1999 YAMAHA YZF-R7 oil

7 - 84
CHAS
4. Check:
• dust covers
• spacer
• oil seals
Damage/wear ® Replace.
• bearings
Damage/pitting ® Replace.
EB707410
CHECKING THE DRIVE CHAIN
1. Measure:
• ten-link section a of the drive chain
Out of specification ® Replace the
drive chain.
NOTE:
• While measuring the ten-link section,
push down on the drive chain to
increase its tension.
• Measure the length between drive
chain roller 1 and A as shown.
• Perform this measurement at two or
three different places.
Max. ten-link drive chain sec-
tion
150.1 mm (5.91 in)
2. Check:
• drive chain
Stiffness ® Clean and lubricate or
replace.
3. Clean:
• drive chain
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Wipe the drive chain with a clean
cloth.
b. Put the drive chain in kerosine and
remove any remaining dirt.
SWINGARM AND DRIVE CHAIN

7 - 85
CHAS
c. Remove the drive chain from the ker-
osine and completely dry it.
ACHTUNG:CAUTION:
This motorcycle has a drive chain with
small rubber O-rings 1 between the
drive chain side plates. Never use high-
pressure water or air, steam, gasoline,
certain solvents (e.g., benzine), or a
coarse brush to clean the drive chain.
High-pressure methods could force dirt
or water into the drive chain’s internals,
and solvents will deteriorate the O-
rings. A coarse brush can also damage
the O-rings. Therefore, use only kero-
sine to clean the drive chain.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
4. Check:
• O-rings 1
Damage ® Replace the drive chain.
• drive chain rollers 2
Damage/wear ® Replace the drive
chain.
• drive chain side plates 3
Cracks/damage/wear ® Replace the
drive chain.
5. Lubricate:
• drive chain
Recommended lubricant
Engine oil or chain lubricant
suitable for O-ring chains
6. Check:
• drive sprocket
• rear wheel sprocket
More than 1/4 tooth a wear ® Replace
the drive chain sprockets as a set.
Bent teeth ® Replace the drive chain
sprockets as a set.
b Correct
1Drive chain roller
2Drive chain sprocket
SWINGARM AND DRIVE CHAIN

8 - 1
–+ELEC

ELECTRICAL COMPONENTS
EB800000
ELECTRICAL
ELECTRICAL COMPONENTS
1
Wire harness
2
Main switch
3
Front brake light switch
4
Ignition coils
5
Clutch switch
6
Throttle position sensor
7
Intake air temperature sensor
8
Intake air pressure sensor
9
Atmospheric pressure sensor
0
Turn signal relay
A
Relay unit
B
ECU
C
CDI unit
D
Fuse box
E
Fall detection switch
F
Starter relay
G
Main fuse
H
Main relay
I
Battery
J
Rectifier/regulator
K
Rear brake light switch
L
Neutral switch
M
Speed sensor
N
Sidestand switch
O
Stator coil assembly
P
Oil level switch
Q
Pickup coil
R
Radiator fan
S
Horn
T
Coolant temperature
sender
U
Thermo switch
V
Camshaft sensor
8

8 - 3
–+ELEC

CHECKING THE SWITCHES
EB801010
CHECKING THE SWITCHES
Check each switch for damage or wear, proper connections, and also for continuity between
the terminals. Refer to “CHECKING SWITCH CONTINUITY”.
Damage/wear
® Repair or replace the switch.
Improperly connected ® Properly connect.
Incorrect continuity reading ® Replace the switch.
1Main switch
2Light switch
3Pass switch
4Dimmer switch
5Turn signal switch6Horn switch
7Clutch switch
8Engine stop switch
9Start switch
0Front brake light switchAOil level switch
BRear brake light switch
CFuse
DNeutral switch
ESidestand switch
1L/YL/B
LL/R
R
Br/L
OFF
ONP
L/RLBr/LRL/YL/B
3
4
5
Br/WR/YPLB
Dg Y
G Ch
B/YL/YPASS—
R/YY
67
YG
—BP
(BLUE)
(BLACK)
(BLACK)
R/WBr
R/BB
G/YL/W
B
B
G/YBr
OFF
ChBr/WDg
8R/WR/B
9
0—L/WB
2R/YL•
C
E
(BLUE)
B
B
B D
(BROWN)
Sb
A
W
L/YB/Y
L/YB/Y

