1999 DODGE RAM ignition switch output PCM

voltage. If voltage is less than one volt, go to next step. If voltage
is one volt or more, condition to set FTC is not present at this time.
Test is complete.
2) While observing scan tool, disconnect S/C ON/OFF switch.
If S/C switch voltage changes to 5 volts, replace S/C ON/OFF switch.
Perform TEST VER-4A under VERIFICATION TESTS. If voltage does not
change to 5 volts, go to next step.
3) While observing scan tool, disconnect S/C RESUME/ACCEL
switch. If S/C switch voltage changes to 5 volts, replace S/C
RESUME/ACCEL switch. Perform TEST VER-4A under VERIFICATION TESTS. If
voltage does not change to 5 volts, go to next step.
4) Turn ignition off. Ensure both S/C switches are still
disconnected. Using an ohmmeter, check resistance between S/C switch
connector terminals (S/C switch signal circuit and S/C switch ground
circuit). If resistance is less than 5 ohms, repair short circuit.
Perform TEST VER- 4A under VERIFICATION TESTS. If resistance is 5 ohms
or more, go to next step.
5) Disconnect clockspring 4-pin connector. Clockspring 4-pin
connector is located behind steering wheel. Inspect connector. Clean
or repair as necessary. Using an ohmmeter, check resistance between
ground and S/C switch signal circuit at clockspring connector (Dark
Green/Red wire on all models except Ram Van and Ram Wagon; wire color
is not available for Ram Van and Ram Wagon). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
6) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance between ground and S/C
switch signal circuit at either S/C switch connector (Dark Green/Red
wire on all models except Ram Van and Ram Wagon; wire color is not
available for Ram Van and Ram Wagon). If resistance is less than 5
ohms, repair short to ground. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-
4A under VERIFICATION TESTS.
FTC P1683: SPEED CONTROL POWER RELAY CIRCUIT
FTC P1683 will set if Speed Control (S/C) power supply
circuit is open or shorted when S/C is turned on.
Possible Causes:
* Brake switch out of adjustment.
* S/C brake switch output circuit open or shorted.
* Defective S/C servo.
* Defective brake switch.
* S/C vacuum or vent solenoid control circuits open or
shorted.
* Defective PCM.
* Ground circuit open.
* S/C power supply circuit open.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
1) Turn ignition off. Disconnect S/C servo connector. Inspect
connector. Clean or repair as necessary. Turn ignition on. Using scan
tool, actuate S/C relay. Using a 12-volt test light, probe S/C brake
switch output circuit at S/C servo connector terminal No. 3 (Dark
Blue/Red wire). If test light is illuminated and bright, go to next

step. If test light is dim or not illuminated, go to step 7).
2) Turn ignition off. Using an ohmmeter, check resistance of
ground circuit at S/C servo connector terminal No. 4 (Black wire). If
resistance is 5 ohms or more, repair open ground circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
3) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, measure resistance of S/C vacuum
solenoid control circuit between PCM connector C3, terminal No. 4 and
S/C servo connector terminal No. 1 (Tan/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
4) Using an ohmmeter, check resistance between ground and S/C
vacuum solenoid control circuit at S/C servo connector terminal No. 1
(Tan/Red wire). If resistance is less than 5 ohms, repair short to
ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance is
5 ohms or more, go to next step.
5) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between PCM connector C3, terminal No. 5 and S/C servo
connector terminal No. 2 (Light Green/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
6) Using an ohmmeter, check resistance between ground and S/C
vent solenoid control circuit at S/C servo connector terminal No. 2
(Light Green/Red wire). If resistance is less than 5 ohms, repair
short to ground. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is 5 ohms or more, replace S/C servo. Perform TEST VER-4A
under VERIFICATION TESTS.
7) Turn ignition off. Disconnect brake switch connector.
Inspect connectors. Clean or repair as necessary. Turn ignition on.
Using scan tool, actuate S/C solenoid. Using a 12-volt test light,
probe S/C power supply circuit at brake switch connector terminal No.
4 (Yellow/Red wire). If test light is illuminated and bright, go to
next step. If test light is not illuminated or dim, go to step 10).
8) Check brake switch adjustment. See BRAKE SWITCH under
REMOVAL & INSTALLATION. Adjust as necessary. Perform TEST VER- 4A
under VERIFICATION TESTS. If brake switch adjustment is okay, go to
next step.
9) Using an ohmmeter, check resistance of brake switch output
circuit between brake switch connector terminal No. 3 and S/C servo
connector terminal No. 3 (Dark Blue/Red wire). If resistance is more
than 5 ohms, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or less, replace brake
switch. Perform TEST VER-4A under VERIFICATION TESTS.
10) Turn ignition off. Using an ohmmeter, check resistance
between ground and S/C brake switch output circuit at S/C servo
connector terminal No. 3 (Dark Blue/Red wire). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
11) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance of S/C power supply
circuit between PCM connector C3, terminal No. 11 and brake switch
connector terminal No. 4 (Yellow/Red wire). If resistance is 5 ohms or\
more, repair open circuit. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is less than 5 ohms, replace PCM. Perform TEST
VER-4A under VERIFICATION TESTS.
FTC P1899: PARK/NEUTRAL POSITION (PNP) SWITCH STUCK IN PARK
OR IN GEAR (A/T MODELS)
Possible Causes:

