Page 32 of 343

Protecting Children
Installing a Rear-Facing Child Seat with a Lap/Shoulder Belt
The lap/shoulder belts in the outer back seats have a lockingmechanism that must be activated to
secure a child seat.
The following pages provide instructions on how to secure a rear-
facing child seat with this type ofseat belt.
See page 33 for how to secure a rear-
facing child seat in the center
position of the third seat with the lap
part of the lap/shoulder belt.
For tips on installing a rear-facingchild seat with either type of seat
belt, see page 34 . 1. With the child seat in the desired
back seating position, route the
belt through the child seataccording to the seat maker's
instructions, then insert the latch plate into the buckle. 2. To activate the lockable retractor,
slowly pull the shoulder part of the
belt all the way out until it stops,
then let the belt feed back into the
retractor (you might hear a clicking noise as the belt retracts).
CONTINUED
Driver and Passenger SafetyProCarManuals.comMain Menu Table of Contents s t
Page 33 of 343
Protecting Children
3. After the belt has retracted, tug on it. If the belt is locked, you will not
be able to pull it out. If you can pull
the belt out, it is not locked and you will need to repeat these steps.
4. After confirming that the belt islocked, grab the shoulder part of
the belt near the buckle and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child scat will not be secure.
To remove slack, it may help to put weight on the child seat, or
push on the back of the scat, while
pulling up on the belt. 5. Push and pull the child seat
forward and from side to side to
verify that it is secure enough to stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to retract fully, then repeat these
steps.
Driver and Passenger SafetyProCarManuals.comMain Menu Table of Contents s t
Page 34 of 343
Protecting Children
To deactivate the locking mechanism and remove a child seat,
unlatch the buckle, unroute the seat
belt, and let the belt fully retract. Installing a Rear-Facing Child Seat in
the Center Position of the Third Seat
To install a rear-facing child seat in the center position of the third seat,
use the lap part of the lap/shoulderbelt. Follow instruction number 1 on
page 31 for routing and latching theseat belt.
Then pull hard on the loose end of the belt to remove any slack (it may
help to put weight on the child seat
while pulling on the belt). Finally, follow instruction number 5
on page 32 to verify that the child
seat is secure.
CONTINUED
Driver and Passenger SafetyProCarManuals.comMain Menu Table of Contents s t
Page 37 of 343

Protecting Children
If it is necessary to put a forward-
facing child seat in the front, move
the vehicle seat as far to the rear as
possible, be sure the child seat is firmly secured to the vehicle, and the
child is properly strapped in the seat.
Installing a Child Seat with a Lap/
Shoulder Belt
The lap/shoulder belts in the outer back and front passenger seating
positions have a locking mechanism
that must be activated to secure a
child seat.
The following pages provide instructions on how to secure a
forward-facing child seat with this type of seat belt.
See page 38 for how to secure a
forward-facing child seat in the
center position of the third seat with
the lap part of the lap/shoulder belt. 1. With the child seat in the desired
seating position, route the belt
through the child seat according
to the seat maker's instructions,
then insert the latch plate into the
buckle.
Driver and Passenger Safety
Improperly placing a forward-
facing child seat in the front seat can result in serious injury
or death if the airbags inflate.
If you must place a forward-
facing child seat in front, move
the vehicle seat as far back as possible and properly restrain
the child.ProCarManuals.comMain Menu Table of Contents s t
Page 38 of 343

Protecting Children
2. To activate the lockable retractor, slowly pull the shoulder part of the
belt all the way out until it stops, then let the belt feed back into theretractor (you might hear a
clicking noise as the belt retracts).
3. After the belt has retracted, tug on it. If the belt is locked, you will not
be able to pull it out. If you can pullthe belt out, it is not locked and
you will need to repeat these steps. 4. After confirming that the belt is
locked, grab the shoulder part of
the belt near the buckle and pull
up to remove any slack from the
lap part of the belt. Remember, if the lap part of the belt is not tight,
the child seat will not be secure. It may help to put weight on the
child seat, or push on the back of
the seat, while pulling up on the belt. 5. Push and pull the child seat
forward and from side to side to
verify that it is secure enough to stay upright during normal drivingmaneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract fully, then repeat these
steps.
CONTINUED
Driver and Passenger SafetyProCarManuals.comMain Menu Table of Contents s t
Page 39 of 343
Protecting Children
To deactivate the locking
mechanism and remove a child seat, unlatch the buckle, unroute
the seat belt, and let the belt fully retract. Installing a Child Seat in the Center
Position of the Third Seat
To install a forward-facing child seat in the center position of the third
seat, use the lap part of the lap/
shoulder belt. Follow instructionnumber 1 on page 36 for routing and
latching the seat belt.
Then pull hard on the loose end of the belt to remove any slack (it may
help to put weight on the child seat
while pulling on the belt). Finally, follow instruction number 5 on page 37 to verify that the child
seat is secure.
Driver and Passenger SafetyProCarManuals.comMain Menu Table of Contents s t
Page 43 of 343

Protecting Children
Physical Size
Physically, a child must be large
enough for the lap/shoulder belt to
properly fit over the hips, chest, and shoulder (see pages 15 and 39). If
the seat belt does not fit properly,
the child should not sit in the front.
Maturity
To safely ride in front, a child must be able to follow the rules, includingsitting properly and wearing the seat
belt properly throughout a ride. If you decide that a child can safely
ride up front, be sure to: Carefully read the owner's manual
and make sure you understand all seat belt instructions and all safety
information. Move the vehicle seat to the rear-
most position. Have the child sit up straight, back
against the seat, and feet on or
near the floor.
Check that the child's seat belt is
properly positioned and secured. Supervise the child. Even mature
children sometimes need to be
reminded to fasten the seat belts or sit properly.
Driver and Passenger SafetyProCarManuals.comMain Menu Table of Contents s t
Page 44 of 343

Protecting ChildrenUsing Child Seats with Tethers
Your vehicle has attachment points
for a tether-style child seat to beinstalled on the second or third row
as shown.
Since a tether can provide additional
security, we recommend using a
tether whenever one is required or
available. (Tethers are required in Canada. U.S. owners may check with
the child seat maker to determine
whether a tether is available for a
particular child seat.) Second Seat Installation:
There are two attachment points available for the second seat.
To use a tether-style child seat in the second seat, the third seat must be
stored in the floor recess (see page110). Select the attachment point
you want to use. Remove the plug
with a small flat-tipped screwdriver or fingernail file.
Important Safety Information
Keep the third seat in the floor while
using a tether-style child seat in the second seat. If you attempt to return
the third seat to the upright position,
you may damage the vehicle or tether, even though the damage maynot be obvious. If this happens, the
child seat may not be properly
restrained in a crash.
CONTINUED
Driver and Passenger Safety
ProCarManuals.comMain Menu Table of Contents s t