8 - 5
–+ELECCHECKING THE BULBS AND BULB SOCKETS
WARNINGWARNING
Since the headlight bulb gets extremely
hot, keep flammable products and your
hands away from the bulb until it has
cooled down.
CAUTION:
• Be sure to hold the socket firmly when
removing the bulb. Never pull the lead,
otherwise it may be pulled out of the ter-
minal in the coupler.
• Avoid touching the glass part of the head-
light bulb to keep it free from oil, other-
wise the transparency of the glass, the
life of the bulb and the luminous flux will
be adversely affected. If the headlight
bulb gets soiled, thoroughly clean it with
a cloth moistened with alcohol or lacquer
thinner.
2.Check:
• bulb (for continuity)
(with the pocket tester)
No continuity ® Replace.
NOTE:
Before checking for continuity, set the
pocket tester to “0” and to the “W ´ 1”
range.
t t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Connect the tester positive probe to ter-
minal 1 and the tester negative probe to
terminal 2, and check the continuity.
b. Connect the tester positive probe to ter-
minal 1 and the tester negative probe to
terminal 3, and check the continuity.
c. If either of the readings indicate no conti-
nuity, replace the bulb.
s s s s s s s s s s s s s s s s s s s s s s s s s s s s
Pocket tester
90890-03112

8 - 7
–+ELECIGNITION SYSTEM
EB802001
IGNITION SYSTEM
CIRCUIT DIAGRAM
B
(BLACK) (DARK GRAY)
(BLACK)B
L
B
L
K
WWW
86
7RR
Br
BBRR
L/W BrL/W
RR
R
B
B
BBB
B
R
WWW(BLACK)
L/W
B
R/B
R/L
G/B
R/L
L/W
B (BLUE)
Gy
Gy/B
B
B(BLUE)
Gy
B
Br
G
L/R
B
Br
G L/R
B
Br/W
Br
B
B
B
B
L/WBr
R/W
G/Y R/W
B/WB/L(GRAY)
(BROWN)
h
Br
YB
BBr
Y (BROWN) (BROWN)
R/YLBr/WP
B(BLUE) (BLUE)(BLACK) (BLACK)
Br
BBR/WR/B
Y
P
ON OFF
R
RL/R
LBr/L
B
R/L
G/W(BLACK)
R/L R/BR/G L/R(GREEN)
(BLACK) (BLACK)(BLACK)(BLACK)
O Gy
B
Br/G
B Br
L/G W/G
Y/G
BYL
B
B
G
Ch Dg
BL/W
L/R
R/BB/Y
L/YSb
R/L R/B
Br/WB1G/W B/L
L/Y
W
B/L
W/B L/YB/L
W/YL/Y
L/Y
Br L
R
Br/LR
Br/L
L/W
L/Y
Br
L/W
L/Y L/B
L L/R
B L/Y
L/R LB B BB
W
WW
W
WW
B
BB
B
B B1
B
BB
B
B
B/YL/Y
B/YL/Y
R/Y
L P
B Br/WDg
ChB/YYG
L/Y
Ch
B/YDg
G
L/YY
B
R
G
B/L
YLWBYPBL
GBB/W
(BLACK)YB
BCh
(BLACK)BDg
B
(GRAY)(BLACK)
(BLACK)
(BLACK) (GRAY)
(GRAY)
(GRAY)
(GRAY) (GRAY)B/W B/L
B/L B/L
W/LP/B Y/L
R
B
PASS
(BLACK)
(BLACK)ChB
(BLACK)DgB
N
B(BLACK)B
(BLACK) (BLACK)
O/G B(BLACK) (BLACK)
L
R/L G/B
M
R/L L/B
N
R/LR/L O/B
OY
Y/R C YG/R C GBr/R C BrGy/R C Gy
R R/LRRRRY
P
RG G(BROWN)
Q
RBr Br
Gy(DARK GRAY)R(GRAY)
R
R/YLg/Y
R/Y Lg/Y R/WB/L
R/Y
R
Y/L
B
L/R
YL/R
Gy/B
Gy
G/WB1
W/Y
W1
L/R B/L
YLW/B
Y/L W/L
P/W P/LR/Y
Br/W R/W
Lg/YL/W B/W
R/L
R/B L/WW G
Lg
L/R L/BSb
B/Y B B/R L/Y
RBR
R/G
4
BL/Y
BB
Br/L
BrBrL
B
B
B
B
BR/GB1
B
Y
B
R/WR/B
R/GR/BL/RR/L
Br
G/WR/L
L/YW/BB/L
GyGy/B
R/L
L/R
L/W
B/LL
B
Br/W
Br
Y
LPWP
B2
B2
R PB
(BLACK)
B3
B3W2
Y/G L/GBr/G Br/R
Gy/R
BrBrO/B
G/Y L/B G/B G/R
Y/R
W/G Y/B R/B
O/B
R/L
L/B
GyO
O Lg/R
B
B
B
BB Gy
Gy/G Gy/G Gy/G
O/G O/GO/G
Gy GyGy/G
Br/G
W/G
Y/G
L/G
Br
WW/YB/L
L/Y
Lg/RG/Y W/YL/R
Y/B
L/YBSb
Sb
R/GG/WWYChL
W
BrP
P G Y Ch Dg B
Dg
B
BBBB
B
Dg
ChBr
LR/Y
L/Y B/Y
Br/LBr/LBr/L
BrR/YR/W
B2
Gy/BB3
R/B
G/B
L/B
O/B
Gy/R
Lg/RY/R
G/R
Br/R
R/W
R/Y
Lg/Y
W1
W2
(BLACK)
(BLACK)
(BLACK)
(BLACK) (GRAY)
B
L
B
B/L
Br/W
B/LG/W
S
T
U
V W J
Z
R/G
B L/Y
W/YG/Y W Y/B
Br
G/WLg/R Lg Y
ChDg
L
gf f e dc b a` ] \[ FE DC
I
G
H
X
j k
l
m
n
op
i w v u

