at the end of the swing-
arm)
Radial ---- 1 mm
(0.04 in)
Axial ---- 1 mm
(0.04 in)
Drive chain
Model (manufacturer) 50ZVM (DAIDO) ----
Link quantity 118 ----
Drive chain slack 40 ~ 50 mm (1.57 ~ 1.97 in) ----
Maximum ten-link section 150.1 mm (5.91 in) ----Item Standard Limit
Page 53 of 381
ELECTRICAL SPECIFICATIONSSPEC
2 - 15
ELECTRICAL SPECIFICATIONS
Item Standard Limit
System voltage12 V ----
Ignition system
Ignition system type C.D.I. ----
Ignition timing 5˚ BTDC at 1,100 r/min ----
Advanced timing 55˚ BTDC at 5,000 r/min ----
Advancer type Throttle position sensor and electrical ----
Pickup coil resistance/color 421 ~ 569 W / Gy–B ----
C.D.I. unit model (manufacturer) F8T19371 (MITSUBISHI) ----
Ignition coils
Model (manufacturer) F6T549 (MITSUBISHI) ----
Minimum ignition spark gap 6 mm (0.24 in) ----
Primary coil resistance 0.16 ~ 0.21 W ----
Secondary coil resistance 5.0 ~ 6.8 kW ----
Throttle position sensor standard
resistance4 ~ 6 kW----
Charging system
System type AC magneto ----
Model (manufacturer) F4T254 (MITSUBISHI) ----
Nominal output 14 V / 22.5 A at 5,000 r/min ----
Stator coil resistance 0.38 ~ 0.46 W at 20˚C (68˚F) ----
Rectifier/regulator
Regulator type Semiconductor-short circuit ----
Model SH650D-11 (SHINDENGEN) ----
No-load regulated voltage 14.1 ~ 14.9 V ----
Capacity 18 A ----
Withstand voltage 200 V ----
Battery
Battery type GT9B-4 ----
Battery voltage/capacity 12V / 8AH ----
Headlight typeHalogen bulb
Indicator light type ´ quantityLED ´ 5
Bulbs (voltage/wattage ´ quantity)
Headlight R. 12 V 60 W ´ 1 / L. 12 V 51 W ´ 1 ----
Auxiliary light 12 V 5 W ´ 2 ----
Tail/brake light 12 V 5 W / 21 W ´ 1 ----
Front turn signal light 12 V 21 W ´ 2 ----
Rear turn signal light 12 V 21 W ´ 2 ----
Meter light 12 V 1.4 W ´ 2 ----
Page 54 of 381
ELECTRICAL SPECIFICATIONSSPEC
2 - 16
Electric starting system
System type Constant mesh ----
Starter motor
Model (manufacturer) SM-14 (MITSUBA) ----
Power output 0.6 kW ----
Armature coil resistance 0.0015 ~ 0.0025 W----
Brushes
Overall length 10 mm (0.40 in) 3.5 mm
(0.14 in)
Spring force 7.16 ~ 9.52 N
(730 ~ 971 gf, 25.8 ~ 34.3 oz)----
Commutator resistance 0.025 ~ 0.035 W----
Commutator diameter 28 mm (1.10 in) 27 mm
(1.06 in)
Mica undercut 0.7 mm (0.03 in) ----
Starter relay
Model (manufacturer) MS5F-631 (JIDECO) ----
Amperage 180 A ----
Coil resistance 4.18 ~ 4.62 W ----
Horn
Horn type Plain ----
Model (manufacturer) ´ quantity YF-12 (NIKKO) ´ 1 ----
Max. amperage 3 A ----
Turn signal relay
Relay type Full-transistor ----
Model (manufacturer) FE246BH (DENSO) ----
Self-cancelling device built-in No ----
Turn signal blinking frequency 75 ~ 95 cycles/min. ----
Wattage 21 W ´ 2 + 3.4 W ----
Oil level switch model (manufac-
turer)071380-0480 (DENSO) ----
Fuel pump relay model (manufac-
turer)G8R-30Y-J (OMRON) ----
Thermo switch model (manufac-
turer)5EB (NIPPON THERMOSTAT) ----
Fuses (amperage ´ quantity)
Main fuse 30 A ´ 1 ----
Headlight fuse 20 A ´ 1 ----
Signaling system fuse 20 A ´ 1 ----
EFI fuse 20 A ´ 1 ----
ECU fuse 7.5 A ´ 1 ----
Radiator fan fuse 7.5 A ´ 1 ----