next step. If scan tool does not display brake pedal PRESSED and
RELEASED, go to NTC-1: BRAKE SWITCH SENSE.
4) Turn S/C on. On A/T models, move gear selector to Drive.
If scan tool displays park neutral switch D/R, go to next step. If
scan tool does not display park neutral switch D/R, go to FTC P1899:
PARK/NEUTRAL POSITION SWITCH STUCK IN PARK OR IN GEAR under DIAGNOSTIC
TESTS.
5) On all models, using scan tool, actuate S/C vent solenoid.
Using a 12-volt test light, backprobe S/C brake switch output circuit
at S/C servo connector terminal No. 3 (Dark Blue/Red wire). If test
light is illuminated and bright, go to next step. If test light is dim
or is not illuminated, go to NTC-1: BRAKE SWITCH SENSE.
6) Start engine and let idle for one minute. Turn engine off.
Turn ignition on (engine off). Using scan tool, actuate S/C servo
solenoids. If throttle opens and closes, go to NTC-2: CHECKING FOR
SPEED CONTROL DENIED MESSAGE. If throttle does not open and close,
inspect throttle cable and linkage. Check vacuum supply. See VACUUM
SUPPLY under COMPONENT TESTS. Repair as necessary. Perform TEST VER-4A
under VERIFICATION TESTS.
7) While observing scan tool, press CANCEL switch several
times. If scan tool displays PRESSED and RELEASED, go to next step. If
scan tool does not display PRESSED and RELEASED, replace CANCEL
switch. Perform TEST VER-4A under VERIFICATION TESTS.
8) Turn ignition off. Disconnect S/C servo connector. Using
an ohmmeter, check resistance of ground circuit at S/C servo connector
terminal No. 4 (Black wire). If resistance is 5 ohms or more, repair
open ground circuit. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is less than 5 ohms, go to next step.
9) Reconnect S/C servo connector. Turn ignition and S/C on.
While observing scan tool, press SET switch several times. If scan
tool displays PRESSED and RELEASED, go to next step. If scan tool does
not display PRESSED and RELEASED, replace SET switch. Perform TEST
VER-4A under VERIFICATION TESTS.
10) Turn ignition off. Disconnect S/C servo connector.
Inspect terminals. If any terminal is damaged, pushed out or miswired,
repair as necessary. Perform TEST VER-4A under VERIFICATION TESTS. If
terminals are okay, go to next step.
11) Disconnect S/C servo connector. Disconnect PCM
connectors. Inspect connectors. Clean or repair as necessary. Using an
ohmmeter, check resistance of S/C vacuum solenoid control circuit
between PCM connector C3, terminal No. 4 and S/C servo connector
terminal No. 1 (Tan/Red wire). If resistance is 5 ohms or more, repair\
open circuit. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is less than 5 ohms, go to next step.
12) Turn S/C on. While observing scan tool, press COAST
switch several times. If scan tool displays PRESSED and RELEASED, go
to next step. If scan tool does not display PRESSED and RELEASED,
replace COAST switch. Perform TEST VER-4A under VERIFICATION TESTS.
13) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between PCM connector C3, terminal No. 5 and S/C servo
connector terminal No. 2 (Light Green/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace S/C
servo. Perform TEST VER-4A under VERIFICATION TESTS.
NTC-1: BRAKE SWITCH SENSE
Possible Causes:
* Ground circuit open.
* Defective brake switch.
* Brake switch sense circuit open or shorted.
* Defective PCM.

