1999 TOYOTA CAMRY brake

PP0IA±01
± PREPARATIONBRAKE
PP±89
141 Author: Date:
LUBRICANT
ItemCapacityClassification
Brake fluid±SAE J1703 or FMVSS No.116 DOT3

PP0L0±01
± PREPARATIONBODY ELECTRICAL
PP±103
155 Author: Date:
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
SyphonBrake fluid level warning switch
Bulb (3.4 W)Fuel sender gauge, Seat belt warning relay
Bulb (21 W)Turn signal flasher relay
Dry cell batteryFuel sender gauge
Torque wrench
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

SS04X±01
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS±61
224 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT:
Hub nut1031,05076
Tie rod end lock nut7475054
Steering knuckle x Shock absorber2112,150156
Steering knuckle x Brake caliper1071,09079
Steering knuckle x Tie rod end4950036
Axle hub x Drive shaft2943,000217
Lower ball joint x Lower suspension arm1271,30094
Lower ball joint x Steering knuckle1231,25090
Steering knuckle x Disc brake dust cover8.38574 in.´lbf
Drive shaft center bearing lock bolt3233024
Suspension support x Body8082059
Suspension support x Piston rod4950036
ABS speed sensor set bolt8.08271 in.´lbf
Flexible hose and ABS speed sensor wire harness x Shock absorber2930022
Lower suspension arm set bolt2062,100152
Stabilizer bar bracket x Suspension member1919514
Stabilizer bar link set bolt3940029
REAR:
Hub nut1031,05076
No.2 lower suspension arm lock nut5657041
Brake caliper x Rear axle carrier4747534
Axle hub bearing set bolt8082059
Shock absorber x Rear axle carrier New nut
Reused nut (apply engine oil the threads)255
1962,600
2,000188
145
Flexible hose x Shock absorber2930022
ABS speed sensor set bolt8.08271 in.´lbf
ABS speed sensor wire harness x Shock absorber5.55649 in.´lbf
Rear side seatback set bolt1818513
Suspension support x Body3940029
Suspension support x Piston rod4950036
Exhaust center pipe set nut5657041
Parking brake cable set bolt5.45548 in.´lbf
Lower suspension arm x Suspension member1811,850134
Lower suspension arm x Rear axle carrier1811,850134
Strut rod x Body11 31,15083
Strut rod x Rear axle carrier11 31,15083
Suspension member x Body5152038
Suspension member lower stopper sub±assembly x Body3839028
Stabilizer bar bracket x Suspension member1919514
Stabiliser bar link set nut3940029

SS09X±01
SS±62
± SERVICE SPECIFICATIONSBRAKE
225 Author: Date:
BRAKE
SERVICE DATA
Brake pedal height (from asphalt sheet)152.0 ± 162.0 mm (5.984 ± 6.378 in.)
Brake pedal freeplay1 ± 6 mm (0.04 ± 0.24 in.)
Brake pedal reserve distance at 490 N (50 kgf, 110.2 lbf)More than 70 mm (2.76 in.)
Brake booster push rod to piston clearance (w/SST)0 mm (0 in.)
Front brake pad thickness (5S±FE engine) STD12.0 mm (0.472 in.)
Front brake pad thickness (1MZ±FE engine) STD11.0 mm (0.433 in.)
Front brake pad thickness Minimum1.0 mm (0.039 in.)
Front brake disc thickness STD28.0 mm (1.102 in.)
Front brake disc thickness Minimum26.0 mm (1.024 in.)
Front brake disc runout Maximum0.05 mm (0.0020 in.)
Rear brake drum inside diameter STD228.6 mm (9.000 in.)
Rear brake drum inside diameterMaximum230.6 mm (9.079 in.)
Rear brake shoe lining thickness STD5.0 mm (0.197 in.)
Rear brake shoe lining thickness Minimum1.0 mm (0.039 in.)
Rear brake drum to shoe clearance0.6 mm (0.024 in.)
Rear brake pad thickness STD10.0 mm (0.394 in.)
Rear brake pad thickness Minimum1.0 mm (0.039 in.)
Rear brake disc thickness STD10.0 mm (0.394 in.)
Rear brake disc thickness Minimum9.0 mm (0.354 in.)
Rear brake disc runout Maximum0.15 mm (0.0059 in.)
Rear brake disc inside diameter STD170 mm (6.69 in.)
Rear brake disc inside diameter Maximum171 mm (6.73 in.)
Parking brake lining thickness for rear disc brake STD2.0 mm (0.079 in.)
Parking brake lining thickness for rear disc brake Minimum1.0 mm (0.039 in.)
Parking brake lever travel at 196 N (20 kgf, 44 lbf)5 ± 8 clicks
Parking brake clearance between rear shoe and leverLess than 0.35 mm (0.0138 in.)
Parking brake adjusting shim thickness for rear disc brake
0.3 mm (0.012 in.)
0.6 mm (0.024 in.)
0.9 mm (0.035 in.)

