1999 LAND ROVER DISCOVERY handbrake

TRANSFER BOX - LT230SE
41-32 REPAIRS
Refit
1.Fit new input shaft oil seal.

+ TRANSFER BOX - LT230SE,
REPAIRS, Oil seal - input shaft.
2.Clean transfer box to gearbox mating faces.
3.Raise transfer box on jack and align to guide
studs LRT-41-009.
4.Clean transfer box to gearbox bolt threads.
5.Apply sealant, Part No. STC 50552 to bolt and
stud threads.
6.Fit and lightly tighten 2 bolts and nut securing
transfer box to gearbox. If new stud is to be
fitted, apply sealant, Part No. STC 50552 to
stud threads and tighten to 45 Nm (33 lbf.ft).
7.Remove guide studs, fit and lightly tighten 3
bolts.
8.Tighten bolts and nut by diagonal selection to
45 Nm (33 lbf.ft.
9.Position gearbox RH mounting and tighten
bolts to 85 Nm (63 lbf.ft).
10.Tighten gearbox RH mounting nut to 48 Nm
(35 lbf.ft).
11.Fit nut to LH mounting and tighten to 48 Nm (35
lbf.ft).
12.Remove 4 bolts securing support plate to
gearbox jack.
13.Remove 4 bolts securing support plate LRT-99-
010 to transfer box and remove plate.
14.Clean threads of bottom plate bolts.
15.Apply sealant, Part No. STC 50552 to threads
of 4 bottom plate bolts.
16.Fit 4 bolts securing bottom plate and tighten to
25 Nm (18 lbf.ft).
17.Using new washers position breather pipe and
tighten banjo bolt.
18.Connect multiplug to transfer box neutral switch
and secure harness.
19. Up to 03 Model Year - if fitted : Connect
Lucars to differential lock switch and multiplugs
to high/low ratio switch and neutral sensor.
20. 03 Model Year onwards - if fitted: Connect
differential lock warning lamp multiplugs,
secure harness.
21.Connect multiplug to reverse lamp switch.
22. If fitted: Connect Lucars to oil temperature
switch.
23.Position high/low ratio selector cable and
secure with 'C' clip and clevis pin.
24. If fitted: Position differential lock selector cable
to differential lock selector cable abutment
bracket and tighten locknuts sufficiently to
retain cable.
25. If fitted: Fit differential lock selector cable to
transfer gearbox and secure with clevis pin.
26. If fitted: Adjust differential lock selector cable.

+ TRANSFER BOX - LT230SE,
ADJUSTMENTS, Cable - selector -
differential lock - adjust.27. Models fitted with high/low shift interlock
solenoid: Position interlock solenoid harness
to high/low shift cable, fit sleeve around cable
and harness; secure sleeve.
28. Models fitted with high/low shift interlock
solenoid: Connect solenoid multiplug to main
harness and secure multiplug to bracket.
29.Secure cable to fuel pipes with new cable ties.
30.Clean handbrake back plate and mating face.
31.Position handbrake back plate, fit bolts and
tighten to 75 Nm (55 lbf.ft).
32.Clean handbrake drum.
33.Fit handbrake drum and tighten retaining
screw.
34.Fit front propeller shaft.

+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
35.Fit rear propeller shaft.

+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - rear.
36.Clean exhaust silencer and tail pipe mating
faces.
37.Position silencer and secure on mountings,
using a new gasket align to tail pipe, fit nuts
and tighten to 25 Nm (18 lbf.ft).
38.Position rear cross member, fit bolts and
tighten to 26 Nm (19 lbf.ft).
39.Refill transfer box with oil.

+ MAINTENANCE, PROCEDURES,
Transfer box.
40.Fit front exhaust pipe.

+ MANIFOLDS AND EXHAUST
SYSTEMS - V8, REPAIRS, Front pipe.

TRANSFER BOX - LT230SE
41-38 REPAIRS
Seal - rear output shaft
$% 41.20.54
Remove
1.Remove rear propeller shaft.

+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - rear.
2.Loosen brake shoe adjuster bolt.
3.Remove screw securing handbrake drum. 4.Remove handbrake drum.
5.Restrain transfer box drive flange using tool
LRT-51-003. Remove and discard drive flange
nut, remove and discard steel and felt washers.
6.Using tool LRT-99-500 if necessary, remove
drive flange from transfer box.
7.Remove seal from transfer box.

TRANSFER BOX - LT230SE
REPAIRS 41-39
Refit
1.Clean seal mating faces.
2.Fit new seal using tool LRT-41-012.
CAUTION: Oil seal must be fitted dry.
3.Position drive flange, fit new felt and steel
washers.
4.Position tool LRT-51-003 and tighten new
drive flange nut to 148 Nm (109 lbf.ft).
5.Position handbrake drum and tighten screw.
6.Tighten brake shoe adjuster bolt to 25 Nm (18
lbf.ft) then loosen one and a half turns.
7.Check that brake drum is free to rotate.
8.Fit propeller shaft.

