1999 DODGE RAM display

VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Clear trouble codes as needed. See BODY CONTROL COMPUTER -
INTRODUCTION article. Using scan tool, read I/O's door unlock switch
status. If scan tool displays RELEASED, system is currently
functioning properly. If scan tool does not display RELEASED, go to
next step.
2) Disconnect left door lock switch connector. If scan tool
displays RELEASED, replace left door lock switch. If scan tool does
not display RELEASED, go to next step.
3) Disconnect right door lock switch connector. If scan tool
displays RELEASED, replace right door lock switch. If scan tool does
not display RELEASED, go to next step.
4) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Disconnect CTM 18-pin connector C2.
Using an external voltmeter, measure voltage between ground and CTM
18-pin connector C2 terminal No. 4 (Orange/Dark Green wire). If
voltage is more than 1.5 volts, repair short to voltage in Orange/Dark
Green wire between CTM and door lock switch. If voltage is 1.5 volts
or less, replace CTM.
IDENTIFYING VTSS PROBLEMS
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool, select BODY SYSTEM then VTSS and read
Central Timer Module (CTM) DTCs. If any VTSS DTCs are displayed,
perform appropriate procedure. See VTSS DTC table. If no VTSS DTCs are
displayed, go to next step.
VTSS DTC









\









\









\









\









\









\









\








DTC Message Perform
DOOR DISARM SWITCH FAILURE .............. DOOR DISARM SWITCH FAILURE
DOOR LOCK SWITCH FAILURE .................. DOOR LOCK SWITCH FAILURE
DOOR UNLOCK SWITCH FAILURE .............. DOOR UNLOCK SWITCH FAILURE
EEPROM CHECKSUM FAILURE ................................ Replace CTM
INTERNAL ROM TEST FAILURE .............................. Replace CTM









\









\









\









\









\









\









\








2) Select VTSS then MONITORS. If scan tool displays, OK TO
RUN, NOT OK TO ARM, PCM has not recorded more than 20 starts. Start
engine 20 times and retest. If message does not change to OK TO ARM,
replace PCM. If scan tool displays NO RESPONSE TO PCM, see appropriate
VEHICLE COMMUNICATIONS article. If scan tool does not display OK TO
RUN, NOT OK TO ARM or NO RESPONSE TO PCM, go to next step.
3) Using scan tool, actuate horn, headlights and VTSS light
to flash. If horn does not sound, go to next step. If headlights do
not flash, go to step 6). If VTSS light does not flash, go to step 9).\
If all function properly, go to step 12).
4) Press horn button. If horn does not sound, go to
appropriate STEERING COLUMN SWITCHES article. If horn sounds, go to
next step.
5) Locate Central Timer Module (CTM). CTM is located behind

