1999 Lexus LS400 lexus LS400 1999 Electrical Components / LEXUS 1999 LS400 OWNER'S MANUAL (OM50514U)

COMFORT ADJUSTMENT
201
16L038±1

1Center 2362 mm (14.3 in.) 355 mm (2.2
in.)
452 mm (2.0 in.) 55 mm (0.2 in.)
1. Run your fingers across the trim of the filler panel to
locate the holes underneath it in the positions shown
above.
2. Make a hole in the covering directly above the hole in
the filler panel.

COMFORT ADJUSTMENT
202
16L039
3. R e m o v e t h e s e a l s f r o m t h e a n c h o r s u s i n g a
screwdriver or the like.

COMFORT ADJUSTMENT
203
16L040±1

1Bolt 2Anchor bracket 3Spacer
4. Insert a 15 mm (0.6 in.) spacer, and tighten down the
anchor bracket for your child restraint system with a bolt.
Torque the bolt to 16.5 ± 24.7 N´m (1.68 ±2.52 kgf´m,
12.2 ± 18.2 ft´lbf.).
To comply with Canadian Motor Vehicle Safety
Standards, this model sold in Canada is provided with a
bracket set in the glove box, designed for use with any
of the 3 anchor locations shown in the illustration.
DRIVING POSITION MEMORY SYSTEM
The micro computer can memorize the position of the
driver's seat, the height of the shoulder belt anchor of the
driver's seat belt, and the positions of the tilt and
telescopic steering, and outside rear view mirrors. Two
different driving position profiles can be entered into the
computer's memory.
Recording a driving position in the computer's memory
can only be done when the ignition key is in the ºONº
position and the selector lever is in the ºPº position.
Setting a driving position
16L055

COMFORT ADJUSTMENT
2041. Adjust the driver's seat, driver's shoulder belt
anchor,
tilt and telescopic steering and outside rear
view mirrors to the desired position.
2. While pushing the ºSETº button, push button º1º
or º2º until the signal beeps.
The beep sound means that the positions are recorded
in the computer's memory.
By repeating these two steps and pressing the
remaining button, the driving position for another driver
can be recorded.
To set a new memorized position, select the desired
position and perform step 2. The previous memory will
be erased and the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the
memorized position, then make the desired changes
and perform step 2 above.

COMFORT ADJUSTMENT
205
Activating a memorized position
16L056
When you push button º1º or º2º, the driving
position will be automatically adjusted to the
position recorded for that button.

COMFORT ADJUSTMENT
206Conditions for memorized position activation

Ignition key ºONº and selector lever in ºPº position.
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the
seat position will not change.
 Key not in ignition switch and within 30 seconds of
opening driver's door.
The memorized position can be activated, except for
the tilt and telescopic steering.
If any driving position memory switch is pushed while
one of the memorized driving position profiles is being
activated, the operation will stop.
To activate the system, push the desired button (º1º or
º2º) again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle's battery is disconnected, the computer's
memory will be erased and the memorized positions will
have to be set again.

COMFORT ADJUSTMENT
207
CAUTION
Do not start the vehicle while the adjustments are
being made.
Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch, or depressing the brake
pedal.

SECTION 1 ± 7
208
INSTRUMENTS AND CONTROLS
Theft deterrent
Theft deterrent system208
. . . . . . . . . . . . . . . . . . . . . . . . .
Theft prevention labels 212
. . . . . . . . . . . . . . . . . . . . . . . .
THEFT DETERRENT SYSTEM
To deter theft of the vehicle, this system is designed
to give an alarm if any of the doors, trunk or hood is
forcibly unlocked or the battery terminal is
disconnected and then reconnected while the
vehicle is locked.*
NOTE: *The system operating condition can be
changed. Ask your Lexus dealer for details.
The alarm blows the horn intermittently and flashes the
headlights, tail lights and other exterior lights.