1999 TOYOTA CAMRY warning

H07517
TOYOTA
Hand±held Tester
DLC2
BR3890
N09348
Hand±held Tester
Break±out±boxECUTOYOTA
TOYOTA
± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
DI±575
810 Author: Date:
(c) Using TOYOTA hand±held tester, check the DTC.
(1) Hook up the TOYOTA hand±held tester to the
DLC2.
(2) Read the DTC by following the prompts on the tes-
ter screen.
Please refer to the TOYOTA hand±held tester oper-
ator 's manual for further details.
(d) Clear the DTC.
(1) Using SST, connect terminals Tc and E
1 of DLC2 or
DLC1.
SST 09843 ± 18020
(2) Turn the ignition switch ON.
(3) Clear the DTC stored in ECU by depressing the
brake pedal 8 or more times within 5 seconds.
(4) Check that the warning light shows the normal
code.
(5) Remove the SST from the terminals of DLC2 or
DLC1.
SST 09843 ± 18020
(e) Using TOYOTA break±out±box and TOYOTA hand±held
tester, measure the ECU terminal values.
(1) Hook up the TOYOTA hand±held tester and
TOYOTA break±out±box to the vehicle.
(2) Read the ECU input/output values by following the
prompts on the tester screen.
HINT:
TOYOTA hand±held tester has a ºSnapshotº function. This re-
cords the measured values and is effective in the diagnosis of
intermittent problems.
Please refer to the TOYOTA hand±held tester/TOYOTA break±
out±box operator's manual for further details.

F02201
DLC1
TsTc E
1
BR3904
0.13 sec. 0.13 sec.
ON
OFF
BR3893
Malfunction Code (Example Code 72, 76)
72 67
ON
OFF
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.1.5 sec.
2.5 sec.4 sec.
Repeat DI±576
± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
811 Author: Date:
2. SPEED SENSOR SIGNAL
(a) Check the speed sensor signal.
(1) Turn the ignition switch OFF.
(2) Using SST, connect terminals Ts and E
1 of DLC1.
SST 09843 ± 18020
(3) Start the engine.
(4) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI±612).
(5) Drive vehicle straight forward.
HINT:
Drive vehicle faster than 45 km/h (28 mph) for several seconds.
(6) Stop the vehicle.
(7) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843 ± 18020
(8) Read the number of blinks of the ABS warning light.
HINT:

See the list of DTC shown on the next page.

If 2 or more malfunctions are indicated at the same time,
the lowest numbered code will be displayed 1st.

If every sensor is normal, a normal code is output (A cycle
of 0.25 sec. ON and 0.25 sec. OFF is repeated).
(9) After doing the check, disconnect the SST from ter-
minals Ts and E
1, Tc and E1 of DLC1, and turn igni-
tion switch OFF.
SST 09843 ± 18020

DI04G±04
F01177
SLIP Indicator Light
TRAC OFF Indicator Light
ABS Warning Light
DLC1
DLC2
Rear Speed Sensor
Sensor Rotor ABS & TRAC ActuatorABS & TRAC ECU
TRAC OFF Switch
ABS & TRAC
Solenoid Relay
ABS & TRAC
Motor RelaySensor Rotor
Front Speed Sensor
Stop Light Switch Front Speed Sensor
DI±580
± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
815 Author: Date:
PARTS LOCATION