right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external voltmeter, measure voltage between ground and
CTM 18-pin connector C2 terminal No. 18 (Black/Red wire). If voltage
is more than 9.5 volts, replace CTM. If voltage is 9.5 volts or less,
repair open in Black/Red wire between CTM and horn relay.
6) Remove security relay from Power Distribution Center
(PDC). Turn ignition on. Connect a test light between battery source
and headlight relay connector terminal No. 85 (Red/Dark Blue wire).
Using scan tool, actuate relay. If test light illuminates, replace
security relay. If test light does not illuminate, go to next step.
7) Using an external voltmeter, measure voltage between
battery voltage and security relay connector terminal No. 86
(Red/Orange wire). If voltage is more than 9.5 volts, go to next step.\
If voltage is 9.5 volts or less, repair open in Red/Orange wire
between battery source and security relay.
8) Reinstall security relay. Locate Central Timer Module
(CTM). CTM is located behind right kick panel. Disconnect CTM 18-pin
connector C2. Using an external voltmeter, measure voltage between
ground and CTM 18-pin connector C2 terminal No. 6 (Red/Dark Blue
wire). If voltage is more than 9.5 volts, replace CTM. If voltage is
9.5 volts or less, repair open in Red/Dark Blue wire between CTM and
security relay.
9) Disconnect overhead console 12-pin connector. Using an
external voltmeter, measure voltage between battery and overhead
console 12-pin connector terminal No. 11 (Black wire). Using scan
tool, actuate VTSS indicator light. If voltage is about 10 volts,
replace overhead console. If voltage is not about 10 volts, go to next
step.
10) Measure voltage between ground and overhead console 12-
pin connector terminal No. 5 (Pink wire). Turn ignition on. If voltage\
is more than 10 volts, go to next step. If voltage is 10 volts or
less, repair open Pink wire.
11) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external ohmmeter, measure resistance between ground and
CTM 18-pin connector C2 terminal No. 8 (Black wire). If resistance is
5 ohms or more, replace CTM. If resistance is less than 5 ohms, repair
open Black wire between CTM and VTSS indicator light.
12) Using scan tool, place VTSS in diagnostic mode and follow
directions on screen. If TURN KEY TO ACC POSITION is not displayed, go
to step 24). If NO RESPONSE after turning key to accessory position or
TURN KEY TO ACC POSITION is displayed longer than 15 seconds, go to
next step. If neither response is received, go to step 14).
13) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Gain access to CTM 18-pin connector C2. Ensure key
is in accessory position. Using an external voltmeter, measure voltage
between ground and backprobe of CTM 18-pin connector C2 terminal No. 5
(Dark Blue/White wire). If voltage is more than 10 volts, replace CTM.\
If voltage is 10 volts or less, repair open Dark Blue/White wire
between CTM and junction block.
14) Remove key from ignition. Wait 2 seconds after performing
each of the following actions. Open, then close both door. Operate
power door lock switch to lock, then unlock position. Rotate key both
directions in both doors. Ensure each operation is successful. If any
operation is unsuccessful, see VTSS SYMPTOM DIRECTORY table for repair
of failed operation. If all operations are successful, go to step 22).
VTSS SYMPTOM DIRECTORY









\









\









\









\









\









\









\








Problem Circuit Go To
Driver's Door Open Or Close ............................... Step 15)

Passenger's Door Open Or Close ............................ Step 16)
Driver's Door Lock Switch ................. ONE OR ALL DOORS FAILING
TO LOCK FROM ONE SWITCH
Passenger's Door Lock Switch .............. ONE OR ALL DOORS FAILING
TO LOCK FROM ONE SWITCH
Driver's Key Cylinder ..................................... Step 17)
Passenger's Key Cylinder .................................. Step 20)
Driver's Door Unlock Switch ............... ONE OR ALL DOORS FAILING
TO UNLOCK FROM ONE SWITCH
Passenger's Door Unlock Switch ............ ONE OR ALL DOORS FAILING
TO UNLOCK FROM ONE SWITCH









\









\









\









\









\









\









\








15) Ensure driver's door is closed. Using scan tool, read
VTSS inputs/outputs door ajar status. If scan tool displays DR DOOR
AJAR SWITCH: CLOSED, go to SHORTED LEFT DOOR AJAR CIRCUIT under DOOR
AJAR SYSTEM. If scan tool does not display DR DOOR AJAR SWITCH:
CLOSED, go to OPEN LEFT DOOR AJAR CIRCUIT under DOOR AJAR SYSTEM.
16) Ensure passenger's door is closed. Using scan tool, read
VTSS inputs/outputs door ajar status. If scan tool displays DR DOOR
AJAR SWITCH: CLOSED, go to SHORTED RIGHT DOOR AJAR CIRCUIT under DOOR
AJAR SYSTEM. If scan tool does not display DR DOOR AJAR SWITCH:
CLOSED, go to OPEN RIGHT DOOR AJAR CIRCUIT under DOOR AJAR SYSTEM.
17) Using scan tool, monitor door disarm switch state.
Disconnect left door disarm switch. Connect jumper wire between left
door disarm switch connector terminals. If scan tool displays door
disarm switch state CLOSED, replace left door disarm switch. If scan
tool does not display door disarm switch state CLOSED, go to next
step.
18) Disconnect jumper wire. Connect jumper wire between
ground and left door disarm switch connector Light Green/Orange wire.
If scan tool displays door disarm switch state CLOSED, go to next
step. If scan tool does not display door disarm switch state CLOSED,
repair open left door disarm switch ground circuit (Black/Light Green
wire).
19) Access Central Timer Module (CTM). CTM is located behind\
right kick panel. Remove connector cover. Do not disconnect connector.
Connect a jumper between ground and backprobe CTM 18-pin connector C2
terminal No. 10 (Light Green/Orange wire). If scan tool displays door
disarm switch state CLOSED, repair open left door disarm switch sense
circuit (Light Green/Orange wire). If scan tool does not display door
disarm switch state CLOSED, replace CTM.
20) Using scan tool, monitor door disarm switch state.
Disconnect right door disarm switch. Connect jumper wire between right
door disarm switch connector terminals. If scan tool displays door
disarm switch state CLOSED, replace right door disarm switch. If scan
tool does not display door disarm switch state CLOSED, go to next
step.
21) Disconnect jumper wire. Connect jumper wire between
ground and right door disarm switch connector Light Green/Orange wire.
If scan tool displays door disarm switch state CLOSED, go to next
step. If scan tool does not display door disarm switch state CLOSED,
repair open right door disarm switch ground circuit (Black/Light Green
wire).
22) Access Central Timer Module (CTM). CTM is located behind\
right kick panel. Remove connector cover. Do not disconnect connector.
Connect a jumper between ground and backprobe CTM 18-pin connector C2
terminal No. 10 (Light Green/Orange wire). If scan tool displays door
disarm switch state CLOSED, repair open right door disarm switch sense
circuit (Light Green/Orange wire). If scan tool does not display door

