1999 SUBARU LEGACY engine

2) Loosen clamps which connect air intake duct to
air intake chamber and mass air flow sensor.
B2M2019
3) Loosen clamp which connects air intake cham-
ber to throttle body.
B2M2769
4) Disconnect blow-by hose and air hoses, and
remove air intake chamber.
B2M2301
5) Disconnect accelerator cable (A).
6) Disconnect cruise control cable (B). (With
cruise control model)
B2M2302A
7) Disconnect connector from throttle position
sensor.
B2M2303
8) Disconnect connector from idle air control sole-
noid valve.
B2M2756
9) Disconnect engine coolant hoses from throttle
body.
B2M2304
10) Remove bolts which install throttle body to
intake manifold.
B2M2305
11) Installation is in the reverse order of removal.
23
[W3A2]2-7SERVICE PROCEDURE
3. Throttle Body

CAUTION:
IAlways use a new gasket.
IBefore installing air cleaner upper cover,
align holes with protruding portions of air
cleaner lower case, then secure upper cover to
lower case.
Tightening torque:
Throttle body:
22
±2 N´m (2.2±0.2 kg-m, 15.9±1.4 ft-lb)
Air intake chamber:
4.9
±0.5 N´m (0.5±0.05 kg-m, 3.6±0.4 ft-lb)
3. 2500 cc MODEL
1) Disconnect battery ground cable.
B2M1723
2) Loosen clamps which connect air intake duct to
air intake chamber and mass air flow sensor.
S2M0080
3) Loosen clamp which connects air intake cham-
ber to throttle body.
S2M0096
4) Disconnect blow-by hose and air hoses, and
remove air intake chamber and air intake duct as
a unit.
S6M0007
5) Disconnect accelerator cable (A).
6) Disconnect cruise control cable (B). (With
cruise control model)
B2M1190A
7) Disconnect connector from throttle position
sensor.
S2M0083
8) Disconnect engine coolant hoses from throttle
body.
B2M1248
24
2-7[W3A3]SERVICE PROCEDURE
3. Throttle Body

16) Disconnect spark plug cords from ignition coil
and ignitor assembly.
B2M2312
17) Disconnect PCV hose assembly from intake
manifold.
B2M2313
18) Disconnect engine coolant hoses from throttle
body.
B2M2299
19) Disconnect brake booster hose.
B2M2314
20) Remove air cleaner case stay RH and engine
harness bracket, and disconnect engine harness
connectors from bulkhead harness connectors.21) Pull out engine harness connector from
bracket.
B2M2315
22) Disconnect connectors from engine coolant
temperature sensor (A) and thermometer (B).
B2M0345B
23) Disconnect knock sensor connector.
B2M2327A
24) Disconnect connector from camshaft position
sensor.
B2M2317B
28
2-7[W4A1]SERVICE PROCEDURE
4. Intake Manifold

18) Disconnect PCV hose (A) and pressure regu-
lator vacuum hose (B) from intake manifold.
19) Disconnect vacuum hose (C) to cruise control
diaphragm. (With cruise control models)
S2M0089A
20) Disconnect engine coolant hose from throttle
body.
B2M2304
21) Disconnect brake booster hose.
B2M2314
22) Remove air intake chamber stay RH, engine
harness bracket from transmission housing, and
disconnect engine harness connectors from bulk-
head harness connectors.
B2M2315
23) Disconnect connectors from engine coolant
temperature sensor (A) and thermometer (B).
B2M0345B
24) Disconnect knock sensor connector.
B2M2327A
25) Disconnect connector from camshaft position
sensor.
B2M2317B
32
2-7[W4A2]SERVICE PROCEDURE
4. Intake Manifold

(3) Remove bolts which secure power steering
pipe brackets to intake manifold.
NOTE:
Do not disconnect power steering hose.
S2M0085
(4) Remove bolts which install power steering
pump to bracket.
B2M2310
(5) Place power steering pump on the right side
wheel apron.
B2M2293
14) Disconnect spark plug cords from ignition coil.
B6M0772
15) Disconnect PCV hose (A) and vacuum hose
(B) from intake manifold.
H2M2440A
16) Disconnect engine coolant hose from throttle
body.
B2M1248
17) Disconnect engine coolant hose (A) from idle
air control solenoid valve.
18) Disconnect air by-pass hose (B) from idle air
control solenoid valve.
H2M1259B
19) Disconnect brake booster hose.
B2M2314
35
[W4A3]2-7SERVICE PROCEDURE
4. Intake Manifold

20) Remove EGR pipe.
S2M0078
21) Remove engine harness bracket from trans-
mission housing, and disconnect engine harness
connectors from bulkhead harness connectors.
S2M0082A
22) Disconnect connectors from engine coolant
temperature sensor (A) and thermometer (B).
B2M0345B
23) Disconnect knock sensor connector.
B2M1243A
24) Disconnect connector from camshaft position
sensor.
S2M0183
25) Disconnect connector from crankshaft position
sensor.
B2M1252A
26) Disconnect connector from oil pressure switch
B2M1253A
27) Disconnect fuel hoses from fuel pipes.
WARNING:
Catch fuel from hoses in a container.
S2M0090A
36
2-7[W4A3]SERVICE PROCEDURE
4. Intake Manifold

28) Remove bolts which hold intake manifold onto
cylinder heads.
S2M0091
29) Remove intake manifold.
B2M0160
B: DISASSEMBLY
1. 2200 cc CALIFORNIA SPEC. VEHICLES
1) Disconnect engine ground terminal from intake
manifold.
B2M2779
2) Disconnect connector from ignition coil and
ignitor assembly.3) Remove ignition coil and ignitor assembly.
B2M2345
4) Disconnect connectors from throttle position
sensor (A), idle air control solenoid valve (B) and
intake manifold pressure sensor (C).
5) Disconnect air by-pass hose (D) from idle air
control solenoid valve.
B2M2346A
6) Remove throttle body.
B2M2300
7) Disconnect connectors from fuel injectors, and
purge control solenoid valve.
37
[W4B1]2-7SERVICE PROCEDURE
4. Intake Manifold

8) Remove harness bands which hold engine har-
ness onto intake manifold.
9) Remove engine harness from intake manifold.
B2M2780A
(A) Fuel injector
(B) Purge control solenoid valve
(C) Harness band
10) Remove purge control solenoid valve.
B2M2782A
11) Remove bolts which install injector pipe on
intake manifold.
B2M2783
12) Remove fuel injectors.
CAUTION:
Replace o-rings and insulators with new ones.
B2M2784
13) Loosen clamp which holds front left side fuel
hose to injector pipe.
B2M2785
14) Remove bolts which hold fuel pipes on the left
side of intake manifold.
B2M2786
15) Remove two bolts which install fuel pipes on
intake manifold.
B2M2787
38
2-7[W4B1]SERVICE PROCEDURE
4. Intake Manifold