1999 FORD TAURUS radio controls

²-Distributes outside air through the instrument
panel registers and the floor ducts. Heating and air
conditioning capabilities are provided in this mode.
The air will be heated or cooled based on the
temperature selection. For added customer comfort,
the air distributed through the floor ducts will be
slightly warmer than the air sent to the instrument
panel registers.
²MAX A/C-Uses recirculated air to cool the vehicle.
The temperature will remain unchanged and air will
be cooled based on the selected temperature. To
exit, press AUTOMATIC or any other override
controls. MAX A/C is noisier than normal A/C but
more economical and will cool the inside of the
vehicle faster. Airflow is from the instrument panel
registers. This mode can also be used to prevent
undesirable odors from entering the vehicle.
²OFF-Outside air is shut out and the fan will not
operate. For short periods of time only, use this
mode to reduce undesirable odors from entering
the vehicle.
Displaying outside temperature
Press OUTSIDE TEMP
to display the outside
air temperature. It will
be displayed until
OUTSIDE TEMP is
pressed again or until
any other control is
pressed. When the
EATC system is off and OUTSIDE TEMP is pressed,
the outside temperature will only be displayed for
four seconds.
The outside temperature reading is most accurate
when the vehicle is moving. Higher readings may be
obtained when the vehicle is not moving. The
readings that you get may not agree with
temperatures given on the radio due to differences
in vehicle and station locations.
OFFAUTO
TEMPOUT
SIDE
A/C MAX
VENT
Controls and features
27

If the volume is set above a certain level and the
ignition is turned off, the volume will come back on
at a ªnominalº listening level when the ignition
switch is turned back on. If you wish to maintain
your preset volume level, turn the audio system off
with the power control before switching off the
ignition.
AM/FM select
The AM/FM select
control works in radio
mode.
AM/FM select in radio mode
This control allows you to select AM or FM
frequency bands. Press the control to switch
between AM, FM1 or FM2 memory preset stations.
Tune adjust
The tune control works
in radio.
Tune adjust in radio mode
²Press theto move to the next frequency down
the band (whether or not a listenable station is
located there). Hold the control to move through
the frequencies quickly.
²Press the right side of the control to move to the
next frequency up the band (whether or not a
listenable station is located there). Hold for quick
movement.
Seek function
The seek function
control works in radio
mode.
AM
FM
VOL
PUSH-ON
TUNE
SEEK
Controls and features
30

Seek function in radio mode
²Pressto find the next listenable station down
the frequency band.
²Press
to find the next listenable station up the
frequency band.
Scan function
The scan function
works in radio mode.
Scan function in radio mode
Press the SCAN control to hear a brief sampling of
all listenable stations on the frequency band. Press
the control again to stop the scan mode.
Radio station memory preset
The radio is equipped with six station memory
preset controls. These controls can be used to select
up to six preset AM stations and twelve FM stations
(six in FM1 and six in FM2).
Setting memory preset stations
1. Select the frequency
band with the AM/FM
select control.
2. Select a station.
Refer toTune adjust
orSeek functionfor
more information on selecting a station.
SCAN
AM
FM
VOL
PUSH-ON
123456
Controls and features
31

Volume/power control
Press the control to
turn the audio system
on or off.
Turn control to raise or
lower volume.
If the volume is set above a certain level and the
ignition is turned off, the volume will come back on
at a ªnominalº listening level when the ignition
switch is turned back on. If you wish to maintain
your preset volume level, turn the audio system off
with the power control before switching off the
ignition.
AM/FM select
The AM/FM select
control works in radio,
tape and CD modes (if
equipped).
AM/FM select in radio mode
This control allows you to select AM or FM
frequency bands. Press the control to switch
between AM, FM1 or FM2 memory preset stations.
AM/FM select in tape mode
Press this control to stop tape play and begin radio
play.
VOL
PUSH-ON
VOL
PUSH-ON
AM
FM
VOL
PUSH-ON
Controls and features
34