+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
9.Top-up transfer box oil.

+ MAINTENANCE, PROCEDURES,
Transfer box.
Gasket - rear output shaft housing
$% 41.20.55
Remove
1.Drain transfer gearbox oil.

+ MAINTENANCE, PROCEDURES,
Transfer box.
2.Remove rear output shaft seal.

+ TRANSFER BOX - LT230SE,
REPAIRS, Seal - rear output shaft.
3.Mark output shaft housing to main casing for
assembly purposes.
4.Note position of shoulder bolt, remove 6 bolts
securing housing to main casing.
Refit
1.Clean output shaft housing, mating face on
main casing and sealant from bolt threads.
2.Apply sealant, Part No. STC 4600 to mating
flange on output shaft housing.
3.Fit output shaft housing to main casing.
4.Apply sealant, Part No. STC 50552 to output
shaft housing bolt threads.
5.Fit output shaft housing bolts and tighten by
diagonal selection to 45 Nm (33 lbf.ft).
6.Fit rear output shaft seal.

+ TRANSFER BOX - LT230SE,
REPAIRS, Seal - rear output shaft.
7.Fill transfer gearbox with oil.

+ MAINTENANCE, PROCEDURES,
Transfer box.

AUTOMATIC GEARBOX - ZF4HP22 - 24
ADJUSTMENTS 44-21
ADJUST ME NTS
Cable - selector
$% 44.30.04
Check
1.Position vehicle on ramp.
2.Select position 'P'.
3.Loosen selector cable trunnion nut.
4.Ensure that gearbox selector lever is in 'P'
position, (fully forward) and tighten trunnion
nut.
5.Lower ramp.
Stall test
$% 44.30.13
Testing
1.Chock the wheels and fully apply the
handbrake.
2.Start the engine and run it until it reaches
normal operating temperature.
3.Apply the footbrake and select 'D'.
4.Fully depress the accelerator pedal and note
the tachometer reading. The figures should be
as given below. Do not carry out stall test for
longer than 10 seconds, and DO NOT repeat
until 30 minutes have elapsed.
lV8: 2200 to 2400 rev/min
lDiesel: 2600 to 2800 rev/min
5.A reading below 1300 rev/min indicates a
torque converter fault, ie stator free-wheel.
6.A reading between 1300 and 2200 rev/min (V8)
or between 1300 and 2600 rev/min (Diesel)
indicates reduced engine power.
7.A reading above 2400 rev/min (V8) or above
2800 rev/min (Diesel) indicates clutch slip.
NOTE: The figures quoted above were
measured at sea level with an ambient
temperature of 20
°C (68°F). At higher altitudes
or higher ambient temperatures, these figures
will be reduced.

AUTOMATIC GEARBOX - ZF4HP22 - 24
44-28 REPAIRS
15.Remove handbrake drum retaining screw and
remove brake drum.
16.Remove 4 bolts from handbrake back plate,
release back plate and tie aside.
17. Models fitted with high/low shift interlock
solenoid: Release interlock solenoid multiplug
and disconnect multiplug from main harness.
18. Models fitted with high/low shift interlock
solenoid: Remove sleeve retaining rings and
remove sleeve from high/low selector cable.
19. If fitted Remove and discard clevis pin
securing differential lock selector cable to
transfer gearbox.20. If fitted Loosen locknuts securing differential
lock selector cable to differential lock selector
cable abutment bracket.
21. If fitted Release and remove differential lock
selector cable from differential lock selector
cable abutment bracket.
22.Remove clevis pin securing high/low ratio
selector cable to selector lever, remove 'C' clip
and remove outer cable from abutment
bracket.
23. Up to 03 Model Year - If fitted: Disconnect
from differential lock warning lamp switch and
multiplugs from high/low ratio switch and
neutral sensor.

AUTOMATIC GEARBOX - ZF4HP22 - 24
REPAIRS 44-31
40.Fit suitable strap to retain torque converter.
Refit
1.Clean gearbox to engine mating faces.
2.Remove torque converter retaining strap.
3.With assistance position gearbox to engine.
4.Fit but do not tighten six bolts securing gearbox
housing to engine.
5.Connect multiplug to gearbox and tighten
locking ring.
6.Connect multiplug to inhibitor switch.
7. If fitted: Connect and adjust differential lock
selector cable.

