1999 SUZUKI BALENO high beam

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

60G-74E
INSTRUMENT PANEL

60G-09-002

CAUTION

If you operate the engine with this

light on, severe engine damage can

result.

Do not rely on the Oil Pressure Light

to indicate the need to add oil. Be

sure to periodically check the engine

oil level (see pages 9-8 and 9-9).
70F-03-009

Charging Light

This light comes on when the ignition switch

is turned on, and goes out when the engine is

started. The light will come on and remain on

if there is something wrong with the battery

charging system. If the light comes on when

the engine is running, the charging system

should be inspected immediately by your

MARUTI dealer.

CAUTION

Do not continue driving long with the

charging light ON as this will drain the

battery 'dead'.
72F-05-027

"Malfunction Indicator" Light

Your vehicle has a computer-controlled

emission control system. A "Malfunction

Indicator" light is provided on the instrument

panel to indicate when it is necessary to have

the emission control system serviced. The

"Malfunction Indicator" light comes on when

the ignition switch is turned to "ON" and goes

out when the engine is started.

If the "Malfunction Indicator" light comes on

when the engine is running, there is a problem

with the emission control system. Take the

vehicle to your MARUTI dealer to have the

problem corrected.

CAUTION

Continuing to drive the vehicle when

the "Malfunction Indicator" light is on

can cause permanent damage to the

vehicle's emission control system, and

can affect fuel economy and

driveability.

5-4

INSTRUMENT PANEL
60G-74E

70F-03-042

Turn Signal Indicators

When you turn on the left or right turn signals,

the corresponding green arrow on the

instrument panel will flash along with the

respective turn signal lights. When you turn

on the hazard warning switch, both arrows will

flash along with all of the turn signal lights.

70F-03-043

Main Beam (High Beam) Indicator Light

This indicator comes on when headlight main

beams (high beams) are turned on.
SPEEDOMETER/ODOMETER/

TRIPMETER (if equipped)

60G-05-003

© Speedometer

© Odometer

(D Trip meter

© Trip meter reset knob

The speedometer indicates vehicle speed in

km/h.The odometer records the total distance

the vehicle has been driven. The tripmeter can

be used to measure the distance travelled on

short trips or between fuel stops. You can reset

the tripmeter to zero by pushing the reset

knob.
CAUTION

Keep track of your odometer reading

and check the maintenance schedule

regularly for required services.

Increased wear or damage to certain

parts can result from failure to perform

required services at the proper mileage

intervals and your warranty rights may

be affected.

5-5

42
41

60G-74E
DRIVING TIPS AND SAFE DRIVING

72F-08-018

72F-08-019

Long distance driving

1. Be sure to perform safety checks before

starting a trip.
2. Take rest at certain intervals to prevent

an accident which may occur when you

are sleepy or tired.
72F-08-020

Night time driving

1. Drive more slowly at night than in the

daytime, for the visual range is restricted

at night.

81

8-8

DRIVING TIPS AND SAFE DRIVING

60G-74E

72F-08-021

2. Don't overtake other vehicles at night.

Darkness bothers your sense of speed

and hinders your judgement on the car-

to-car distance.

3. Don't use the high headlight beam unless

its use is inevitable. Its dazzle may blitz

the driver of the oncoming vehicle, thus

causing an accident.

4. Always keep the window glasses clean.

Don't operate the windshield wiper when

the windshield glass is dry or the wiper

blade and glass may get damaged.
72F-08-022

72F-08-023
MARGIN FOR SAFETY

It is important to allow yourself a margin for

safety during driving so that you can cope with

erroneous or unexpected driving of other

drivers. For that, observe the following.

• Drive at a safe speed.

• Maintain a sufficient distance between

your vehicle and the vehicle ahead.

• Don't force yourself to overtake other

vehicles.

• Don't make quick start, hard steering or

sudden stops.

• Allow an ample time in the driving

schedule.

• Observe traffic rules and regulations.

CONCLUSION

A perfect driver does not exist. The endeavour

of every motorist should be to strive for

perfection. Safety consciousness not only

ensures your safety and the safety of other

road users, it also helps reduce the wear and

tear on your vehicle, prolongs its life, gives

more mileage and ensures a comfortable

driving experience.

Follow the do's and don'ts listed, and

driving will never be the same again.

8-9
82