1999 SUZUKI GRAND VITARA torque

7B1-60 AUTOMATIC TRANSMISSION (4 A/T)
Accumulator piston and spring specification :
Tightening Torque Specification
Used forPiston outer
diameter “a”Spring free length “b”
Direct clutch accumulator (2)31.80 – 31.85 mm
(1.252 – 1.254 in.)Upper spring 43.56 mm (1.715 in.)
Lower spring 30.00 mm (1.181 in.)
Forward clutch accumulator (1)31.80 – 31.85 mm
(1.252 – 1.254 in.)Upper spring 57.18 mm (2.251 in.)
Lower spring 30.50 mm (1.201 in.)
Second brake accumulator (3)34.80 – 34.85 mm
(1.370 – 1.372 in.)Upper spring 56.16 mm (2.211 in.)
Lower spring 18.5 mm (0.728 in.)
Fastening partTightening torque
Nm kg-m lb-ft
Automatic transmission fluid drain plug 23 2.3 17.0
Transfer oil level/filler and drain plugs 23 2.3 17.0
Transmission case plug 17 1.7 12.5
Manual select lever nut 13 1.3 9.5
Manual select cable nut 7 0.7 5.5
Manual selector assembly bolts 18 1.8 13.5
Transmission to engine bolts and nuts 85 8.5 61.5
Engine rear mounting bolts
Engine rear mounting member bolts50 5.0 36.5
Universal joint flange bolts and nuts 50 5.0 36.5
Torque converter mounting bolts 65 6.5 47.0
Adapter case or extension case bolts 42 4.2 30.0
Transmission range switch lock bolt 5.5 0.55 4.0
Oil pipe union bolts 35 3.5 22.5
Drive plate bolts 78 7.8 56.5
Interlock cable clamp screw 2.2 0.22 1.5
Interlock cable outer mounting nut 13 1.3 9.5

DIFFERENTIAL (FRONT) 7E-1
7E
SECTION 7E
DIFFERENTIAL (FRONT)
CONTENTS
General Description ........................................ 7E-2
4WD Control System ..................................... 7E-2
System circuit ............................................ 7E-2
Diagnosis ......................................................... 7E-3
Differential Assembly Diagnosis Table .......... 7E-3
4WD Control System Diagnostic Flow Table 7E-3
Notes on system circuit inspection ............ 7E-3
Flow table .................................................. 7E-4
4WD Control System Circuit Inspection ........ 7E-5
Voltage check ............................................ 7E-54WD Control System Inspection ................... 7E-6
On-Vehicle Service ......................................... 7E-7
Differential Mountings ................................... 7E-7
Rear Mounting for Front Differential Carrier.. 7E-8
Front Differential Assembly ........................... 7E-9
Unit Repair ..................................................... 7E-11
Tightening Torque Specification ................. 7E-11
Special Tool ................................................... 7E-11

NOTE:
For the descriptions (items) not found in this section, refer to the same section of the Service Manual
mentioned in the FOREWORD of this manual.

7E-8 DIFFERENTIAL (FRONT)
6) Position slit in each bush (2) as shown when press-fitting it.
Bush instillation position (angle “A”) :
45
° (slit alignment)
7) Position each bush to bracket as shown in the figure
Bush installation position (length “a”) :
3.0 mm (0.12 in.)
8) Tighten differential front mounting and bracket bolt to speci-
fied torque for reinstallation.
Tightening torque
Front mounting bolt (a) :
85 N·m (8.5 kg-m, 61.5 lb-ft)
Front mounting bracket bolt (b) :
50 N·m (5.0 kg-m, 36.5 lb-ft)
Rear Mounting for Front Differential Carrier
REMOVAL AND INSTALLATION
1) Lift up vehicle and remove rear mounting bracket (3) by
removing rear mounting bolt (1) and rear mounting bracket
bolts (2).
2) Check mounting rubber for damage or deterioration and
replace as necessary.
3) Tighten rear mounting bolts (1) and rear mounting bracket
bolts (2) to specified torque for reinstallation.
Tightening torque
Rear mounting bolt (a) :
85 N·m (8.5 kg-m, 61.5 lb-ft)
Rear mounting bracket bolts (b) :
50 N·m (5.0 kg-m, 36.5 lb-ft)
1. Front mounting bracket L
3. Front mounting bracket R
1. Front mounting bracket R
2. Front mounting bracket L
1, (a)
2, (b)
3

7E-10 DIFFERENTIAL (FRONT)
9) Using 2 large screwdrivers (4) as levers, pull out right side
drive shaft joint (1) from differential (2) and dismount housing
assembly from vehicle.
REMOUNTING
For remounting, reverse dismounting procedure and use the fol-
lowing tightening torque.
Tightening torque
Front drive shaft flange bolts (a) :
50 N·m (5.0 kg-m, 36.5 lb-ft)
Propeller shaft flange bolts (a) :
50 N·m (5.0 kg-m, 36.5 lb-ft)
Front mounting bracket bolts (a) :
50 N·m (5.0 kg-m, 36.5 lb-ft)
Rear mounting bracket bolts(a) :
50 N·m (5.0 kg-m, 36.5 lb-ft)
Rear mounting bolt (b) :
85 N·m (8.5 kg-m, 61.5 lb-ft)
Rear mounting bracket No.2 bolts (b) :
85 N·m (8.5 kg-m, 61.5 lb-ft)
After tightening all fasteners properly, fill hypoid gear oil as speci-
fied and check tightening of plugs with specification.CAUTION:
During above work, use care not to cause damage to
drive shaft boot.
(b) (b)
(a)

