1999 YAMAHA YZF-R7 oil

7 - 10
CHAS
REAR WHEEL, BRAKE DISC, AND REAR WHEEL
SPROCKET
EB701010
Order Job/Part Q’ty Remarks
Removing the brake disc and rear
wheel sprocketRemove the parts in the order listed.
1 Brake disc 1
2 Rear wheel sprocket 1
3 Oil seal cover (left and right) 2
4 Spacer (left and right) 2
5 Oil seal 1
6 Bearing 1
7 Rear wheel drive hub 1
8 Rear wheel drive hub damper 6
9 Rear wheel 1
For installation, reverse the removal
procedure.

7 - 11
CHAS
REAR WHEEL, BRAKE DISC, AND REAR WHEEL
SPROCKET
Order Job/Part Q’ty Remarks
Disassembling the rear wheelRemove the parts in the order listed.
1 Spacer 1
2 Bearing 1
3 Spacer 1
4 Oil seal 1
5 Circlip 1
6 Bearing 1
For assembly, reverse the disassembly
procedure.

7 - 12
CHAS
REAR WHEEL, BRAKE DISC, AND REAR WHEEL
SPROCKET
EB701100
REMOVING THE REAR WHEEL
1. Stand the motorcycle on a level surface.
WARNINGWARNING
Securely support the motorcycle so that
there is no danger of it falling over.
NOTE:
Place the motorcycle on a suitable stand
so that the rear wheel is elevated.
2. Remove:
• brake caliper
NOTE:
Do not depress the brake pedal when
removing the brake caliper.
3. Remove:
• wheel axle nut
• washer
• wheel axle
• rear wheel
NOTE:
Push the rear wheel forward and
remove the drive chain from the rear
wheel sprocket.
EB701400
CHECKING THE REAR WHEEL
1. Check:
• wheel axle
• rear wheel
• wheel bearings
• oil seals
• brake disc
Refer to “FRONT WHEEL”.
2. Check:
• tire
• rear wheel
Damage/wear ® Replace.
Refer to “CHECKING THE TIRES” and
“CHECKING THE WHEELS” in chapter 3.

7 - 14
CHAS
REAR WHEEL, BRAKE DISC, AND REAR WHEEL
SPROCKET
EB701710
INSTALLING THE REAR WHEEL
1. Lubricate:
• wheel axle
• wheel bearings
• oil seal lips
Recommended lubricant
Lithium soap base grease
2. Adjust:
• drive chain slack a
Refer to “ADJUSTING THE DRIVE
CHAIN SLACK” in chapter 3.
Drive chain slack
40 ~ 50 mm (1.57 ~ 1.97 in)
3. Tighten:
• wheel axle
• wheel axle nut
• brake caliper bolts
WARNINGWARNING
Make sure that the brake hose is routed
properly.
EB701900
ADJUSTING THE REAR WHEEL STATIC
BALANCE
NOTE:
• After replacing the tire, wheel or both,
the rear wheel static balance should be
adjusted.
• Adjust the rear wheel static balance
with the brake disc and rear wheel
drive hub installed.
1. Adjust:
• rear wheel static balance
Refer to “FRONT WHEEL”.
T R..150 Nm (15.0 m · kg, 110 ft · lb)
T R..45 Nm (4.5 m · kg, 32 ft · lb)
T R..40 Nm (4.0 m · kg, 29 ft · lb)

7 - 30
CHAS
4. Fill:
• brake fluid reservoir
(with the specified amount of the rec-
ommended brake fluid)
WARNINGWARNING
• Use only the designated brake fluid.
Other brake fluids may cause the rub-
ber seals to deteriorate, causing leak-
age and poor brake performance.
• Refill with the same type of brake fluid
that is already in the system. Mixing
brake fluids may result in a harmful
chemical reaction, leading to poor
brake performance.
• When refilling, be careful that water
does not enter the brake fluid reser-
voir. Water will significantly lower the
boiling point of the brake fluid and
could cause vapor lock.
ACHTUNG:CAUTION:
Brake fluid may damage painted sur-
faces and plastic parts. Therefore,
always clean up any spilt brake fluid
immediately.
5. Bleed:
• brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
Recommended brake fluid
DOT 4
6. Check:
• brake fluid level
Below the minimum level mark a ®
Add the recommended brake fluid to
the proper level.
Refer to “CHECKING THE BRAKE
FLUID LEVEL” in chapter 3.
7. Check:
• brake lever operation
Soft or spongy feeling ® Bleed the
brake system.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
FRONT AND REAR BRAKES