DI1JO±03
R05698
A15 A16A17
1 2 3 4 5 6 7 8 9 10
21 11 12 13
14
15 16 17 18 19
20 22 23 24 25 261 2 3 4 5
4 6 7
8
9 10 11 12 13 14 16 151
2 3 5 6
7 8
9 10 11 12
± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
DI±581
816 Author: Date:
TERMINALS OF ECU
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
IG1 (A16 ± 8) ± GND (A15 ±
15, A17 ± 9, 10)B±R e W±BIG switch ON10 ± 14
R+ (A15 ± 1) ± SR (A15 ± 11)GR±R e GRIG switch ON, ABS warning light OFF9 ± 14
R+ (A15 ± 1) ± MR (A15 ± 24)GR±R e GR±LIG switch ONBelow 1.0
SFRR (A15 ± 26) ± GND (A15
± 15, A17 ± 9, 10)W±R e W±BIG switch ON, ABS warning light OFF10 ± 14
SFRH (A15 ± 13) ± GND (A15
± 15, A17 ± 9, 10)R±B e W±BIG switch ON, ABS warning light OFF10 ± 14
SFLR (A17 ± 1) ± GND (A15 ±
15, A17 ± 9, 10)W±L e W±BIG switch ON, ABS warning light OFF10 ± 14
SFLH (A17 ± 2) ± GND (A15 ±
15, A17 ± 9, 10)L±B e W±BIG switch ON, ABS warning light OFF10 ± 14
SRRR (A17 ± 7) ± GND (A15 ±
15, A17 ± 9, 10)R±G e W±BIG switch ON, ABS warning light OFF10 ± 14
SRRH (A17 ± 8) ± GND (A15 ±
15, A17 ± 9, 10)W±R e W±BIG switch ON, ABS warning light OFF10 ± 14
SRLR (A15 ± 12) ± GND (A15 ±
15, A17 ± 9, 10)LG±B e W±BIG switch ON, ABS warning light OFF10 ± 14
SRLH (A15 ± 25) ± GND (A15 ±
15, A17 ± 9, 10)G±Y e W±BIG switch ON, ABS warning light OFF10 ± 14
AST (A15 ± 10) ± GND (A15 ±
15, A17 ± 9, 10)R e W±BIG switch ON, ABS warning light OFF10 ± 14
WA (A16 ± 4) ± GND (A15 ± 15,GBWBIG switch ON, ABS warning light ONBelow 2.0WA (A16 4) GND (A15 15,
A17 ± 9, 10)G±B e W±BIG switch ON, ABS warning light OFF10 ± 14
STP (A16 ± 16) ± GND (A15 ±GWWBStop light switch OFFBelow 1.5STP (A16 16) GND (A15
15, A17 ± 9, 10)G±W e W±BStop light switch ON8 ± 14
D/G (A15 ± 22) ± GND (A15 ±
15, A17 ± 9, 10)R±L e W±BIG switch ON, ABS warning light ON10 ± 14
Tc (A15 ± 9) ± GND (A15 ± 15,
A17 ± 9, 10)LG±R e W±BIG switch ON8 ± 14
Ts (A15 ± 23) ± GND (A15 ± 15,
A17 ± 9, 10)R±Y eW±BIG switch ON8 ± 14
FR+ (A15 ± 17) ± FR± (A15 ±
18)W e BIG switch ON, slowly turn right front wheelAC generation
FL+ (A15 ± 5) ± FL± (A15 ± 4)R e GIG switch ON, slowly turn left front wheelAC generation
RR+ (A16 ± 9) ± RR± (A16 ±
10)W e BIG switch ON, slowly turn right rear wheelAC generation
RL+ (A16 ± 2) ± RL± (A16 ± 1)R e GIG switch ON, slowly turn left rear wheelAC generation

