1999 DODGE RAM lock

NOTE: Fuel level sensor may also be referred to as fuel gauge
sending unit.
Removal
1) Fuel level sensor is mounted on fuel pump module. See
Fig. 31 . Fuel pump module is located on top of fuel tank. See Figs. 27
-30.
2) Remove fuel pump module. See FUEL PUMP MODULE under FUEL
SYSTEM. Disconnect electrical connector for fuel pump and fuel level
sensor from electrical connector from bottom side of electrical
connector mounted on top of fuel pump module. See Fig. 31.
3) Remove locking collar from electrical connector for fuel
pump and fuel level sensor. Locking collar must be removed so wires
for fuel level sensor may be removed from the electrical connector for
fuel pump and fuel level sensor.
CAUTION: Note location of wires in electrical connector for fuel pump
and fuel level sensor for installation reference. Wires must
be installed in correct location.
4) Mark wire location in electrical connector for fuel pump
and fuel level sensor for installation reference. Remove wires for
fuel level sensor from electrical connector for fuel pump and fuel
level sensor.
5) Note location of notch and locking tab at end of fuel
level sensor. See Fig. 31. Carefully push locking tab away from notch
while sliding fuel level sensor down the channels, toward bottom of
fuel pump module. Note wire routing when removing fuel level sensor
from fuel pump module. Remove fuel level sensor.
Installation
1) Install fuel level sensor on channels of fuel pump module.
Ensure wires are properly routed. Slide fuel level sensor onto fuel
pump module until fuel level sensor snaps into place. Ensure locking
tab is fully seated.
2) Install wires for fuel level sensor in electrical
connector for fuel pump and fuel level sensor. Install locking collar.
Install electrical connector for fuel pump and fuel level sensor on
electrical connector on bottom side of electrical connector mounted on
top of fuel pump module. Reinstall fuel pump module. To complete
installation, reverse removal procedure.
Fig. 31: Locating Fuel Level Sensor, Fuel Pump & Fuel Pump Inlet
Strainer On Typical Fuel Pump Module
Courtesy of Chrysler Corp.
FUEL PRESSURE REGULATOR

Removal & Installation
Fuel pressure regulator is incorporated with the fuel filter.
For servicing for fuel filter/fuel pressure regulator, see FUEL
FILTER/FUEL PRESSURE REGULATOR.
FUEL PUMP
Removal & Installation
Fuel pump is incorporated into the fuel pump module. See FUEL
PUMP MODULE.
FUEL PUMP INLET STRAINER
Removal & Installation
1) Fuel pump inlet strainer is mounted on fuel pump module.
See Fig. 31 . Remove fuel pump module. See FUEL PUMP MODULE.
2) Spread locking tabs on bottom of fuel pump module and
remove fuel pump inlet strainer from fuel pump module. See Fig. 31.
Remove "O" ring from end of fuel pump module if "O" ring was not
removed with fuel pump inlet strainer.
3) To install, reverse removal procedure. Ensure "O" ring is
properly seated when installing fuel pump inlet strainer. Reinstall
fuel pump module using proper procedure.
FUEL PUMP MODULE
Removal (Dakota)
1) Fuel pump module is located on top of fuel tank. See
Fig. 27 . Fuel tank must be removed for servicing of fuel pump module.
Remove fuel tank. See FUEL TANK.
2) Ensure area around fuel pump module is clean. Using Fuel
Pump Module Lock Nut Spanner Wrench (6856), remove fuel pump module
lock nut. See Fig. 32. Remove fuel pump module with rubber gasket from
fuel tank.
CAUTION: When fuel pump module is removed from fuel tank, rubber
gasket must be replaced. DO NOT reuse rubber gasket.
Installation
1) Ensure sealing area on fuel tank is clean. Using NEW
rubber gasket, install fuel pump module on fuel tank. DO NOT reuse
rubber gasket. Ensure rubber gasket remains in place.
NOTE: Fuel pump module must be properly positioned in fuel tank to
prevent float from contacting the fuel tank.
2) Rotate fuel pump module so alignment arrow on fuel pump
module is at 7 o'clock position and aligns with reference mark on fuel
tank. See Fig. 33. Install and hand tighten fuel pump module lock nut.
3) Note location of fuel pressure regulator on fuel pump
module. See Fig. 27. Ensure fuel filter/pressure regulator is
positioned on fuel pump module so fuel line fitting on side fuel
filter/fuel pressure regulator points toward driver's side of vehicle.
4) Hold fuel pump module in place while tightening fuel pump
module lock nut to specification. See TORQUE SPECIFICATIONS. Reinstall
fuel tank using proper procedure.