1) Turn ignition off. Disconnect brake switch connector.
Inspect connector. Clean or repair as necessary. Turn ignition on.
Using a voltmeter, measure voltage of brake switch sense circuit at
brake switch White/Pink wire. If voltage is more than 10 volts, go to
next step. If voltage is 10 volts or less, go to step 3).
2) Connect a jumper wire between ground and brake switch
connector White/Pink wire. Using scan tool, read brake switch input
status. If scan tool displays brake switch released, replace brake
switch. Perform TEST VER-4A under VERIFICATION TESTS. If scan tool
does not display brake switch released, repair open ground circuit.
Perform TEST VER-4A under VERIFICATION TESTS.
3) Disconnect PCM connectors. Inspect connectors. Clean or
repair as necessary. Using an ohmmeter, measure resistance between
ground and brake switch sense circuit at PCM connector C3, terminal
No. 24 (White/Pink wire). If resistance less than 5 ohms, repair short\
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
4) Using an ohmmeter, measure resistance of brake switch
sense circuit between PCM connector C3, terminal No. 24 and brake
switch White/Pink wire. If resistance is 5 ohms or more, repair open
brake switch sense circuit. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is less than 5 ohms, replace PCM. Perform TEST
VER-4A under VERIFICATION TESTS.
NTC-2: CHECKING FOR SPEED CONTROL DENIED MESSAGE
At this time speed control switch and servo functions appear
to operate properly. Using scan tool, monitor speed control output
status. Road test vehicle at speeds more than 30 MPH. Attempt to set
speed control. See SCAN TOOL DENIED STATUS table. Items listed in
table will not allow speed control to set. The last or most recent
cause for speed control not to set is indicated by denied status.
Correct fault and recheck system operation.
SCAN TOOL DENIED STATUS








\









\









\









\









\









\









\






 
Denied Message Reason 










\





\b



\









\









\









\









\









\







ON/OFF  PCM Does Not See An ON Signal From Switch 

 At PCM Terminal No. 41 










\





\b



\









\









\









\









\









\







SPEED  Vehicle Speed As Seen By PCM Terminal 

 No. 66 Is Not Greater Than 36 MPH 










\





\b



\









\









\









\









\









\







RPM  Engine RPM Is Excessively High 










\





\b



\









\









\









\









\









\







BRAKE  Brake Switch Sense Circuit Is Open 

 Indicating That Brakes Are Applied 










\





\b



\









\









\









\









\









\







P/N  Park/Neutral Switch Sense Circuit Is Grounded 

 Indicating That Transmission Is In Park Or Neutral 










\





\b



\









\









\









\









\









\







RPM/SPD  PCM Senses Excessive Engine RPM 

 For A Given Vehicle Speed 










\





\b



\









\









\









\









\









\







SOL FLT  PCM Senses A Servo Solenoid Circuit 

 Trouble Code That Is Maturing Or Set In Memory 











\









\









\









\









\









\









\





\f

NTC-3: SPEED CONTROL ON/OFF SWITCH
Possible Causes:

manifold, sends input signal to Engine Control Module (ECM). ECM uses
input signal for controlling fuel control, timing and engine
protection. ECM will lower engine power if boost is too high.
Oil Pressure Sensor
Oil pressure sensor signal is input to Engine Control Module
(ECM). ECM converts signal to pressure value. Value is sent on CCD Bus\
to instrument panel gauge/light. Oil pressure sensor is located on
side of engine block, below ECM. See Fig. 2.
Power Take Off (PTO)
This input is used on vehicles equipped with a Power Take Off
(PTO) unit. When PTO is engaged, Engine Control Module (ECM) will
disable some OBD-II functions.
Water-In-Fuel (WIF) Sensor
WIF sensor is located in bottom of fuel filter/water
separator. See Fig. 2. WIF sensor delivers input signal to Engine
Control Module (ECM) when water exists in the fuel filter/water
separator. As water level increases, resistance across WIF sensor
decreases. ECM compares decrease in resistance to a high water
standard value. When resistance is 30,000-40,000 ohms, ECM will turn
on WATER-IN-FUEL warning light. WATER-IN-FUEL warning light is located
on instrument panel, just below tachometer. ECM monitors input signal
when ignition switch is in the ON position and continues to monitor
input signal until intake manifold air heater post-heat cycle is
complete.
PCM INPUT SIGNALS
A/C Switch
When A/C switch is in ON position, an input signal is
delivered from A/C switch to Engine Control Module (ECM) to indicate
that A/C operation has been requested. Once A/C operation has been
requested, an A/C request signal is delivered to ECM from A/C high-
pressure switch and A/C low-pressure switch. The A/C request signal
indicates evaporator pressure is within proper range for A/C
operation. ECM uses A/C request signal to cycle A/C compressor clutch
by using an A/C clutch relay. A/C clutch relay may also be referred to
as A/C compressor clutch relay. If A/C high-pressure switch or A/C
low-pressure switch opens, A/C request signal will not be delivered to
the ECM. ECM will then open ground circuit for A/C clutch relay and
A/C compressor clutch will be disengaged.
The A/C clutch relay is located in power distribution center
at driver's side front corner of engine compartment, near the battery.
The A/C high-pressure switch is located on discharge line, near A/C
compressor. The A/C low-pressure switch is located on top of
accumulator.
Accelerator Pedal Position Sensor (APPS) Output From ECM
Accelerator Pedal Position Sensor (APPS) is mounted on top
left of engine. See Fig. 2. Sensor provides DC voltage input signal to
Engine Control Module (ECM) to indicate throttle position. On previous\
engines, there were linkages between accelerator pedal, throttle
position sensor and injection pump. On this engine, no linkage exists
between accelerator pedal and injection pump. APPS signal is sent on
CCD Bus circuit from ECM to PCM.
Automatic Shutdown (ASD) Relay
A 12-volt input signal is delivered from ASD relay to Engine
Control Module (ECM) when ASD relay is energized. If ECM does not
receive a 12-volt input signal when ASD relay is energized, a
Diagnostic Trouble Code (FTC) will be stored in ECM. ASD relay is