t s
r qBA@Br9 5 3 2
1
Œ

 
£¢ ¤
¥
¦xy

(BLACK)
Y
L/W
Y/B
G/Y
Y/L
W/L
P/BR
B3 W/B
B/L
L
Y
P/W
P/L
Br
G/W
B/W
W/Y
Br
B2
|
~
z } {
L/Y
A
A
A
A
AA
AAAA
A C
A
A
A
A A
A
P/LP/W
BB/L BB/L
DL DL
C
W/LP/B
WIRE HARNESS SUB LEAD
B/L B/L
BB
R/L R/L L
R/L R/L L
LRR
LR
R(GRAY)
(GRAY)
WIRE HARNESS SUB LEADY/R
Br/RP/W
G/R Gy/R P/L
WYBr
PG
Gy(BLACK)
(BLACK)
WIRE HARNESS SUB LEAD HEADLIGHT AND METER SUB-WIRE HARNESS
(BLACK)
(BLACK)
WIRE HARNESS
Y W/Y G/WG/W
R/G L G/Y Dg
Br
GY
G L/YW/Y
L/Y BBr
B W Y/B Lg Lg/RCh L/R
L/R
G/Y
R/GDg
L
Lg/R
Lg
W
Y/B ChA
BC
D
D R/L D R/L D R/L D
R
B1
Br/G
W/G
Y/G
L/G
Br
Gy
TCylinder #2-ignition coil
UCylinder #3-ignition coil
VCylinder #4-ignition coil
WCDI unit
ZNeutral switch
}Engine stop switch
£ECU fuse
1Main switch
5Battery
6Main switch
0Relay unit
ADiode
BSidestand switch
JECU
SCylinder #1-ignition coil

8 - 8
–+ELECIGNITION SYSTEM
TROUBLESHOOTING
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
No good
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK The ignition system fails to operate (no spark or intermittent spark).
Check the main and ECU fuses for
continuity.Replace.
Check the condition of the bat-
tery.Recharge or replace.
Check the spark plug. Re-gap or replace.
Measure the ignition spark gap. Ignition system is OK.
Measure the ignition coil resis-
tance.Replace.
Measure the pickup coil resis-
tance.Replace.
Check the main switch. Replace.
Check the engine stop switch.Replace the right handlebar
switch.
Check the neutral switch. Replace.
Check the diode. Replace.
Check the sidestand switch. Replace.
Check the relay unit. Replace.
Check the entire ignition sys-
tem’s wiring.Repair or replace.
Replace the CDI unit.
No good
No good
No good
No good
No good
No good
No good
No good
No good
OK
No good
No good
No good

8 - 9
–+ELECIGNITION SYSTEM
BAD
NOTE:
• Before troubleshooting, remove the following part(-s):
1) fuel tank
2) air filter case
3) bottom cowling
4) front cowling
5) rear cowling
• Troubleshoot with the following special tool(-s).
Replace the ECU.
Ignition checker
90890-06754
Pocket tester
90890-03112
MEASURING THE IGNITION SPARK GAP
The following procedure applies to all of
the spark plugs.
• Disconnect the ignition coil from the spark
plug.
• Connect the ignition checker 1 as shown.
2 Ignition coil
• Set the main switch to “ON”.
• Measure the ignition spark gap a.
• Crank the engine by pushing the start
switch and gradually increase the spark
gap until a misfire occurs.
• Is there a spark and is the spark gap
within specification?
Yes ® Good.
No ® Measure the ignition coil resistance.
Minimum ignition spark gap
6 mm (0.24 in)