1999 SUZUKI BALENO ECU

OTHER CONTROLS AND EQUIPMENTS
60G-74E

PARKING BRAKE LEVER

63B-06-001E

The parking brake lever is located between

the seats. To apply the parking brake, hold the

brake pedal down and pull the parking brake

lever all the way up.
63B-06-002E

To release the parking brake, hold the brake

pedal down, pull up slightly on the parking

brake lever, push the button on the end of the

lever with your thumb, and lower the lever to

its original position.
Never drive your vehicle with the

parking brake on: rear brake

effectiveness can be reduced from

over heating, brake life may be

shortened, or permanent brake

damage may result.

If the parking brake does not hold

the vehicle securely or does not fully

release, have your vehicle inspected

immediately by an authorized

MARUTI dealer.

Always apply the parking brake fully

before leaving your vehicle or it may

move, causing injury or damage. When

parking, make sure the gear shift lever

is left in first gear or reverse.

Remember, even though the

transmission is in gear, you must

always apply the parking brake fully.

6-1
54

60G-74E
OTHER CONTROLS AND EQUIPMENT

PEDALS

GEAR LEVER

60G-06-001

Clutch Pedal ©

The clutch pedal is used to disengage the drive

to the wheels when starting the engine,

stopping, or shifting the transmission lever.

Depressing the pedal disengages the clutch.

CAUTION

Do not drive with your foot resting on

the clutch pedal. It could result in

excessive clutch wear, clutch damage,

or unexpected loss of engine braking.
Brake Pedal ®

Your MARUTI vehicle is equipped with front

disc brakes and rear drum brakes. Depressing

the brake pedal applies both sets of brakes.

You may hear occasional brake squeal when

you apply the brakes. This is a normal

condition caused by environmental factors

such as cold, wet, snow, etc.

If brake squeal is excessive and occurs

each time the brakes are applied, you

should have the brakes checked by

your MARUTI dealer.

A WARNING

Do not "ride" the brakes by applying

them continuously or resting your foot

on the pedal. This will result in

overheating of the brakes which could

cause unpredictable braking action,

longer stopping distances, or

permanent brake damage.

Accelerator Pedal ®

This pedal controls the speed of the engine.

Depressing the accelerator pedal increases

power output and speed.
70F-04-005E

The gear change pattern is shown in the

illustration. For details on how to use the

transmission, refer to USING THE

TRANSMISSION in the OPERATING YOUR

VEHICLE section.

55

6-2

OTHER CONTROLS AND EQUIPMENTS

60G-74E

FUEL FILLER CAP

60G-06-002

The fuel filler cap is located on the left rear

side of the vehicle. The fuel filler lid can be

unlocked by pulling up the opener lever located

on the outboard side of the driver's seat and

locked by simply closing the lid.

Remove the fuel filler cap slowly. The

fuel may be under pressure and may

spray out, causing injury.
Petrol Is extremely flammable. Do not

smoke when refuelling, and make sure

there are no open flames or sparks in

the area.
60G-06-OO3

The fuel tank filler cap has a "screw-on ratcheting

type" feature.

• To remove - turn the cap counterclockwise.

Turn the cap slowly to allow any residual

pressure to escape.

• To install - turn the cap clockwise and

tighten it securely until a "ratcheting"

(clicking) sound is heard. The "ratcheting"

sound indicates that the cap is on properly.

6-3
56

60G-74E
OTHER CONTROLS AND EQUIPMENT

FOLDING REAR SEATS

70F-04-008E

If you need to replace the fuel cap, use

only a cap specified for your model.

Using an improper fuel cap can cause

a serious malfunction of the fuel

system. You can get the correct

replacement cap from your MARUTI

dealer.
63B-06-013

The rear seat of your vehicle can be folded

forward ro provide additional luggage space.

To lower the seatback, hook the webbing of

both outboard lap-shoulder belts in the belt

hangers, pull up the lock knobs (© and @)

simultaneously and fold forward the seatback.

To raise the seatback, lift it up and push back

until it locks into place.

When you move a seatback, make sure

the belt webbing is hooked in the belt

hangers (if equipped) so the seat belts

are not caught by the seatback, seat

hinge, or seat latch.This helps prevent

damage to the belt system.
63B-06-014

When returning a rear seat to the

normal position, make sure that

movement of the seatback is

unobstructed and the seatback is

securely latched.

57

6-4

OTHER CONTROLS AND EQUIPMENTS

60G-74E

SUN VISOR
INTERIOR LIGHT SWITCH

70F-04-024

Luggage or other cargo should be

stowed in the luggage compartment

with the rear seat in an upright position,

whenever possible. If you need to carry

cargo in the passenger compartment

with the rear seat back folded forward,

be sure to secure the cargo or it may

be thrown about, causing injury. Never

pile cargo higher than the seatbacks.
The sun visors can be pulled down to block

glare coming through the wind screen, or they

can be unhooked and turned to the side to

block glare coming through the side window.

CAUTION

When unhooking and hooking a sun

visor, be sure to handle it by the hard

plastic parts or the sun visor can be

damaged.
60G-06-004

This light switch has three positions which

function as described below:

© The light comes on and stays on

regardless of whether the door is open or

closed.

