1999 LAND ROVER DEFENDER drain bolt

REAR AXLE AND FINAL DRIVE
1
REPAIR REAR AXLE
Service repair no - 51.25.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
the axle when lowering or repositioning
axle.
1.Drain brake system.
2.Support chassis rear.
3.Remove road wheels.
4.Support axle weight with hydraulic jack.
5.Disconnect shock absorbers.
6.Disconnect flexible brake hose at RH chassis
side member and breather hose at banjo
connection on axle casing.
7.Disconnect lower links at axle.8.Mark differential and propeller shaft flanges with
identification marks for assembly.
9.Remove 4 nuts and bolts, lower propeller shaft
and tie to one side.
10.Disconnect pivot bracket ball joint at axle
bracket.
11.Release bolts and remove coil spring retaining
plates.
12.Lower axle and remove road springs.
13.If applicable, remove anti-roll bar links at axle
See REAR SUSPENSION, Repair. anti-roll
bar.
14.Remove axle assembly.
ProCarManuals.com

REAR AXLE AND FINAL DRIVE
5
REPAIR DIFFERENTIAL ASSEMBLY - 90
Service repair no - 51.15.01
Remove
1.Using suitable container, drain axle oil.
2.Mark differential and propeller shaft flanges to
facilitate reassembly.
3.Remove 4 bolts and disconnect propeller shaft
from differential. Tie aside.
4.Remove 5 hub drive member bolts and withdraw
axle half shafts sufficiently to disengage from
differential unit.
5.Remove 10 nuts securing differential to axle
case.
6.Withdraw differential unit.
NOTE: The differential unit can only be
serviced as a complete assembly with
matching drive pinion. For advice ring
Land Rover Service Department.Refit
7.Ensure mating faces are clean and apply a bead
of RTV sealant to axle case.
8.Support differential unit and position on axle
casing.
9.Secure with self locking nuts and tighten to40
Nm (30lbf/ft).
10.Align marks on flanges and secure propeller
shaft to differential. Tighten bolts to48 Nm (35
lbf/ft).
11.Refit half shafts, using new drive member
gaskets. Tighten bolts to65 Nm (48 lbf/ft).
12.Refill axle oil with approved lubricantSee
LUBRICANTS, FLUIDS AND CAPACITIES,
Information. Recommended lubricants and
fluids.
ProCarManuals.com

FRONT AXLE AND FINAL DRIVE
3
OVERHAUL FRONT STUB AXLE, CONSTANT VELOCITY JOINT
AND SWIVEL PIN HOUSING
Service repair no - 60.15.43.
Remove stub axle, axle shaft and constant
velocity joint.
1.Remove front hub assemblySee FRONT
SUSPENSION, Repair. Front hub bearings.
2.Drain swivel pin housing and refit plug.
NOTE: On later vehicles the swivel pin
housing is filled with grease for life, the
level and drain plugs being deleted.
3.Remove 6 bolts retaining stub axle to swivel
housing.
4.Remove mud shield.
5.Remove stub axle and joint washer.
6.Wthdraw axle shaft and constant velocity joint
from axle casing.
Remove constant velocity joint from axle shaft
7.Hold axle shaft firmly in a soft jawed vice.
8.Using a soft mallet drive constant velocity joint
from shaft.
9.Remove circlip and collar from axle shaft.
Constant velocity joint
10.Mark positions of constant velocity joint, inner
and outer race and cage for reassembly.
11.Swivel cage and inner race to remove balls.
ProCarManuals.com

54FRONT AXLE AND FINAL DRIVE
6
OVERHAUL 38.Place retaining plate, joint washer and oil seal
over axle flange ready for assembly.
39.Fit swivel bearing housing to axle flange with 7
bolts. Tighten to73 Nm (54 lbf/ft).
40.Grease and fit upper and lower swivel pin taper
roller bearings.
41.Position swivel pin housing over swivel bearing
housing.
42.Coat joint washer both sides with sealing
compound and position on lower swivel pin.
43.Loosely fit brake shield bracket plus lower swivel
pin with lug outboard to swivel pin housing.
44.Loosely fit top swivel pin plus existing shims and
brake hose bracket to swivel pin housing.
45.Apply Loctite 270 or equivalent to lower swivel
pin bolts.25 Nm (18 lbf/ft),bend over lock tabs.
46.Tighten top swivel pin bolts to65 Nm (48 lbf/ft).
Check and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to track rod ball joint
bore and pull balance to determine effort
required to turn swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit bolts and
tighten to65 Nm (48 lbf/ft),and bend over lock
tabs.
49.Apply recommended grease between lips of
swivel oil seal.50.Fit oil seal, joint washer and retaining plate with
7 bolts and spring washers. Tighten to11 Nm (8
lbf/ft).
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten fixing to40 Nm (30 lbf/ft).
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to11 Nm (8 lbf/ft).
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.
Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 O’clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle before stub axle is
secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with 6 bolts and
tighten evenly to65 Nm (48 lbf/ft).
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit complete front hub assemblySee FRONT
SUSPENSION, Repair. Front hub bearings.
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil
See MAINTENANCE , Under vehicle
maintenance.
NOTE: On later vehicles fill swivel pin
housing with 0.33 Litres of Molytex EP 00
grease.
67.Set steering lock stop boltsSee STEERING,
Adjustment. Steering lock stops.
ProCarManuals.com

