1999 GMC C-SERIES ignition

yellowblue
2-69 Transmission Temperature Gage
(If Equipped)
If you have an automatic
transmission and this gage,
it is to the right of the dash
mounted shift lever, just to
the right of your
floor
-mounted shift lever or
on the lower portion of the
instrument panel to the right
of the steering wheel.
When your ignition is on, the gage shows the
temperature of the transmission oil. A reading in the
warning zone means you must stop driving and check
into the cause. One possible cause is a low oil level in
the transmission.
NOTICE:
If you drive when the transmission temperature
gage is in the warning zone, you can badly
damage the transmission.
Air Pressure Gage (If Equipped)
If your vehicle has air
brakes, this gage at the
center of your instrument
cluster shows the air
pressure for both your front
and rear brake systems.
If the needle on the gage indicates that the air pressure is
below 60 psi (415 kPa), the LOW AIR warning light
will come on. An alarm will also sound if this happens.
The yellow pointer shows the pressure available for the
front system, while the green pointer shows pressure for
the rear. There should be no more than 4 psi (28 kPa)
difference showing between the systems.
Don't drive until both pointers are showing at least
120 psi (830 kPa), so you'll have enough air if you need
to apply your brakes.
ProCarManuals.com

yellowblue
4-23
CAUTION:
Coasting downhill in NEUTRAL (N) or with the
ignition off is dangerous. Your brakes will have to
do all the work of slowing down. They could get
so hot that they wouldn't work well. You would
then have poor braking or even none going down
a hill. You could crash. Always have your engine
running and your vehicle in gear when you
go downhill.

Know how to go uphill. Use lower gears. They help
cool your engine and transmission, and you can
climb the hill better.
Stay in your own lane when driving on two
-lane
roads in hills or mountains. Don't swing wide or cut
across the center of the road. Drive at speeds that let
you stay in your own lane.

As you go over the top of a hill, be alert. There
could be something in your lane, like a stalled car
or an accident.

You may see highway signs on mountains that warn
of special problems. Examples are long grades,
passing or no
-passing zones, a falling rocks area,
winding roads and special truck lanes. Be alert to
these and take appropriate action.
ProCarManuals.com

yellowblue
5-3 Hazard Warning Flasher Switch
(If Equipped)
With some options, such as U86-trailer wiring or
RQ3
-tractor application, you will have this switch.
This switch replaces the hazard switch mounted on the
steering column. It is mounted in the instrument panel,
usually to the left of and below the steering column.
Pull the switch out to make your front and rear turn
signal lamps flash on and off. A light next to the switch
will also flash. Push it back in to turn off the flashers.
The turn signal lamps won't flash if you're braking.
This switch works no matter what position the key is in,
and even if the key isn't in the ignition.
When the hazard warning flashers are on, your turn
signals won't work.
ProCarManuals.com

yellowblue
5-6
If you have a diesel engine vehicle with two batteries
(or more), you should know before you begin that,
especially in cold weather, you may not be able to
get enough power from a single battery in another
vehicle to start your diesel engine.
If your vehicle has more than one battery, use the
battery that's closest to the starter
-- this will reduce
electrical resistance.
CAUTION:
If your vehicle has air conditioning, the auxiliary
electric fan under the hood can start up even
when the engine is not running and can injure
you. Keep hands, clothing and tools away from
any underhood electric fan.
2. Get the vehicles close enough so the jumper cables
can reach, but be sure the vehicles aren't touching
each other. You wouldn't be able to start your
vehicle, and the bad grounding could damage the
electrical systems.
3. Turn off the ignition on both vehicles. Turn off all
lamps that aren't needed, as well as radios. This willavoid sparks and help save both batteries, and it
could save your radio.
4. Locate the batteries on each vehicle. Find the
positive (+) and negative (
-) terminals on
each battery.
CAUTION:
Using a match near a battery can cause battery
gas to explode. People have been hurt doing this,
and some have been blinded. Use a flashlight if
you need more light.
Be sure the batteries have enough water. You
don't need to add water to the ACDelco
Freedom

battery (or batteries) installed in
every new GM vehicle. But if a battery has filler
caps, be sure the right amount of fluid is there.
If it is low, add water to take care of that first.
If you don't, explosive gas could be present.
Battery fluid contains acid that can burn you.
Don't get it on you. If you accidentally get it in
your eyes or on your skin, flush the place with
water and get medical help immediately.
ProCarManuals.com