7 - 32
CHAS

4. Fill:
• brake fluid reservoir
(with the specified amount of the rec-
ommended brake fluid)
WARNINGWARNING

• Use only the designated brake fluid.
Other brake fluids may cause the rub-
ber seals to deteriorate, causing leak-
age and poor brake performance.
• Refill with the same type of brake fluid
that is already in the system. Mixing
brake fluids may result in a harmful
chemical reaction, leading to poor
brake performance.
• When refilling, be careful that water
does not enter the brake fluid reser-
voir. Water will significantly lower the
boiling point of the brake fluid and
could cause vapor lock.
ACHTUNG:CAUTION:

Brake fluid may damage painted sur-
faces and plastic parts. Therefore,
always clean up any spilt brake fluid
immediately.
5. Bleed:
• brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
Recommended brake fluid
DOT 4
6. Check:
• brake fluid level
Below the minimum level mark
a

®
Add the recommended brake fluid to
the proper level.
Refer to “CHECKING THE BRAKE
FLUID LEVEL” in chapter 3.
7. Check:
• brake pedal operation
Soft or spongy feeling
®
Bleed the
brake system.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
FRONT AND REAR BRAKES

7 - 36
CHAS

FRONT AND REAR BRAKES
EB702202
Order Job/Part Q’ty Remarks
Removing the rear brake master cyl-
inder and brake fluid reservoir
Remove the parts in the order listed.
Brake fluid Drain.
1 Brake fluid reservoir cap 1
2 Brake fluid reservoir diaphragm holder 1
3 Brake fluid reservoir diaphragm 1
4 Brake fluid reservoir 1
5 Plastic clamp 1
6 Plastic locking tie 1
7 Brake fluid reservoir hose 1
8 Hose joint 1
9 Oil seal 1
10 Union bolt 1
11 Copper washer 2
12 Brake hose 1
13 Brake master cylinder 1
For installation, reverse the removal
procedure.

7 - 40
CHASFRONT AND REAR BRAKES
1. Install:
• brake master cylinder 1
NOTE:
• Install the brake master cylinder holder
with the “UP” mark facing up.
• Align the end of the brake master cyl-
inder holder with the punch mark a in
the right handlebar.
• First, tighten the upper bolt, then the
lower bolt.
1a
T R..13 Nm (1.3 m · kg, 9.4 ft · lb)
2. Install:
• copper washers
• brake hose
• union bolt
WARNINGWARNING
Proper brake hose routing is essential to
insure safe motorcycle operation. Refer
to “CABLE ROUTING”.
NOTE:
• While holding the brake hose, tighten
the union bolt as shown.
• Turn the handlebars to the left and to
the right to make sure that the brake
hose does not touch other parts (e.g.,
wire harness, cables, leads). Correct if
necessary.
New
T R..30 Nm (3.0 m · kg, 22 ft · lb)
3. Fill:
• brake fluid reservoir
(with the specified amount of the rec-
ommended brake fluid)
WARNINGWARNING
• Use only the designated brake fluid.
Other brake fluids may cause the rub-
ber seals to deteriorate, causing leak-
age and poor brake performance.
• Refill with the same type of brake fluid
that is already in the system. Mixing
brake fluids may result in a harmful
chemical reaction, leading to poor
brake performance.
• When refilling, be careful that water
does not enter the brake fluid reser-
voir. Water will significantly lower the
boiling point of the brake fluid and
could cause vapor lock.
Recommended brake fluid
DOT 4