AIR CONDITIONING
1
REPAIR COMPRESSOR
Service repair no - 82.10.20
Remove
1.Remove engine acoustic cover.See ENGINE ,
Repair.
2.Depressurise A/C system.See Adjustment.
3.Remove auxiliary drive belt.See
ELECTRICAL, Repair.
4.Drain cooling system.See COOLING
SYSTEM, Adjustment.
5.Disconnect multiplug from compressor.
6.Remove 2 bolts securing air conditioning pipes
to compressor and discard’O’rings.
CAUTION: Immediately cap all air
conditioning pipes to prevent ingress of
dirt and moisture into the system.
7.Release clips and disconnect top hose from
coolant elbow and heater pipe.
8.Remove 4 bolts securing compressor to
mounting bracket.
9.Remove compressor.Refit
10.Position compressor to mounting bracket and
tighten bolts to25 Nm (18 lbf.ft).
11.Remove caps from compressor and pipe
connections.
12.Clean compressor and pipe connections.
13.Lubricate new’O’rings with refrigerant oil and fit
to compressor.
14.Position A/C pipes to compressor and tighten
bolts to9 Nm (7 lbf.ft).
15.Connect multiplug to compressor.
16.Position top hose and secure with clips.
17.Refill cooling system.See COOLING SYSTEM,
Adjustment.
18.Fit auxiliary drive belt.See ELECTRICAL,
Repair.
19.Recharge A/C system.See Adjustment.
20.Fit engine acoustic cover.See ENGINE ,
Repair.
ProCarManuals.com

82AIR CONDITIONING
6
REPAIR Refit
20.Clean TXV and mating face.
21.Lubricate new’O’rings with refrigerant oil and fit
’O’rings to pipes.
22.Position TXV and tighten Allen screws.
23.Position evaporator and fit sensor.
24.Position cover and tighten screws.
25.Clean pipes and mating faces.
26.Lubricate and fit new’O’rings, position pipes
and tighten Allen screw.
27.Connect trinary switch multiplug.
28.Position blower unit,tighten screws and connect
multiplugs.
29.With assistance position A/C duct assembly to
vehicle.
30.Connect drain pipe to evaporator.
31.Connect multiplug to relay bracket.
32.Align A/C duct to fascia, tighten securing bolt
and screws.
33.Position speakers and connect Lucars.
34.Position relay bracket and tighten bolts.
35.Clean pipes and mating face.
36.Lubricate and fit new’O’rings to evaporator
pipes.
37.Position pipes and tighten bolts to6Nm(4
lbf.ft).
38.Renew receiver drier.See this Section.
39.Recharge A/C system.See Adjustment.
ProCarManuals.com

ELECTRICAL
3
REPAIR ALTERNATOR
Service repair no - 86.10.02
Remove
1.Remove auxilliary drive belt.See this Section.
2.Release cover and remove nut securing lead to
alternator.
3.Disconnect alternator multiplug.
4.Remove bolt (LH thread) and remove auxiliary
drive belt tensioner.
5.Remove bolt securing support stay to alternator.
6.Release clip securing lubrication drain hose to
vacuum pump.
7.Loosen vacuum pump lubrication pipe from
cylinder head and discard’O’ring.
8.Remove bolt securing alternator and release
from mounting bracket.
9.Disconnect hose from vacuum pump.
10.Remove alternator taking care not to damage
radiator cooling fins.
11.Remove 4 bolts, and remove vacuum pump from
alternator.
CAUTION: Plug the connections.
ProCarManuals.com

86ELECTRICAL
4
REPAIR Refit
12.Clean mating face of alternator and vacuum
pump.
13.Fit vacuum pump to alternator and tighten bolts
to10 Nm (7 lbf.ft).
14.Position alternator and connect multiplug.
15.Connect vacuum hose and oil drain hose to
vacuum pump and secure clip.
16.With assistance align alternator to mounting
bracket and fit but do not tighten bolt.
17.Fit bolt securing support stay to alternator and
tighten to25 Nm (18 lbf.ft).
18.Tighten alternator to mounting bracket bolt to45
Nm (33 lbf.ft).
19.Using new’O’ring, fit and tighten lubrication pipe
union to10 Nm (8 lbf.ft).
20.Connect lead to alternator and tighten nut to6
Nm (4.4 lbf.ft).
21.Fit auxilliary drive belt tensioner and tighten bolt
to50 Nm (37 lbf.ft).
22.Fit auxilliary drive belt.See this Section.HORN - LH
Service repair no - 86.30.10
Remove
1.Remove LH headlamp.See this Section.
2.Disconnect horn multiplug.
3.Remove nut and remove horn from mounting
bracket.
Refit
4.Position horn, tighten securing and connect
multiplug.
5.Fit LH headlamp.See this Section.
ProCarManuals.com