yellowblue
7-19
(10) = Check clutch pedal for free travel. Press pedal
by hand until resistance is felt. Free travel should be
maintained at 1.5 to 2 inches (38 to 51 mm) measured
at the clutch pedal pad. Make checks at 3,000 miles
(5 000 km) and 6,000 miles (10 000 km) and then every
6,000 miles (10 000 km) thereafter.
(11) = Inspect rear axle air shift motor for fluid leaks.
Remove plug to check fluid level. Inspect air lines and
hoses for proper hook
-up, binding, leaks, etc. Inspect at
3,000 miles (5 000 km) and 24,000 miles (40 000 km)
and then every 24,000 miles (40 000 km) thereafter.
(12) = Chassis Lubrication Service: Lubricate all grease
fittings in front suspension, front axle and steering
linkage. DO NOT lubricate kingpin bushings with air
pressure equipment; instead, use a hand grease gun to
ensure complete purge and eliminate sealer cap
distortion. Lubricate transmission and shift linkage,
hood latches and hood hinges, parking brake lever pivot,
clevis pins and linkage, disc brake caliper rails, clutch
linkage and release bearing (if equipped), propeller shaft
slip joint, universal joint, brake camshaft bracket, slack
adjusters, pedal shaft, clutch cross shaft and clutch pedal
springs. Lubricate suspension, axle and steering linkage
more often when operating under dusty or muddy
conditions and in excessive off
-road use.(13) = Check steering system:
Look for damaged, loose or missing parts. Also
look for parts showing signs of wear or lack of
lubrication. Replace parts as needed. Also check
steering gear mounting bolts, pitman arm nut, gear
housing upper cover and side cover attaching bolts,
steering column mounting bolts and cardan
joint clamp bolts; tighten if necessary.
(See service manual.)
Inspect power steering hoses, tubes and fittings for
leaks. Hoses and lines must not be twisted, kinked or
tightly bent. Make sure clips, clamps, supporting
tubes and hoses are in place and properly secured.
Check steering gear for leakage around pitman shaft
and housing. If leakage is evident (lubricant
oozing out, not just oily film), leak should be
corrected immediately.
(14) = Check front and rear suspension. Look for
damaged, loose or missing parts or parts showing signs
of wear or lack of lubrication. Replace parts as needed.
(15) = Adjust tire pressures as indicated on the
Certification/Tire label for optimum tire life. See ªTiresº
in the Index for further details. Check tires for excessive
or abnormal wear or damage. Also check for damaged
wheels. Replace wheels and/or tires as needed.
ProCarManuals.com
yellowblue
7-27
Door Latches Check
Check that doors close, latch and lock tightly. Check for
broken, damaged or missing parts that might prevent
tight latching.
Hood Latches Check
Check that the hood closes firmly. Check for broken,
damaged, loose or missing parts that might prevent tight
latching. Make sure the secondary latch (if equipped)
keeps the hood from opening all the way when the
primary latch is released.
Fluid Leaks Check
Check for fuel, coolant, oil or other fluid leaks by
looking at the surface beneath the vehicle after it has
been parked for a while.
Underbody Inspection
Corrosive materials used for ice, snow removal and dust
control can collect on the underbody. If these materials
are not removed, accelerated corrosion (rust) can occur
on underbody parts such as fuel lines, frame, floor pan
and exhaust system. At least every spring, flush these materials from the underbody with plain water. Take
care to clean well any areas where mud and other debris
can collect. Sediment packed in closed areas of the
frame should be loosened before being flushed.
Engine Cover Check
Check that the cab's engine cover and seal (if equipped)
are not torn or damaged. Be sure that the cover is bolted
down firmly to the floor.
At Least Once a Year
Key Lock Cylinders Service
Lubricate the key lock cylinders with the lubricant
specified in Part C.
Underbody Flushing Service
At least every spring, use plain water to flush any
corrosive materials from the underbody. Take care to
clean thoroughly any areas where mud and other debris
can collect.
Tractor Protection (Breakaway) Valve Check
On air brake models, remove, disassemble, clean and
inspect the tractor protection (breakaway) valve.
ProCarManuals.com