DIFFERENTIAL (FRONT) 7E-11
Unit Repair
Refer to the same section of “UNIT REPAIR MANUAL” mentioned in “FOREWORD” of this manual.
Tightening Torque Specification
Special Tool
Fastening partTightening torque
Nm kg-m lb-ft
Front mounting bolts 85 8.5 61.5
Front mounting bracket bolts 50 5.0 36.5
Front drive shaft flange bolts 50 5.0 36.5
Propeller shaft flange bolts 50 5.0 36.5
Rear mounting bolt 85 8.5 61.5
Rear mounting bracket bolts 50 5.0 36.5
Rear mounting bracket No.2 bolts 85 8.5 61.5
09918-18110 09951-16080 09951-26010
Air pressure regulator Bearing installer Bush remover plate

DIFFERENTIAL (REAR) 7F-1
7F
SECTION 7F
DIFFERENTIAL (REAR)
CONTENTS
General Description ........................................ 7F-2
Diagnosis ......................................................... 7F-2
Diagnosis Table ............................................ 7F-2
On-Vehicle Service.......................................... 7F-3
Precaution for Maintenance Service ............. 7F-4
Differential Gear Oil Change ......................... 7F-4
Rear Differential Assembly ............................ 7F-5
Dismounting .............................................. 7F-5
Remounting ............................................... 7F-5
Unit Repair ....................................................... 7F-6Disassembling Unit ....................................... 7F-6
Component Inspection .................................. 7F-9
Sub-Assembly Adjustment and Reassembly 7F-9
Differential carrier .................................... 7F-10
Differential case ...................................... 7F-10
Differential side bearing .......................... 7F-12
Drive bevel pinion.................................... 7F-13
Assembling Unit .......................................... 7F-17
Tightening Torque Specification ................. 7F-20
Required Service Material ............................ 7F-20
Special Tool ................................................... 7F-21

7F-2 DIFFERENTIAL (REAR)
General Description
The differential assembly using a hypoid bevel pinion and gear is installed to the rear axle. It is set in the conven-
tional type axle housing.
The differential assembly is decisive in that the drive power is concentrated there. Therefore, use of genuine
parts and specified torque is compulsory. Further, because of sliding tooth meshing with high pressure between
bevel pinion and gear, it is mandatory to lubricate them by hypoid gear oil.
Diagnosis
Diagnosis Table
Condition Possible Cause Correction
Gear noiseDeteriorated or water mixed lubricant Repair and replenish.
Inadequate or insufficient lubricant Repair and replenish.
Maladjusted backlash between drive bevel pin-
ion and gearAdjust as prescribed.
Improper tooth contact in the mesh between
drive bevel pinion and gearAdjust or replace.
Loose drive bevel gear securing bolts Replace or retighten.
Damaged differential gear(s) or differential pin-
ion(s)Replace.
Bearing noise(Constant noise) Deteriorated or water mixed
lubricantRepair and replenish.
(Constant noise) Inadequate or insufficient
lubricantRepair and replenish.
(Noise while coasting) Damaged bearing(s) of
drive bevel pinionReplace.
(Noise while turning) Damaged differential side
bearing(s) or axle bearing(s)Replace.
Oil leakageClogged breather plug Clean.
Worn or damaged oil seal Replace.
Excessive oil Adjust oil level.

DIFFERENTIAL (REAR) 7F-3
On-Vehicle Service
1. Universal joint flange 9. Differential carrier assembly 17. Bearing adjuster 25. Bolt
2. Hypoid gear set 10. Differential pinion 18. Lock plate 26. Bolt
3. Bevel pinion spacer
Apply thread lock cement
99000-32110 referring to
“DIFFERENTIAL CASE” in
this section.11. Differential gear 19. Pinion shaft No.2 27. Differential case screw :
Apply thread lock
cement 99000-32110 to
thread part of bolt.
4. Shim 12. Pinion shaft No.1 20. Pinion joint Do not reuse.
5. Rear bearing 13. Differential left case 21. Spring washer Tightening torque
6. Front bearing 14. Differential right case 22. Washer Apply differential oil.
7. Oil seal :
Apply grease 99000-25010
to oil seal lip.15. Thrust washer 23. Bevel gear bolt :
Apply thread lock
cement 99000-32110
to thread part of bolt.
8. Flange nut :
After tightening nut so as
rotation torque of bevel pin-
ion shaft to be in specified
value, caulk nut securely.16. Differential side bearing 24. Bolt