© The light comes on when the door is

opened.

® The light remains off even when the door

is opened.

NOTE:

Both Front and Rear doors are involved in

lighting operation of the interior light.

6-5
58

60G-74E
OTHER CONTROLS AND EQUIPMENT

ASSIST GRIPS
BONNET

70F-04-015

Assist grips are provided for passenger

convenience.

Do not hang Herns on the assist grips.

They could obstruct the driver's view,

resulting in an accident, or could be

thrown about in an accident or abrupt

manoeuvre, causing injury.
60G-06-005

To open the bonnet:

1) Pull the bonnet release handle located on

the outboard side of the driver's side of

the instrument panel. This will disengage

the bonnet lock halfway.
60G-06-006

2)
Push the under-bonnet release lever

sideways with your finger, as shown in the

illustration. While pushing the lever, lift up

the bonnet.

59
6-6

OTHER CONTROLS AND EQUIPMENTS

60G-74E

CUP HOLDER (if equipped)
TYRE CHANGING TOOLS

60G-06-007

3)
Continue to lift up the bonnet until it is high

enough to support with the prop rod.

Make sure the bonnet Is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
60G-06-008

To use the cup holder, pull it out fully. After

using the holder, push it back in.

Do not use the cup holder to hold cups

containing hot liquids, or objects other

than cups. Objects in the cup holder

may be thrown about during a sudden

stop or impact, and could cause

personal injury.
60G-06-009

The jack, wheel wrench and jack crank are

stowed in the luggage compartment behind

the rear seat.

To remove the jack, turn its shaft

counterclockwise and pull the jack out of the

storage bracket. To stow the jack, place it in

the storage bracket and turn the shaft

clockwise until the jack is securely held in

place.

6-7
60

60G-74E
OTHER CONTROLS AND EQUIPMENT

LUGGAGE COMPARTMENT TRIM TRUNK (BOOT) LIGHT (if equipped)

Luggage or other cargo placed in the luggage

compartment are hidden from view by a

luggage compartment trim.

Do not carry items on top of the

luggage compartment trim, even if they

are small and light. Objects on top of

the trim could be thrown about In an

accident, causing injury, or could

obstruct the driver's rear view.

60G-06-010
6OG-O6-O11

The jack should be used only to change

wheels. It is important to read the

jacking Instructions in the

EMERGENCY SERVICE section of this

manual before attempting to use the

jack.
When you open the trunk (boot) lid, the trunk

(boot) light comes on and remains on as

long as you keep the lid open.

Do not leave the boot (trunk) lid open

for a long time, or the battery will

discharge.

After using the jack, jack crank and

wheel wrench, be sure to stow them

securely or they can cause injury if an

accident occurs.

61

6-8

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68

60G-74E
INSPECTION AND MAINTENANCE

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ROAD TEST

1. Operation of Brakes, Gear shifting & speedometer

2. Body and Chassis noise

AIR CONDITIONER (if equipped)

1. Check belt tension

2. Check Receiver Drier bubbles.

3. Tighten compressor mounting bolts

4. Check all hose joints, tighten if necessary

5. Check functioning of Recirc flap .*

6. Clean condenser with low pressure water

7. Check belt for frayed edges, change if necessary

8. Check all mounting bolts
FREE

1

1

I

I

I

I

—

I

I

_

-

-
INSPECTIONS

5

6

I

I

I

I

T

I

I

C

I

I
10

12

I

I

I

I

T

I

I

C

I

I
PERIODIC

20

24

I

I

I

I

T

I

I

C

I

I
30

36

I

I

I

I

T

I

I

C

I

I
MAINTENANCE

40

48

I

I

I

I

T

I

I

C

I

I
50

60

I

I

I

I

T

I

I

C

I

I
SERVICE

60

72

I

I

I

I

T

I

I

C

I

I
AT,

70

84

I

I

I

I

T

I

I

C

I

I
COST

80

96

I

I

I

I

T

I

I

C

I

I

The rear shock absorbers are filled with

high pressure gas. Never attempt to

disassemble it or throw it into a fire.

Avoid storing it near a heater or heating

device. When scrapping the absorber,

the gas must be released from the

absorber safely. Ask your dealer for

assistance.

89

9-6

INSPECTION AND MAINTENANCE
60G-74E

All maintenance should be carried

out with the Ignition switch in the

"OFF" position and the car parked

securely on the level ground unless

otherwise specified.

If you are In any way unsure of your

ability to undertake a task, then do

not start it but contact your Maruti

dealer to perform the work for you.
ENGINE OIL AND FILTER

Specified oil

Be sure that the engine oil you use comes

under the API classification of SF, SG or SH.

Select the appropriate oil viscosity according

to the above chart.

9-7
90
70F-07-004E

60G-74E
INSPECTION AND MAINTENANCE

70F-07-029
Do not use any fluid other than SAE

J1703 or DOT-3 brake fluid. Do not

use reclaimed fluid or fluid that has

been stored in old or open

containers. It is essential that foreign

particles and other liquids are kept

out of the brake fluid reservoir.