Fig. 32: Removing & Installing Typical Fuel Pump Module Lock Nut
(Dakota, Ram Pickup, Ram Van & Ram Wagon)
Courtesy of Chrysler Corp.
Fig. 33: Positioning Fuel Pump Module In Fuel Tank (Dakota)
Courtesy of Chrysler Corp.
Removal (Durango)
1) Fuel pump module is located on top of fuel tank. See

Fig. 28. Fuel tank must be removed for servicing of fuel pump module.
Remove fuel tank. See FUEL TANK under FUEL SYSTEM.
2) Ensure area around fuel pump module is clean. Rotate fuel
filter/pressure regulator so fuel line fitting on side fuel
filter/fuel pressure regulator points toward center of fuel pump
module.
3) Note location of metal fuel pump module lock ring and
locking fingers on the fuel tank. See Fig. 34. There are 6 locking
fingers molded into the plastic fuel tank.
4) Apply a small amount of engine oil on each locking finger
at the fuel pump module lock ring area. Engine oil will act as a
lubricant when removing fuel pump module lock ring.
5) Note location of lock tab on fuel pump module lock ring.
Pry lock tab backward while using a hammer and brass drift to tap fuel
pump module lock ring counterclockwise. Remove fuel pump module lock
ring, fuel pump module and rubber gasket from fuel tank.
CAUTION: When fuel pump module is removed from fuel tank, rubber
gasket must be replaced. DO NOT reuse rubber gasket.
Installation
1) Ensure sealing area on fuel tank is clean. Using NEW
rubber gasket, install fuel pump module on fuel tank. DO NOT reuse
rubber gasket. Ensure rubber gasket remains in place.
NOTE: Fuel pump module must be properly positioned in fuel tank to
prevent float from contacting the fuel tank.
2) Rotate fuel pump module so fuel pump is properly
positioned in the fuel tank. See Fig. 34. Apply a small amount of
engine oil on each locking finger at fuel pump module lock ring area.
Install fuel pump lock ring on fuel pump module.
3) Using a hammer and brass drift, tap fuel pump module lock
ring clockwise until the 6 locking fingers engage in fuel pump module
lock ring and lock tab engages notch on fuel pump module lock ring.
Ensure lock tab fully engages with notch on fuel pump module lock
ring. Reinstall fuel tank using proper procedure.
Fig. 34: Locating Fuel Pump Module Lock Ring, Locking Fingers &
Positioning Fuel Pump Module In Fuel Tank (Durango)
Courtesy of Chrysler Corp.
Removal (Ram Pickup)