SS09Y±03
± SERVICE SPECIFICATIONSBRAKE
SS±63
226 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Master cylinder x Piston stopper bolt101007
Master cylinder x Reservoir1.71816 in.´lbf
Master cylinder x Brake booster131309
Brake line union nut 10 mm nut1515511
12 mm nut2020014
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket131309
Brake pedal x Pedal bracket3940029
Pedal bracket x Instrument panel reinforcement131309
Front brake caliper installation bolt3435025
Bleeder plug8.38574 in.´lbf
Front brake torque plate x Steering knuckle1071,09079
Front brake caliper x Flexible hose2930021
Flexible hose x Shock absorber bracket2930021
Rear drum brake wheel cylinder x Backing plate101007
Parking brake cable bracket x Backing plate7.88069 in.´lbf
Rear brake caliper installation bolt2020014
Rear disc brake cariper main pin installation bolt2627020
Rear brake caliper x Flexible hose2930021
Rear brake torque plate x Rear axle carrier4747534
Proportioning valve installation bolt8.89078 in.´lbf
ABS actuator x Actuator bracket DENSO type5.45548 in.´lbf
ABS actuator x Actuator bracket BOSCH type9.09280 in.´lbf
ABS actuator x ECU BOSCH type2.62723 in.´lbf
ABS & TRAC actuator x Actuator bracket5.45548 in.´lbf
ABS (& TRAC) actuator bracket x Body1919514
Front speed sensor installation bolt7.88069 in.´lbf
Front speed sensor harness clamp bolt5.45548 in.´lbf
Rear speed sensor installation bolt7.88069 in.´lbf
Rear speed sensor harness clamp bolt5.45548 in.´lbf

SS04X±03
SS±10
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT AXLE
Hub nut1031,05076
Steering knuckle x Shock absorber2112,150156
Steering knuckle x Brake caliper1071,09079
Steering knuckle x Tie rod end4950036
Axle hub x Drive shaft2943,000217
Lower ball joint x Lower suspension arm1271,30094
Lower ball joint x Steering knuckle1231,25090
ABS speed sensor set bolt8.08271 in.´lbf
Tie lod end lock nut7475054
FRONT DRIVE SHAFT
Drive shaft center bearing lock bolt3233024
FRONT SUSPENSION
Suspension support x Body8082059
Suspension support x Piston rod4950036
Flexible hose and ABS speed sensor wire harness x Shock absorber2930022
Lower suspension arm set bolt2062,100152
Stabilizer bar link set bolt3940029
REAR AXLE
Hub nut1031,05076
Axle hub set bolt8082059
Shock absorber x Rear axle carrier New nut
Reused nut (Apply engine oil to the threads.)255
1962,600
2,000188
145
No. 1, No. 2 lower suspension arm x Rear axle carrier1811,850134
Strut rod x Rear axle carrier11 31,15083
Flexible hose x Shock absorber2930022
ABS speed sensor set bolt8.08271 in.´lbf
REAR SUSPENSION
ABS speed sensor wire harness x Shock absorber5.45548 in.´lbf
Rear seat outer belt lower side set bolt4243031
Suspension support x Body3940029
Suspension support x Piston rod4950036
Parking brake cable set bolt5.45548 in.´lbf
No. 2 lower suspension arm lock nut5657041
No. 1, No. 2 lower suspension arm x Suspension member1811,850134
Strut rod x Body11 31,15083
Stabilizer bar bracket x Suspension member1919514
Stabilizer bar link set nut3940029

S05523
New Gasket
FI1654
SST
30 cm Fulcrum Length
FI0420
Injector
GrommetO±Ring
Delivery PipeCORRECT
WRONG
± SFI (5S±FE)SFI SYSTEM
SF±3
1436 Author: Date:
(b) When connecting the union bolt on the high pressure pipe
union, observe these procedures:
(1) Always use 2 new gaskets.
(2) Tighten the union bolt by hand.
(3) Tighten the union bolt to the specified torque.
Torque: 29 N´m (300 kgf´cm, 21 ft´lbf)
(c) When connecting the flare nut on the high pressure pipe
union, observe these procedures:
(1) Apply a light coat of engine oil to the flare nut, and
tighten the flare nut by hand.
(2) Using SST, tighten the flare nut to specified torque.
SST 09631±22020
NOTICE:
Do not rotate the fuel pipe, when tightening the flare nut.
Torque: 28 N´m (285 kgf´cm, 21 ft´lbf) for using SST
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(d) Observe these precautions when removing and installing
the injectors.
(1) Never reuse the O±ring.
(2) When placing a new O±ring on the injector, take
care not to damage it in any way.
(3) Coat a new O±ring with spindle oil or gasoline be-
fore installing±never use engine, gear or brake oil.

S05054
New Gasket
FI1654
Fulcrum Length
30 cm
SST
FI6372 FI6372
New O±Ring
Grommet
InjectorCORRECT
WRONG
± SFI (1MZ±FE)SFI SYSTEM
SF±3
1502 Author: Date:
(b) When connecting the union bolt on the high pressure pipe
union, observe these procedures:
(1) Always use 2 new gaskets.
(2) Tighten the union bolt by hand.
(3) Tighten the union bolt to the specified torque.
Torque: 32.5 N´m (330 kgf´cm, 24 ft´lbf)
(c) When connecting the flare nut on the high pressure pipe
union, observe these procedures:
(1) Apply a light coat of engine oil to the flare nut, and
tighten the flare nut by hand.
(2) Using SST, tighten the flare nut to specified torque.
SST 09631±22020
NOTICE:
Do not rotate the fuel pipe, when tightening the flare nut.
Torque: 28 N´m (285 kgf´cm, 21 ft´lbf) for using SST
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(d) Observe these precautions when removing and installing
the injectors.
(1) Never reuse the O±ring.
(2) When placing a new O±ring on the injector, take
care not to damage it in any way.
(3) Coat a new O±ring with spindle oil or gasoline be-
fore installing±never use engine, gear or brake oil.