+ TRANSFER BOX - LT230SE,
ADJUSTMENTS, Cable - selector -
differential lock - adjust.
8.Position selector lever to inhibitor switch and
tighten nut to 25 Nm (18 lbf.ft).
9.Position selector cable to gearbox and secure
with 'C' clip.
10.Clean oil pipe unions and fit new 'O' rings.
11.Position and tighten pipe unions to gearbox.
12.Position and tighten oil cooler pipe clamps.
13.Position and tighten oil cooler pipe clips to
engine sump and alternator bracket.
14.Position engine RH and LH rear mountings
and tighten bolts to 85 Nm (63 lbf.ft) and nuts to
85 Nm (63 lbf.ft).
15.Secure gearbox breather pipes to bulkhead
clip.
16. Up to 03 Model Year - If fitted: Connect 2
Lucars to differential lock warning lamp switch
and multiplugs to high/low ratio switch and
neutral sensor.
17. 03 Model Year onwards - If fitted: Connect
differential lock warning lamp switch multiplugs
to main harness.
18.Position cable tie and multiplug to transfer box
bracket.
19.Connect high/low ratio selector cable to
selector lever and secure with clevis pin. 20.Position high/low ratio selector cable to
abutment bracket and secure with 'C' clip.
21. Models fitted with high/low shift interlock
solenoid: Position interlock solenoid harness
to high/low shift cable, fit sleeve around cable
and harness.
22. Models fitted with high/low shift interlock
solenoid: Connect solenoid multiplug to main
harness and secure multiplug to bracket.
23.Position handbrake backplate and tighten bolts
to 75 Nm (55 lbf.ft).
24.Fit hand brake drum and tighten screw.
25.Remove bolts securing tool LRT-99-008A to
gearbox.
26.Rotate engine to align torque converter, fit new
bolts and tighten to 50 Nm (37 lbf.ft).
27.Fit rear propeller shaft.

+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - rear.
28.Fit front propeller shaft.

+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
29.Fill transfer gearbox with oil.

+ MAINTENANCE, PROCEDURES,
Transfer box.
30.Fill automatic gearbox with oil.

+ MAINTENANCE, PROCEDURES,
Automatic gearbox.
31.Position intermediate silencer and secure to
mounting rubbers.
32.Clean silencer and tail pipe mating faces.
33.Position new gasket to tail pipe and tighten
nuts to 25 Nm (18 lbf.ft).
34.Fit exhaust front pipe.

+ MANIFOLDS AND EXHAUST
SYSTEMS - Td5, REPAIRS, Pipe - front.
35.Fit bolt securing closing plate to gearbox
housing and tighten to 7 Nm (5.2 lbf.ft).
36.Fit upper bolts securing gearbox housing to
engine and tighten to 50 Nm (37 lbf.ft).
37.Fit starter motor.

+ CHARGING AND STARTING,
REPAIRS, Starter motor - diesel.
38.Tighten remaining gearbox housing to engine
bolts to 50 Nm (37 lbf.ft).
39.Connect battery earth lead.
40.Fit battery cover and secure with fixings.
41.Check and adjust selector cable.

+ AUTOMATIC GEARBOX - ZF4HP22
- 24, ADJUSTMENTS, Cable - selector.

BRAKES
DESCRIPTION AND OPERATION 70-19
ABS sensors
The ABS sensors supply the SLABS ECU with a sinusoidal speed signal from each wheel. An inductive sensor,
installed in the hub bearing of each wheel, senses off a 60 tooth exciter ring integrated into the inner race of the hub
bearing. Each ABS sensor has a fly-lead connecting it to the vehicle wiring.
HDC switch
The HDC switch is a latching push switch installed on the fascia, in the switchpack inboard of the steering wheel.
When pushed in, the switch connects an ignition supply to the SLABS ECU to initiate HDC.
Warning indications
The SLABS ECU operates audible and visual warnings to convey brake system status.
Audible warning
A repetitive chime, at a frequency of 2 Hz, draws attention to warning lamp indications. The chime is produced on the
speaker in the instrument pack.
Warning lamps
1ABS warning lamp
2HDC fault warning lamp
3ETC warning lamp4HDC information warning lamp
5Brake warning lamp (all except NAS)
6Brake warning lamp (NAS only)
The following brake system warning lamps can be found in the instrument pack:
lA red brake graphic (all except NAS vehicles) or red BRAKE legend (NAS vehicles), to warn of low brake fluid
level, handbrake on and brake control system failure affecting EBD.
lAn amber ABS graphic, to warn of brake control system failure affecting the ABS function.
lAn amber TC graphic, to warn of brake control system failure affecting the ETC function.
lTwo inclined vehicle graphics, one amber (fault) and one green (information), to indicate operating status of HDC
and to warn of brake control system failure affecting the HDC function.
Each warning lamp is illuminated by a separate LED. The ABS, brake and ETC warning lamps are continuously on
while illuminated; the two HDC warning lamps are either continuously on or flash at a frequency of 2 Hz while
illuminated.

BRAKES
DESCRIPTION AND OPERATION 70-25
DESCRIPTION AND OPERAT ION
Handbrake component layout
1Warning switch
2Handbrake lever
3Cable
4Protective sleeve
5Drum brake6'C' clip
7Threaded sleeve
8Adjuster wheel
9Base plate
10Transmission tunnel