yellowblue
6-16 Engine Oil Additives
Don't add anything to your oil. Your dealer is ready to
advise if you think something should be added.
When to Change Engine Oil
Your vehicle has a computer that lets you know when to
change your engine oil. This is not based on mileage,
but on engine revolutions and engine operating
temperature. When the computer has calculated that the
oil needs changing, the Oil Life Monitor will indicate
that a change is necessary. The mileage between oil
changes will vary depending on how you drive your
vehicle
-- usually between 3,000 miles (5 000 km) and
7,500 miles (12 500 km) since your last oil change.
Under severe conditions, the indicator may come on
before 3,000 miles (5 000 km). Never drive your vehicle
more than 7,500 miles (12 500 km) or 12 months
(whichever occurs first) without an oil change.
The system won't detect dust in the oil. So, if you
drive in a dusty area, be sure to change your oil every
3,000 miles (5 000 km) or sooner. Remember to reset
the CHANGE OIL light whenever the oil is changed.How to Reset the Oil Life Monitor
To reset the CHANGE OIL message, turn the ignition
key to RUN with the engine off. Fully press and release
the accelerator pedal three times within 10 seconds. If
the CHANGE OIL message flashes for five seconds, the
system is reset. If the message does not display for five
seconds, you will need to reset the system again.
What to Do with Used Oil
Did you know that used engine oil contains certain
elements that may be unhealthy for your skin and could
even cause cancer? Don't let used oil stay on your skin
for very long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly throw
away clothing or rags containing used engine oil. (See
the manufacturer's warnings about the use and disposal
of oil products.)
Used oil can be a real threat to the environment. If you
change your own oil, be sure to drain all free
-flowing oil
from the filter before disposal. Don't ever dispose of oil
by putting it in the trash, pouring it on the ground, into
sewers, or into streams or bodies of water. Instead,
recycle it by taking it to a place that collects used oil. If
you have a problem properly disposing of your used oil,
ask your dealer, a service station or a local recycling
center for help.
ProCarManuals.com

yellowblue
6-31
CAUTION:
Don't add brake fluid before you check the level.
If you do, you could get too much brake fluid.
Brake fluid could spill on the hot engine and it
can catch fire. You could be burned and your
vehicle could be damaged.
Checking Brake Fluid
Apply the brake pedal several times with the ignition
off. Then clean one of the reservoir caps and the area
around the cap, and remove it. The fluid level should be
even with the bottom ring of the filler opening.
If it's low, add enough fluid
to fill the reservoir to the
proper level.
What to Add
Use the proper fluid listed in your Maintenance
Schedule. Use new brake fluid from a sealed
container only.
Always clean the brake fluid reservoir cap and the area
around the cap before removing it. This will help keep
dirt from entering the reservoir.
ProCarManuals.com

yellowblue
6-72
Maxi-Fuse Block
When a circuit goes out, first check the instrument panel
circuit breaker block. If no circuit breakers are out there,
the problem could in the maxi
-fuse block.
This block uses blade
-type fuses. It's on the upper
passenger side of the engine compartment at the rear.
To access the maxi-fuse block, gently squeeze both
sides of the cover to unlatch the tabs at the top. Then,
unsnap both attachments at the bottom and remove
the cover.
Power is fed through these fuses to devices such as the
headlamp switch, ignition switch feed circuits and the
auxiliary brake pump (hydraulic brake vehicles).
Be sure to replace maxi
-fuses with maxi-fuses of the
same rating. Do not use maxi
-fuses of higher amperage
than those indicated on the maxi
-fuse block.
ProCarManuals.com

yellowblue
6-73
Name Circuits/Circuit Breakers
Protected
STP/HAZ
TURNStop Lamp, Turn Signal/Hazard
Lights, Fuel, Ignition Relay
(Gasoline Engines)
IGN SW3 Air Conditioner, Ignition Switch,
Axle, ChassisName Circuits/Circuit Breakers
Protected
INT/EXT
LIGHTSParking Lamps,
Dome/Panel Lights
HEAD LAMP Headlamps,
Daytime Running Lamps
AUX WRG Auxiliary, Park Brake
IGN SW1 Ignition Switch, Wash/Wipe,
Crank, Radio
HYD PUMP Hydraulic Brake,
Brake Pump Motor
HYD ABS EHCU
PWR
WDO/LCKSWindow, Door Locks
PARK BRK Parking Brake Motor
BLOWER
HORNBlower, Horn, Cigarette
Lighter/Auxiliary
FUEL/ENGINE Empty
ProCarManuals.com