1999 SUZUKI BALENO ECU

60G-74E
INSPECTION AND MAINTENANCE

60G-09-026

Always be sure to replace a blown fuse

with a fuse of the correct amperage.

Never use a substitute such as

aluminium foil or wire to replace a

blown fuse. If you replace a fuse and

the new one blows In a short period of

time, you may have a major electrical

problem. Have your vehicle Inspected

immediately by your MARUTI dealer.
60G-09-027E

NOTE:

Make sure that the fuse box always carries

spare fuses.
70F-07-04SE

60G-09-028E

107

9-24

INSPECTION AND MAINTENANCE

60G-74E

BULB REPLACEMENT

Light bulbs can be hot enough to

burn your finger right after being

turned off.This is true especially for

halogen headlight bulbs. Replace

the bulbs after they become cool

enough.

The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

CAUTION

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

CAUTION

Frequent replacement of a bulb

indicates the need for an inspection of

the electrical system. This should be

carried out by your MARUTI dealer.
60G-09-029

Interior Light

Press down the lens by using a plain screw

driver covered with a soft cloth as shown. To

install it, simply push it back in.

The bulb can be removed by simply pulling it

out. When replacing the bulb, make sure that

the contact springs are holding the bulb

securely.
60G-09-030

NOTE:

If the air cleaner inlet duct (A) obstructs

replacement of the bulbs in the right headlight

housing, remove the duct (A).

After reinstalling the duct, make sure it is

secured in place

9-25
108

60G-74E
INSPECTION AND MAINTENANCE

60G-09-033

60G-09-034

60G-09-035

Rear combination light (tail, stop, turn Registration plate tight Trunk (boot) light (if equipped)

signal, etc.) Undo the two screws and remove the light Turn the lens counterclockwise and pull it off.

Undo the screws that secure the housing and housing.

remove the housing by sliding in the direction

of the white arrow in the illustration.

111

9-28

INSPECTION AND MAINTENANCE

60G-74E

WIPER BLADES

60G-09-036

High mount stop light

Trust this replacement job to your authorized

MARUTI dealer.
70F-07-059

If the wiper blades become brittle or damaged,

or make streaks when wiping, replace the

wiper blades.

To install new wiper blades, follow the

procedure below.

CAUTION

To avoid scratching or breaking the

window, do not let the wiper arm strike

the windshield while replacing the

wiper blade.
NOTE:

Some wiper blades may be different from the

ones described here depending on vehicle

specifications. If so consult your MARUTI

dealer for proper replacement method.

The left and the right wiper arm

assemblies are different from each

other. In case you have to remove the

wiper arm assemblies for any reason,

remember not to interchange the two

while fitting them back. Wrong fitment

may lead to windshield breakage.

9-29
112

EMERGENCY SERVICE

60G-74E

JACKING INSTRUCTIONS

60G-06-009

1) Park the vehicle securely on hard level

ground.

2) Apply the parking brake firmly and shift into

"R" (Reverse). Choke the front and rear wheel

diagonally opposite the wheel to be changed.

3) Switch on the hazard warning flasher if your

vehicle is in or near traffic.

4) Slacken but do not remove wheel nuts on the

wheel to be changed.

5) Position the jack vertically and raise the jack

by turning the jack handle clockwise until the

jack head recess fits the frame boss.

6) Continue to raise the jack slowly and smoothly

until the tyre clears the ground. Do not raise

the vehicle more than necessary.

10-1
63B-10-001E

70F-08-001

60G-10-001

NOTE:

Use the wheel nut wrench in combination with

jack crank to raise or lower the jack as shown

in the illustration.
Use the jack only to change wheels.

Never jack up the vehicle on an

inclined surface.

Never raise the vehicle with the jack in

a location other than under the frame

boss near the wheel to be changed.

Make sure that the jack is raised at

least 2 inches (51 mm) before it

contacts the vehicle. Use of the jack

when it is within 2 inches of being

fully collapsed may result in failure

of the jack.

Never get under the vehicle when it

is supported by the jack. t=>

116

60G-74E
EMERGENCY SERVICE

JUMP STARTING INSTRUCTIONS

60G-10-002
60G-10-003

Never run the engine when the

vehicle is supported by the jack and

never allow passengers to remain in

the vehicle.
Never attempt to jump start your

vehicle if the battery appears to be

frozen. Batteries in this condition

may explode or rupture if jump

starting is attempted.

When making jump lead

connections, be certain that your

hands and the Jump leads remain

clear from pulleys, belts, or fans.

Batteries produce flammable

hydrogen gas. Keep flames and

sparks away from the battery or an

explosion may occur. Never smoke

when working in the vicinity of the

battery.

If the booster battery you use for

jump starting is installed in another

vehicle, make sure the two vehicles

are not touching each other.

If your battery discharges

repeatedly, for no apparent reason,

have your vehicle inspected by an

authorized MARUTI dealer.

To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions below

precisely and in order. If you are in

doubt, call for qualified road service.

10-2