disarm switch state CLOSED, replace CTM.
23) Turn ignition switch to START position. If horn does not
sound, go to next step. If horn sounds, go to step 24).
24) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 14-pin connector C1. Using an
external voltmeter, measure voltage between ground and CTM 14-pin
connector C1 terminal No. 8 (Dark Blue/White wire). If voltage is more\
than 10 volts, replace CTM. If voltage is 10 volts or less, repair
open Dark Blue/White wire between CTM and RUN-ACC fuse in junction
block.
WINDSHIELD WIPER SYSTEM
WIPER PARK SWITCH FAILURE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
NOTE: It takes 8 seconds for wiper park switch failure DTC to set.
1) Using scan tool, clear DTCs. See appropriate SELF-
DIAGNOSTICS article. Operate wipers in low speed, then intermittent
mode. Reread DTCs. If WIPER PARK SWITCH FAILURE is displayed, go to
next step. If WIPER PARK SWITCH FAILURE is not displayed, system is
currently functioning properly.
2) Gain access to wiper motor connector. Using an external
voltmeter, measure voltage between ground and wiper motor terminal No.
2 (Dark Green wire). If voltage is more than 9 volts, go to next step.\
If voltage is 9 volts or less, replace wiper motor.
3) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). If voltage is 9 volts or less,
replace CTM. If voltage is more than 9 volts, repair short to voltage
in Dark Green wire between CTM and wiper relay or wiper motor.
INTERMITTENT WIPERS INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select CENTRAL TIMER MODULE. If scan tool
displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) If problem is wipers parking in wrong position, go to next
step. If problem is not wipers parking in wrong position, go to step
5).
3) Gain access to wiper motor connector. Turn wipers on to
low speed. Using an external voltmeter, measure voltage between ground
and wiper motor switch terminal No. 2 (Dark Green wire). If voltage
does not cycle between zero and 12 volts, replace wiper motor. If
voltage cycles between zero and 12 volts, go to next step.

4) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). Wipers should be operating at low
speed. If voltage does not cycle between zero and 12 volts, repair
open Dark Green wire between CTM and wiper relay or wiper motor. If
voltage cycles between zero and 10 volts, replace CTM.
5) Using scan tool, monitor intermittent wiper voltage level.
Rotate wiper switch from low intermittent to high intermittent level.
If voltage changes from approximately 2.5 to 12 volts, replace CTM. If
voltage does not change from approximately 2.5 to 12 volts, go to next
step.
6) Disconnect 24-pin multifunction switch connector. Using an
external ohmmeter, measure resistance of White/Dark Blue wire between
multifunction switch connector terminal No. 1 and CTM 14-pin Green
connector C1 terminal No. 12. if resistance is less than 5 ohms,
replace multifunction switch. If resistance is 5 ohms or more, repair
open White/Dark Blue wire between multifunction switch and CTM.
NO WIPER ACTUATION AFTER WASH BUTTON PUSHED
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central Timer Module (CTM). If sca\
n
tool displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) Turn ignition on. If washer system works, go to next step.
If washer system does not work, see appropriate WIPER/WASHER SYSTEMS
article.
3) Using scan tool, actuate washer. If washer pump sense
displays ON, replace CTM. If washer pump sense does not display ON,
repair open Brown wire between CTM 14-pin connector C1 terminal No. 10
and multifunction switch.
WIPER SPEED SENSITIVE FEATURE INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select Central timer module (CTM). If sca\
n
tool display is not blank or have a CCD bus failure message, go to
next step. If scan tool display is blank or has a CCD bus failure
message, see appropriate VEHICLE COMMUNICATIONS article.
2) Using scan tool, select Powertrain Control Module (PCM).
If scan tool display is not blank or have a CCD bus failure message,
go to next step. If scan tool display is blank or has a CCD bus
failure message, see appropriate VEHICLE COMMUNICATIONS article.
3) Raise and support vehicle. Turn wipers on to lowest
intermittent position. Time interval between wipes. Spin rear wheels
to more than 15 MPH. If interval between wipes decreased to
approximately 18 seconds, system is currently functioning properly. If
interval between wipes did not decrease to approximately 18 seconds,

DTCs from ABS and SRS modules.
Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC) below driver's\
side of instrument panel. Go to ENGINE, then MISC menu on scan tool.
Place the SKIM in SECURED ACCESS MODE by using the appropriate
Personal Identification Number (PIN) for this vehicle. PIN may be
obtained from the owner, vehicle's invoice, or from the manufacturer.
Select UPDATE THE SECRET KEY DATA. The data will be transferred from
Smart Key Immobilizer Module (SKIM) to the PCM.
NOTE: If 3 attempts are made to enter the SECURED ACCESS MODE using
the incorrect Personal Identification Number (PIN), the
SECURED ACCESS MODE will be locked out for one hour. To exit
this locked-out mode, leave ignition switch in the ON
position for one hour with all accessories turned off. It may
be necessary to monitor battery state and connect a battery
charger.
FWD CARS & FWD VANS
Transaxle Shift Quality Quick Learn Procedure (All FWD Cars
Except Avenger & Sebring Coupe, & All FWD Vans)
1) Transaxle shift quality quick learn procedure must be
performed to provide proper transaxle operation if any of the
following have been done:
* Vehicle battery was disconnected.
* Transaxle assembly was replaced.
* Transmission Control Module (TCM) was replaced.
* Solenoid assembly was replaced.
* Valve body was reconditioned or replaced.
2) Transaxle shift quality quick learn procedure must be
performed using Chrysler's Diagnostic Readout Box III (DRB-III) scan
tool. Following conditions must be met when performing transaxle shift
quality quick learn procedure:
* Brakes must be applied.
* Engine speed must be greater than 500 RPM.
* Throttle position sensor angle must be less than 3 degrees.
* Shift lever must remain in designated position until prompted
to shift to overdrive.
* Shift lever must remain in overdrive after the shift to
overdrive until scan tool indicates procedure is complete.
* Calculated oil temperature must be within 60-200
F
(16-93C).
3) Connect scan tool to Data Link Connector (DLC) below
driver's side of instrument panel. For DLC location, see appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
4) Go to TRANSMISSION display on scan tool. Go to
MISCELLANEOUS display on scan tool. Select QUICK LEARN PROCEDURE
display on scan tool. Follow instructions displayed on scan tool to
perform transaxle shift quality quick learn procedure. Remove scan
tool.
Transaxle Shift Quality Quick Learn Procedure (Avenger &
Sebring Coupe)
1) Transaxle shift quality quick learn procedure must be
performed to provide proper transaxle operation after replacing or
overhauling transaxle. After transaxle work is completed, clear any
Diagnostic Trouble Codes (DTCs) as necessary. Connect Chrysler's