located in power distribution center at driver's side front corner of
engine compartment, near the battery. Automatic Shutdown (ASD) relay
may also be referred to as Auto Shutdown (ASD) relay.
Battery Temperature Sensor
Battery temperature sensor delivers input signal to
Powertrain Control Module (PCM) to indicate the battery temperature.
PCM uses battery temperature input to modify rate of output from the
charging system. Battery temperature sensor is snapped into battery
tray below driver's side battery.
Battery Voltage
Battery voltage input signal provides operating voltage to
Powertrain Control Module (PCM). This input signal keeps PCM memory
alive and informs PCM what generator output voltage is when engine is
running. PCM memory is used to store Diagnostic Trouble Codes (DTCs),
store APPS sensor voltages from previous key cycles and provide a
speed control adaptive memory.
Brake Switch
Brake switch delivers input signal to Powertrain Control
Module (PCM) to indicate when brakes are applied. PCM uses input
signal for controlling cruise control system and transmission torque
converter clutch operation on A/T models. Brake switch is located near
top of brake pedal and may also be referred to as brakelight switch.
CKP Sensor
Crankshaft Position (CKP) sensor delivers input signal (35
tooth wheel with gap) to Engine Control Module (ECM) to indicate
engine speed and crankshaft position. ECM uses CKP signal along with
other input signals for controlling injector firing sequence and
timing. Sensor is located below fuel transfer pump, on side of engine
block. See Fig. 2.
Cruise Control System Switches
Cruise control system functions, controlled by momentary
contact switches, are monitored through multiplexed input signal to
Powertrain Control Module (PCM). Resistance monitored at this input
signal, in conjunction with the length of time the PCM measures the
resistance, determines which switch feature has been selected.
Data Link Connector (DLC)
Data Link Connector (DLC) provides an input signal to
Powertrain Control Module (PCM) when using scan tool to retrieve
Diagnostic Trouble Codes (DTCs) from PCM. Input signal may also be
used when performing various tests on the PCM and electronic control
system. DLC is a 16-pin connector located at lower edge of driver's
side of instrument panel, just above accelerator pedal.
Fuel Level Sensor
The Powertrain Control Module (PCM) sends a 5-volt signal to
the fuel level sensor. The fuel level sensor will return a signal to
PCM. This signal is used for fuel gauge operation and to prevent
setting a false misfire or fuel system trouble codes. If fuel level is
less than 15 percent, PCM will not set code.
Ignition Sense
Ignition switch position input to Powertrain Control Module
(PCM). PCM uses input to determine proper output functions, including
cruise control, generator output, sensor supply and transmission
functions.
Transmission Speed Sensor (A/T Models)