CAUTION

The brake fluid should be replaced

every two years or 20,000 km.

panel will come on (the engine must

be running with the parking brake

fully disengaged). Should the light

come on, immediately ask your

MARUTI dealer to inspect the brake

system.

A rapid fluid loss Indicates a leak in

the brake system which should be

inspected by your MARUTI dealer

immediately.

Brake fluid can harm your eyes and

damage painted surfaces. Use

caution when refilling the reservoir.
NOTE:

With disc brakes, the fluid level can be

expected to gradually fall as the brake pads

wear.

99
70F-07-030

Brake Pedal

Check if the brake pedal stops at the regular

height without "spongy" feeling when you

depress it. If not, have the brake system

inspected by your MARUTI dealer. If you doubt

the brake pedal for the regular height, check

it as follows:

With the engine running, measure the distance

between the brake pedal and floor wall when

the pedal is depressed with approximately 30

kg (66 lbs) of force. The minimum distance

required is 80 mm (3.1 in). Since your vehicle's

brake system is self-adjusting, there is no need

for pedal adjustment. If the pedal to floor wall

distance as measured above is less than the

minimum distance required, have your vehicle

inspected by your MARUTI dealer.

9-16

INSPECTION AND MAINTENANCE

60G-74E

STEERING

60G-09-015E

NOTE:

When measuring the distance between the

brake pedal and floor wall, be sure not to

include any floor covering in the measurement.

If you experience any of the following

problems with your vehicle's brake

system, have the vehicle inspected

immediately by your MARUTI dealer.

Poor braking performance

Uneven braking (Brakes not working

uniformly on all wheels.)

Excessive pedal travel

Brake dragging

Excessive noise

Pedal pulsation (Pedal pulsates

when depressed.)
63B-09-00SE

Parking brake

Check the parking brake for proper adjustment

by counting the number of clicks made by the

ratchet teeth as you slowly pull up on the

parking brake lever to the point of full

engagement. The parking brake lever should

stop between the 3rd and 5th ratchet tooth

and the rear wheels should be securely locked.

If the parking brake is not properly adjusted

or the brakes drag after the lever has been

fully released, have the parking brake

inspected and/or adjusted by your MARUTI

dealer.
60G-09-016

Check the play of the steering wheel by gently

turning it from left to right and measuring the

distance that it moves before you feel slight

resistance. The play should be between 0 -

30
mm
(0.0 -1.2 in).

Check that the steering wheel turns easily and

smoothly without rattling by turning it all the

way to the right and to the left while driving

very slowly in an open area. If the amount of

free play is outside the specification or you

find anything else to be wrong, an inspection

must be performed by your MARUTI dealer.

9-17

100

60G-74E
INSPECTION AND MAINTENANCE

Hitting curbs and running over rocks

can damage tyres and affect wheel

alignment. Be sure to have tyres and

wheel alignment checked periodically

by your MARUTI dealer.

4) Check for loose wheel nuts.

5) Check that there are no nails, stones, or

other objects sticking into the tyres.

Your MARUTI is equipped with tyres

which are all the same type and size.

This is important to ensure proper

steering and handling of the vehicle.

Never mix tyres of different size or type

on the four wheels of your vehicle. The

size and type of tyres used should be

only those approved by MARUTI as

standard or optional equipment for

your vehicle.
Replacing the wheels and tyres

equipped on your vehicle with certain

combinations of aftermarket wheels

and tyres can significantly change the

steering and handling characteristics

of your vehicle. Therefore, use only

those wheel and tyre combinations

approved by MARUTI as standard or

optional equipment for your vehicle.

CAUTION

Replacing the original tyres with tyres

of a different size may result in false

speedometer or odometer readings.
60G-09-019E

Tyre Rotation

To avoid uneven wear of your tyres and to

prolong their life, rotate the tyres as illustrated.

Tyres should be rotated every 5,000 km as

recommended in the periodic maintenance

schedule. After rotation, adjust front and rear

tyre pressures to the specification listed on

your vehicle's Tyre Inflation Pressure Label.

103

9-20

INSPECTION AND MAINTENANCE

60G-74E

60G-06-009

5)
Changing Wheels

To change a wheel, use the following

procedure:

1) Remove the jack , tools and spare wheel

from the vehicle

2) Loosen, but do not remove the wheel nuts. '

3) Jack up the vehicle (follow the jacking

instructions in the EMERGENCY

SERVICE section in this manual)

4) Remove the wheel nuts and wheel.
60G-09-020E

Install the new wheel and replace the

wheel nuts with their cone shaped end

facing the wheel. Tighten each nut snugly

by hand until the wheel is securely seated

on the hub.

Lower the jack and fully tighten the nuts

[to 8.5 kg-m (61.5 Ib-ft)] in a crisscross

fashion with a wrench as shown in the

illustration.
60G-09-021

Full Wheel Cover (if equipped)

Your vehicle includes a jack crank, which has

a flat end. Use the jack crank to remove the

full wheel cap, as shown above.

9-21
104