DI04I±04
± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
DI±583
818 Author: Date:
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the DTC check but the problem still occurs, check the circuits for each
problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.
SymptomSuspect AreaSee page
ABS does not operate.
Only when 1. to 4. are all normal and the problem is still
occurring, replace the
ABS & TRAC ECU.
1. Check the DTC reconfirming that the normal code is
output.
2. IG power source circuit
3. Speed sensor circuit
4. Check the ABS & TRAC actuator with a checker. If ab-
normal, check the hydraulic circuit for leakage
(See page DI±623).
DI±574
DI±598
DI±593
BR±61
ABS does not operate efficiently.
Only when 1. to 4. are all normal and the problem is still
occurring, replace the
ABS & TRAC ECU.
1. Check the DTC reconfirming that the normal code is
output.
2. Speed sensor circuit.
3. Stop light switch circuit.
4. Check the ABS & TRAC actuator with a checker. If ab-
normal, check the hydraulic circuit for leakage
(See page DI±623).
DI±574
DI±593
DI±604
BR±61
ABS warning light abnormal.1. ABS warning light circuit
2. ABS & TRAC ECUDI±612
DI±610
DTC check cannot be done.
Only when 1. and 2. are all normal and the problem is still
occurring, replace the ABS & TRAC ECU.
1. ABS warning light circuit
2. TRAC OFF indicator light circuit
3. Tc terminal circuit
DI±612
DI±617
DI±621
Speed sensor signal check cannot be done.1. Ts terminal circuit
2. ABS & TRAC ECUDI±615
DI±610
TRAC does not operate.
Only when inspection circuits for each problem symptom
are all normal and the problem is still occurring, replace the
ABS & TRAC ECU.
1. Check the DTC, reconfirming that the normal code is
output.
2. IG power source circuit
3. Check the hydraulic circuit for leakage
4. Speed sensor circuit
DI±574
DI±598
DI±623
DI±593
SLIP indicator light abnormal.SLIP indicator light circuitDI±620
TRAC OFF indicator light abnormal.
Only when inspection circuits for each problem symptom
are all normal and the problem is still occurring, replace the
ABS & TRAC ECU.
1. TRAC OFF indicator light circuit
2. TRAC cut switch circuit
DI±617
DI±617

DI±610
± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
845 Author: Date:
DTC Always ON ABS & TRAC ECU Malfunction
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
Always ONABS & TRAC ECU internal malfunction is detected.
ECU
Fail safe function:
If any trouble occurs in the power source circuit, the ECU cuts off current to the ABS & TRAC solenoid relay
and prohibits ABS control and TRAC control.
INSPECTION PROCEDURE
1 Is DTC output?
Check DTC on page DI±574.
YES Repair circuit indicated by the code output.
NO
2 Is normal code displayed?
YES Check solenoid relay. Check for short circuit in
harness and connector between solenoid relay
and DLC1 (See page IN±31).
NO
3 Does ABS warning light go off?
YES Check for open and short circuit in harness and
connector between ECU±IG fuse and ABS &
TRAC ECU (See page IN±31).
NO
DI1JQ±03

± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
DI±611
846 Author: Date:
4 Check battery positive voltage.
CHECK:
Check the battery positive voltage.
OK:
10 ± 14 V
NG Check and repair the charging system
5S±FE engine: (See page CH±1)
1MZ±FE engine: (See page CH±1).
OK
5 Check ABS warning light.
PREPARATION:
(a) Disconnect the connector from the ABS & TRAC ECU.
(b) Turn the ignition switch ON.
CHECK:
Check the ABS warning light goes off.
OK Check and replace ABS & TRAC ECU.
NG
Check for short circuit in harness and connector between ABS warning light, DLC1, DLC2, and
ABS & TRAC ECU (See page IN±31)

F00168
BatteryABS & TRAC
Solenoid Relay Engine Room R/B No. 3
3ABS & TRAC
ECU
A8 1
R±L
C 5 4
IG3 IK2 6
J/C C10
EA4ABS Warning Light 8
12 II3
G±B23 2
22 ABS & TRAC
Actuator
DLC1 Short
Pin
WA
J29 33 3 3
3
W±B4
ABS & TRAC
ECUR±L
4
R±L
II3 5
G±B
C C G±B R±LC107
ABS & TRAC ECU R±LR±L
J/C
D 1D
GAUGE Instrument Panel J/B
A16 J4 D
G±B4 W±L
2
DI±612
± DIAGNOSTICSABS & TRACTION CONTROL SYSTEM
847 Author: Date:
ABS Warning Light Circuit
CIRCUIT DESCRIPTION
If the ECU detects a trouble, it lights the ABS warning light while at the same time prohibiting ABS control.
At this time, the ECU records a DTC in memory.
Connect terminals Tc and E
1 of the DLC1 or DLC2 to make the ABS warning light blink and output the DTC.
WIRING DIAGRAM
INSPECTION PROCEDURE
Troubleshoot in accordance with the chart below for each trouble symptom.
ABS warning light does not light upGo to step 1
ABS warning light remains onGo to step 3
1 Check ABS warning light.
See combination meter troubleshooting on page BE±2.
NG Repair bulb or combination meter assembly.
OK
DI04V±04