Backup fuse (odometer) 7.5 A ´ 1 ---- Item Standard Limit
Page 56 of 381
2 - 18
SPEC
ENGINE TIGHTENING TORQUES
Item Fastener Thread size Q’tyTightening torque
Remarks
Nm m·kgf ft·lb
Spark plugs – M10 4 13 1.3 9.4
Cylinder head Nut M10 8 50 5.0 36
E
Cylinder head Cap nut M10 2 50 5.0 36E
Cylinder head Bolt M6 2 12 1.2 8.7
Camshaft caps Bolt M6 28 10 1.0 7.2
E
Cylinder head cover Bolt M6 6 12 1.2 8.7
Oil passage check bolt Bolt M8 1 20 2.0 14
Cap bolt (timing chain tensioner) Bolt M6 1 10 1.0 7.2
Camshaft sprocket Bolt M7 4 24 2.4 17
Generator rotor Bolt M10 1 65 6.5 47
E
Pickup coil rotor Bolt M10 1 45 4.5 32E
Water pump inlet pipe Bolt M6 1 10 1.0 7.2LT
Water pump outlet pipe Bolt M6 1 10 1.0 7.2LT
Oil/water pump assembly
driven sprocketBolt M6 1 15 1.5 11LT
Oil pump Bolt M6 1 12 1.2 8.7
Oil cooler Bolt M20 1 63 6.3 45
E
Engine oil drain bolt – M14 1 43 4.3 31
Oil strainer housing Bolt M6 2 10 1.0 7.2
LT
Oil/water pump assembly
driven sprocket coverBolt M6 1 12 1.2 8.7LT
Oil delivery pipe Bolt M6 1 10 1.0 7.2LT
Oil filter bolt Bolt M20 1 70 7.0 50
Oil filter cartridge – M20 1 17 1.7 12
E
Exhaust pipe joints Bolt M8 8 20 2.0 14
Exhaust pipe Bolt M8 1 20 2.0 14
Exhaust pipe bracket Bolt M8 1 24 2.4 17
Exhaust pipe emission check
boltsBolt M6 4 10 1.0 7.2
Muffler clamp Bolt M8 1 20 2.0 14
Muffler Bolt M10 1 38 3.8 27
Muffler bracket Bolt M8 2 28 2.8 20
Crankcase (cylinder head) Stud bolt M10 10 10 1.0 7.2
E
Crankcase Bolt M9 10 32 3.2 23E
Crankcase Bolt M6 2 14 1.4 10E
Crankcase Bolt M6 14 12 1.2 8.7E
Crankcase Bolt M8 2 24 2.4 17E
Generator rotor cover Bolt M6 9 12 1.2 8.7
Clutch cover Bolt M6 9 12 1.2 8.7
Pickup coil rotor cover Bolt M6 7 12 1.2 8.7
TIGHTENING TORQUES
Page 57 of 381
2 - 19
SPEC
Shift shaft cover Bolt M6 6 12 1.2 8.7
Oil baffle plate Bolt M6 5 10 1.0 7.2
LT
Timing mark accessing screw – M8 1 15 1.5 11
Starter clutch Bolt M6 3 12 1.2 8.7
LT
Clutch boss Nut M20 1 70 7.0 50Use a lock
washer.
Clutch spring Bolt M6 6 8 0.8 5.8
Drive sprocket Nut M18 1 70 7.0 50Use a lock
washer.
Main axle bearing housing Screw M6 3 12 1.2 8.7
LT
Shift drum retainer Bolt M6 2 10 1.0 7.2LT
Shift shaft spring stopper Bolt M8 1 22 2.2 16LT
Shift rod locknut Nut M6 2 7 0.7 5.1
Shift arm Bolt M6 1 10 1.0 7.2
Stator coil Bolt M6 3 10 1.0 7.2
LT
Neutral switch – M10 1 20 2.0 14
Pickup coil Screw M5 2 4 0.4 2.9
LT
Thermo switch – M16 1 23 2.3 17
Camshaft sensor Bolt M6 1 10 1.0 7.2
LT
Speed sensor Bolt M6 1 10 1.0 7.2LT
Coolant temperature sensor – M12 1 18 1.8 13
Intake air temperature sensor – M12 1 18 1.8 13
Intake air pressure sensor Screw M5 2 5 0.5 3.6
LT
Atmospheric pressure sensor Screw M5 2 5 0.5 3.6LT
Air funnel Bolt M6 8 10 1.0 7.2LT
Throttle body assembly Bolt M6 16 10 1.0 7.2
Injector 2 cover Bolt M5 8 8 0.8 5.8
LT
Fuel distributor Bolt M6 6 10 1.0 7.2LT
Injector fuel pipe 1,3 and 4 Union bolt M12 3 30 3.0 22
Injector fuel pipe 2 – M12 1 30 3.0 22
Fuel hose joint pipe Bolt M5 1 6 0.6 4.3
LT
Pressure sensor bracket Bolt M5 2 8 0.8 5.8LT
Item Fastener Thread size Q’tyTightening torque
Remarks
Nm m·kgf ft·lb
TIGHTENING TORQUES