Diagnostic Readout Box III (DRB-III) scan tool to Data Link Connector
(DLC) below driver's side of instrument panel. For DLC location, see
appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
2) Select SPECIAL FUNCTION on scan tool. Set scan tool to
QUICK LEARN mode. Follow scan tool manufacturer's instructions to
perform transaxle shift quality quick learn procedure. Remove scan
tool.
Pinion Factor Procedure (All FWD Cars Except Avenger &
Sebring Coupe, & All FWD Vans)
1) Electronic pinion factor procedure must be performed to
provide proper speedometer operation if Transmission Control Module
(TCM) is replaced. If pinion factor procedure is not performed,
improper speedometer readings may exist or speedometer may not
operate. Pinion factor procedure must be performed using Chrysler's
Diagnostic Readout Box (DRB-III) scan tool.
2) Connect scan tool to Data Link Connector (DLC) below
driver's side of instrument panel. For DLC location, see appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
3) Select TRANSMISSION system, MISCELLANEOUS functions, then
PINION FACTOR. Scan tool will now display tire size. If tire size is
incorrect, press ENTER key and select correct size. Press PAGE BACK
key to exit procedure.
Pinion Factor Procedure (Avenger & Sebring Coupe)
1) Transaxle uses rotation speed of output shaft to calculate
vehicle speed and cumulative distance travelled. Therefore, it is
necessary to input or update tire size into TCM memory after TCM has
been replaced or tire size has been changed.
2) Select SPECIAL FUNCTION on Chrysler's Diagnostic Readout
Box (DRB-III) scan tool. Set scan tool to PINION FACTOR mode. Input
tire size into TCM memory.
NOTE: New TCMs do not have tire size input into memory. TCM may
also be referred to as EATX module.

made.
* When using a jumper wire, ensure either jumper wire or
circuit is fuse-protected.
* Before disconnecting connector from any control module,
ensure ignition is off before removing connector.
* When checking voltage or continuity at any control module,
probe connector for control module from pin side. DO NOT
backprobe connector or probe wires through insulation.
* DO NOT cause short circuits when performing electrical tests.
This will set additional Diagnostic Trouble Codes (DTCs),
making diagnosis of original problem more difficult.
* Use specified test equipment when performing electrical
tests.
RETRIEVING DIAGNOSTIC TROUBLE CODES
NOTE: Self-diagnostic tests are written specifically for Chrysler's
Diagnostic Readout Box (DRB). If using a generic scan tool,
ensure it is OBD-II certified. A generic scan tool may not be
capable of performing all necessary test functions.
Ensure battery is fully charged. Turn ignition off. Connect
scan tool to Data Link Connector (DLC). DLC is located under left side\
of instrument panel. Turn ignition on. Using scan tool manufacturer's
instructions, record all DTCs displayed on scan tool. If ant DTCs are
retrieved, perform appropriate test under DIAGNOSTIC TESTS. Once all
repairs are made, clear DTCs. See CLEARING DIAGNOSTIC TROUBLE CODES.
If no DTCs are retrieved and fault still exists, go to CHECKING SPEED
CONTROL OPERATION under SYSTEM TESTS.
CLEARING DIAGNOSTIC TROUBLE CODES
Ensure ignition is off. Connect scan tool to DLC. Turn
ignition on. Using screen prompts on scan tool, erase DTCs from PCM.
DIAGNOSTIC TESTS
FTC P0720: LOW OUTPUT SPEED SENSOR (OSS) RPM MORE THAN 15 MPH
FTC P0720 will set if output shaft speed is less than 60 RPM
for 2.6 seconds when vehicle speed is more than 15 MPH.
Possible Causes:
* Defective Output Speed Sensor (OSS).
* OSS signal circuit open or shorted.
* OSS ground circuit open or shorted.
* Park/Neutral Position (PNP) switch FTC present.
* Defective PNP switch.
* Defective PCM.
1) Turn ignition on. Using scan tool, read DTCs. If FTC
specific good trip is displayed and equal to zero, go to next step. If
FTC specific good trip is equal to more than zero, go to step 13).
2) If there are any Park/Neutral Position (PNP) switch DTCs,\
repair PNP switch FTC first. Perform TEST VER-5A under VERIFICATION
TESTS. If there are no PNP switch DTCs, go to next step.
3) Using scan tool, read PNP switch state. While observing
scan tool, shift transmission through all positions. If scan tool did
not display P/N and D/R in correct positions, repair PNP switch or
circuit as necessary. Perform TEST VER-5A under VERIFICATION TESTS. If