AM/FM select in CD mode
Press this control to stop CD play and begin radio
play.
You can switch from CD play to tape play by simply
inserting a tape into the cassette deck.
Tune adjust
The tune control works
in radio or CD mode.
Tune adjust in radio mode
²Pressto move to the next frequency down the
band (whether or not a listenable station is
located there). Hold the control to move through
the frequencies quickly.
²Press
to move to the next frequency up the
band (whether or not a listenable station is
located there). Hold for quick movement.
Tune adjust for CD mode
²Press theto select the previous disc in the CD
changer. (Play will begin on the first track of the
disc unless the CD changer is in shuffle mode.
Refer toShuffle featurefor more information.
Hold the control to continue reversing through
the disc.
²Press
to select the next disc in the CD
changer. Hold the control to fast-forward through
the remaining discs.
Seek function
The seek function
control works in radio,
tape or CD mode.
Seek function in radio mode
²Pressto find the next listenable station down
the frequency band.
TUNE
DISC 1-6
SEEK
Controls and features
35

²Pressto find the next listenable station up the
frequency band.
Seek function in tape mode
²Pressto listen to the previous selection on the
tape.
²Press
to listen to the next selection on the
tape.
Seek function in CD mode
²Pressto seek to the previous track of the
current disc. If a selection has been playing for
three seconds or more and you press
, the CD
changer will replay that selection from the
beginning.
²Press
to seek forward to the next track of the
current disc. After the last track has been
completed, the first track of the current disc will
automatically replay.
Scan function
The scan function
works in radio, tape or
CD mode.
Scan function in radio mode
Press the SCAN control to hear a brief sampling of
all listenable stations on the frequency band. Press
the control again to stop the scan mode.
Scan function in tape mode
Press the SCAN control to hear a short sampling of
all selections on the tape. (The tape scans in a
forward direction. At the end of the tape's first side,
direction automatically reverses to the opposite side
of the tape.) To stop on a particular selection, press
the control again.
Scan function in CD mode
Press the SCAN control to hear a short sampling of
all selections on the CD. (The CD scans in a forward
SCAN
Controls and features
36

direction, wrapping back to the first track at the end
of the CD.) To stop on a particular selection, press
the control again.
Radio station memory preset
The radio is equipped with six station memory
preset controls. These controls can be used to select
up to six preset AM stations and twelve FM stations
(six in FM1 and six in FM2).
Setting memory preset stations
1. Select the frequency
band with the AM/FM
select control.
2. Select a station.
Refer toTune adjust
orSeek functionfor
more information on selecting a station.
3. Press and hold a memory preset control until the
sound returns, indicating the station is held in
memory on the control you selected.
Bass/treble adjust
²The bass adjust
control allows you to
increase or decrease
the audio system's
bass output.
AM
FM
VOL
PUSH-ON
REWSIDE 1-2COMPSHUFFLE123456
FF
BASSTREB
BAL
FADE
Controls and features
37

radio or CD mode, press the TAPE control. Press
the button during rewind or fast forward to stop
the rewind or fast forward function.
²To begin CD play (if CDs are loaded in the CD
changer), press the CD button. The first track of
the first disc will begin playing. After that CD play
will begin where it stopped last.
Rewind
The rewind control
works in tape and CD
modes.
²In tape mode, radio play will continue until
rewind is stopped (with the TAPE control) or the
beginning of the tape is reached.
²In CD mode, pressing the REW control for less
than three seconds results in slow rewind.
Pressing the control for more than three seconds
results in fast rewind.
Fast forward
The fast forward
control works in tape
and CD modes.
²In the tape mode,
tape direction will
automatically reverse
when the end of the
tape is reached.
²In CD mode, pressing the control for less than
three seconds results in slow forward action.
Pressing the control for more than three seconds
results in fast forward action.
Tape direction select
Press SIDE 1±2 to play
the alternate side of a
tape.
REW
5
FF
6
4SIDE 1-2
Controls and features
39