1) Fuel pump module is located on top of fuel tank. See
Fig. 29. Fuel tank must be removed for servicing of fuel pump module.
Remove fuel tank. See FUEL TANK under FUEL SYSTEM.
2) Ensure area around fuel pump module is clean. Note
position of fuel pump module installation in fuel tank for
installation reference. Using Fuel Pump Module Lock Nut Spanner Wrench
(6856), remove fuel pump module lock nut. See Fig. 32. Remove fuel
pump module with rubber gasket from fuel tank.
CAUTION: When fuel pump module is removed from fuel tank, rubber
gasket must be replaced. DO NOT reuse rubber gasket.
Installation
1) Ensure sealing area on fuel tank is clean. Using NEW
rubber gasket, install fuel pump module on fuel tank. DO NOT reuse
rubber gasket. Ensure rubber gasket remains in place.
NOTE: Fuel pump module must be properly positioned in fuel tank to
prevent float from contacting the fuel tank.
2) Loosely install fuel pump module lock nut. Rotate fuel
pump module so electrical connector is pointing toward driver's side
of fuel tank. See Fig. 29.
3) Note location of fuel pressure regulator on fuel pump
module. See Fig. 29. Ensure fuel filter/pressure regulator is
positioned on fuel pump module so fuel line fitting on side fuel
filter/fuel pressure regulator points toward driver's side of fuel
tank.
4) Hold fuel pump module in place while tightening fuel pump
module lock nut to specification. See TORQUE SPECIFICATIONS. Reinstall
fuel tank using proper procedure.
Removal (Ram Van & Ram Wagon)
1) Fuel pump module is located on top of fuel tank. See
Fig. 30 . Fuel tank must be removed for servicing of fuel pump module.
Remove fuel tank. See FUEL TANK.
2) Ensure area around fuel pump module is clean. Using Fuel
Pump Module Lock Nut Spanner Wrench (6856), remove fuel pump module
lock nut. See Fig. 32. Remove fuel pump module with rubber gasket from
fuel tank.
CAUTION: When fuel pump module is removed from fuel tank, rubber
gasket must be replaced. DO NOT reuse rubber gasket.
Installation
1) Ensure sealing area on fuel tank is clean. Using NEW
rubber gasket, install fuel pump module on fuel tank. DO NOT reuse
rubber gasket. Ensure rubber gasket remains in place.
NOTE: Fuel pump module must be properly positioned in fuel tank to
prevent float from contacting the fuel tank.
2) Rotate fuel pump module so alignment mark on fuel pump
module aligns with reference mark on fuel tank. See Fig. 35. Install
and hand tighten fuel pump module lock nut.
3) Note location of fuel pressure regulator on fuel pump
module. See Fig. 35. Ensure fuel filter/pressure regulator is
positioned on fuel pump module so fuel line fitting on side fuel
filter/fuel pressure regulator points toward driver's side of vehicle.
4) Hold fuel pump module in place while tightening fuel pump
module lock nut to specification. See TORQUE SPECIFICATIONS. Reinstall
fuel tank using proper procedure.

1) To install, reverse removal procedure. If installing small
vent tube and large fill tube on fuel tank, ensure fuel tank fittings
are clean.
2) Install disconnect fitting on fuel tank fitting until
disconnect fitting snaps onto fuel tank fitting. Pull on small vent
tube or and large fill tube to ensure disconnect fitting is locked on
fuel tank fitting. To verify proper installation of disconnect
fitting, ensure the distance between release sleeve and top of fuel
tank fitting is .50" (12.7 mm) on small vent tube or .25" (6.4 mm) o\
n
large fill tube. See Fig. 37.
3) Install fuel lines on fuel filter/fuel pressure regulator
on fuel pump module using proper procedure. See FUEL LINE DISCONNECT
FITTINGS under FUEL SYSTEM.
CAUTION: DO NOT overtighten fuel tank strap retaining nuts during
installation.
4) Tighten fuel tank strap retaining nuts to specification.
See TORQUE SPECIFICATIONS. To install remaining components, reverse
removal procedure. Start engine and check for fuel leaks.
Removal (Durango)
1) Fuel tank may be drained by removing vent hose from rear
of fuel tank, or by pumping fuel from fuel tank using the fuel pump if
fuel pump is operating. If removing vent hose from fuel tank to drain
the fuel, go to step 4). If using fuel pump to drain the fuel tank, go
to next step.
2) Disconnect fuel line from fuel rail. See FUEL LINE AT FUEL
RAIL under FUEL SYSTEM. Connect Fuel Hose (6541, 6539, 6631 or 6923)
for proper engine application at fuel line fitting on fuel rail. Place
remaining end of fuel hose in an approved gasoline container.
3) Connect scan tool to Data Link Connector (DLC). DLC is a
16-pin connector attached to bottom of driver's side of the instrument
panel, just to the right of the brake pedal. Using scan tool
manufacturer's instructions, activate the fuel pump and pump fuel from
fuel tank. Once fuel tank is empty, remove scan tool. Reinstall fuel
line on fuel rail using proper procedure. Go to step 5).
4) Release fuel pressure from fuel system. See FUEL SYSTEM
PRESSURE RELEASE. Ensure negative battery cable is disconnected.
Remove fuel tank cap to release any residual fuel tank pressure.
5) Raise and support vehicle. Remove necessary skid plates
for access to fuel tank. Disconnect vent and filler hose from rear of
fuel tank. If fuel tank was not previously drained, place drain hose
in vent hose fitting at rear of fuel tank. Drain fuel from fuel tank
into an approved gasoline container.
6) Support fuel tank with transmission jack. Remove fuel tank
strap retaining nuts. Position fuel tank straps toward outside of
vehicle. Slightly lower fuel tank. Ensure rear of fuel tank is higher
than front of fuel tank to prevent any spilling any remaining fuel in
fuel tank.
7) Disconnect fuel line from fuel filter/fuel pressure
regulator on fuel pump module using proper procedure for fuel line
disconnect fitting. See FUEL LINE DISCONNECT FITTINGS. Fuel pump
module is located on top of fuel tank. See Fig. 28. Disconnect
electrical connector at fuel pump module. Disconnect vapor line from
rollover valves on top of fuel tank and EVAP line from fuel pump
module. Lower fuel tank from vehicle.
CAUTION: DO NOT overtighten fuel tank strap retaining nuts during
installation.
Installation
1) To install, reverse removal procedure. Install fuel lines