WAIT-TO-START Warning Light
WAIT-TO-START warning light is located on instrument panel,
just below the speedometer. WAIT-TO-START warning light will come on
for a short period and then go off as a bulb and wiring circuit test
each time ignition switch is turned to the ON position. If Engine
Control Module (ECM) determines intake manifold air temperature is
less than 59
F (15C) by input signal received from intake manifold
air temperature sensor, ECM delivers output signal to operate WAIT-TO-
START warning light and intake manifold air heater for a preheat
cycle.
WAIT-TO-START warning light will remain on until intake
manifold air heater preheat cycle is complete. WAIT-TO-START warning
light will flash on and off if intake manifold air temperature sensor
signal to ECM is not within a specified value and Diagnostic Trouble
Code (FTC) will be stored in ECM memory.
WATER-IN-FUEL Warning Light
WATER-IN-FUEL warning light is located on instrument panel,
just below tachometer. WATER-IN-FUEL warning light will come on for a
short period and then go off as a bulb and wiring circuit test each
time ignition switch is turned to the ON position. If Engine Control
Module (ECM) determines water exists in fuel/water separator by input
signal from Water-In-Fuel (WIF) sensor, ECM will deliver output signal\
to turn on the WATER-IN-FUEL warning light.
ECM/PCM OUTPUT SIGNALS
A/C Clutch Relay
The Engine Control Module (ECM) controls A/C compressor
operation by controlling ground circuit for A/C clutch relay. ECM de-
energizes A/C clutch relay if engine coolant temperature is more than
257
F (125C). The A/C clutch relay is located in power distribution
center at driver's side front corner of engine compartment, near the
battery.
Automatic Shutdown (ASD) Relay
The Engine Control Module (ECM) controls ASD operation by
controlling ground circuit for ASD relay. ASD provides voltage to
operate generator field control for charging system. ASD relay is
located in power distribution center at driver's side front corner of
engine compartment, near the battery. Automatic Shutdown (ASD) relay
may also be referred to as Auto Shutdown (ASD) relay.
CCD Bus
These circuits are connected between Engine Control Module
(ECM) and Powertrain Control Module (PCM) to allow communication
between modules.
Cruise Control System
Engine Control Module (ECM) regulates cruise control system
operation by controlling vacuum at cruise control servo. Vacuum is
controlled by use of vacuum and vent solenoids in cruise control
servo.
Data Link Connector
Engine Control Module (ECM) provides output information at
Data Link Connector (DLC) when using scan tool to perform various
tests on the ECM and electronic control system. Data link connector is
a 16-pin connector located at lower edge of driver's side of
instrument panel, just above the accelerator pedal.
5-Volt Sensor Supply Output
Powertrain Control Module (PCM) supplies a 5-volt reference

converter lock-up. ECM uses various input signals such as transmission
temperature, output shaft speed, central module timer, engine speed,
APPS and brake switch position to determine operation of transmission
torque converter clutch solenoid. Transmission torque converter clutch
solenoid is located on transmission valve body.
FUEL SYSTEM
FUEL DELIVERY
Fuel Injection Pump
A camshaft-driven Bosch VP44 in-line fuel injection pump is
used to supply high pressure fuel to each fuel injector in precise
metered amounts at the correct time. See Fig. 2. The pump is timed to
camshaft gear. Pump output is controlled by integral Fuel Pump Control
Module (FPCM). Because of electronic control, idle speeds and pump
timing are not adjustable. See ON-VEHICLE ADJUSTMENTS - TRUCKS -
DIESEL article. FPCM can operate engine if crankshaft position sensor
signal does not exist. Fuel injection occurs near completion of
compression stroke for each cylinder.
Fuel injection pump contains an overflow valve which allows
excess fuel to return to the fuel tank. Overflow valve is located on
side of fuel injection pump and is used to attach the fuel return line
to the fuel injection pump.
Fuel Transfer Pump
Fuel transfer pump is located on driver's side of cylinder
block, above starter. See Fig. 2. A 12 volt, 12-amp electric vane-type
pump supplies low fuel pressure from fuel tank, through fuel
heater/fuel filter/water separator to fuel injection pump. Fuel
transfer pump contains internal check valves to prevent fuel from
bleeding back into fuel tank during engine shutdown. Pump will self
prime with ignition on for 2 seconds. Pump has 2 modes, 100 percent
duty cycle (10 psi) when engine is running and 25 percent duty cycle
(7 psi) when engine is cranking.
Fuel Filter/Water Separator
Fuel filter/water separator, located on left side of engine,
protects injection pump by removing water and contaminants from fuel.
See Fig. 2 . Assembly also includes fuel heater and Water-In-Fuel (WIF)
sensor.
In-Tank Fuel Filter
A separate in-tank fuel filter is attached to bottom of fuel
tank module. In-tank fuel filter does not require service under normal
conditions.
FUEL CONTROL
Fuel Injector
Fuel injector delivers atomized fuel into the cylinder.
During fuel injection, fuel pressure from fuel injection pump
increases to fuel injector opening pressure or pop pressure of 4500
psi (316 kg/cm

). This is the pressure required to lift fuel injector
needle valve from its seat, allowing fuel to be injected into the
cylinder. Once fuel pressure decreases to less then the opening
pressure, a spring forces needle valve closed and stops fuel injection
into the cylinders. Each fuel injector is connected to injection pump
by a high pressure (as much as 17,405 psi) line.
Fuel Injection Timing
Pump output is controlled by integral Fuel Pump Control