\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Crankshaft Position Sensor Bolt
2.5L ..................................................... 14 (19)\
3.9L, 5.2L & 5.9L ............................................ (1)
8.0L ......................................................... ( 1)
Downstream Oxygen Sensor ................................... 22 (30)\
Distributor Hold-Down Bolt ................................. 17 (23)\
EVAP Canister-To-Mounting Bracket Nut
Dakota & Durango ......................................... 17 (23)\
Ram Pickup ................................................... ( 2)
Ram Van & Ram Wagon .......................................... ( 3)
Fuel Pump Module Lock Nut
Dakota ................................................... 40 (54)\
Ram Pickup ............................................... 32 (43)\
Ram Van & Ram Wagon ...................................... 40 (54)\
Fuel Rail Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
8.0L ..................................................... 11 (15)\
Fuel Tank Strap Nut
Dakota & Durango ......................................... 40 (54)\
Ram Pickup ............................................... 30 (41)\
Ram Van & Ram Wagon .......................................... ( 5)
IAT Sensor ................................................. 20 (27)\
Park/Neutral Switch ........................................ 25 (34)\
Power Steering Pressure Switch (2.5L) ...................... 16 (22\
)
Spark Plug ................................................. 30 (41)\
Throttle Body Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
Throttle Body Nut (8.0L) ................................... 16 (22\
)
Upper Intake Manifold Bolt (8.0L) ...................... ( 6) 16 (22)
Upstream Oxygen Sensor ..................................... 22 (30)\
Wheel Lug Nut (Dakota & Durango) ......................... 100 (136\
)
INCH Lbs. (N.m)
Air Cleaner Housing-To-Throttle
Body Nut (Dakota & Durango) ............................. 96 (10.8\
)
Camshaft Position Sensor Bolt (8.0L) ...................... 50 (5.6\
)
Engine Coolant Temperature Sensor ........................ 96 (10.8)\
EVAP Canister Mounting Bracket-To
Body Nut (Ram Van & Ram Wagon) .......................... 95 (10.7\
)
EVAP Leak Detection Pump Filter
Bolt (Ram Pickup, Ram Van & Ram Wagon) ................... 65 (7.3\
)
EVAP Leak Detection Pump Bolt ............................. 11 (1.2)\
EVAP Purge Solenoid Nut (Dakota & Durango) ................ 75 (8.5\
)
IAC Motor Bolt ............................................ 60 (6.8)\
Ignition Coil Bolt/Nut
Dakota, Durango, Ram Van & Ram Wagon ......................... ( 7)
Ram Pickup
3.9L, 5.2L & 5.9L ........................................... ( 7)
8.0L .................................................. 90 (10.2)\
MAP Sensor Bolt
Dakota & Durango ........................................ 25 (2.8)\
Ram Pickup
3.9L, 5.2L & 5.9L ...................................... 25 (2.8)\
8.0L ................................................... 20 (2.3)\
Ram Van & Ram Wagon ..................................... 25 (2.8)\
PCM Bolt .................................................. 35 (4.0)\
TP Sensor Bolt ............................................ 60 (6.8)\

 Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


12,000 MILE (19,000 KM)/12 MONTH NORMAL SERVICE
12,000 MILE (19,000 KM)/12 NORMAL SERVICE
\
\
\
\
\
\
\
 
INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Water Pump Weep Hole For Blockage 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 


\
\
\
\
\
\
\


 Clean Fuel Strainer 

\
\
\
\
\
\
\



REPLACE