1999 DODGE RAM fuel

Caravan
2.4L & 3.0L ............ (2) 43-53 (3.0-3.7) ............... ( 3)
3.3L
Flex-Fuel ............. ( 2) 50-60 (3.5-4.2) ............... ( 3)
Except Flex-Fuel ...... ( 2) 43-53 (3.0-3.7) ............... ( 3)
3.8L ................... ( 2) 43-53 (3.0-3.7) ............... ( 3)
Dakota & Durango ......... ( 1) 44-54 (3.0-3.8) ........... .5 (24)
Ram Pickup, Ram Van
& Ram Wagon ............. ( 1) 44-54 (3.0-3.8) ........... .5 (24)
Town & Country
3.3L
Flex-Fuel ............. ( 2) 50-60 (3.5-4.2) ............... ( 3)
Except Flex-Fuel ...... ( 2) 43-53 (3.0-3.7) ............... ( 3)
3.8L ................... ( 2) 43-53 (3.0-3.7) ............... ( 3)
Voyager
2.4L & 3.0L ............ ( 2) 43-53 (3.0-3.7) ............... ( 3)
3.3L
Flex-Fuel ............. ( 2) 50-60 (3.5-4.2) ............... ( 3)
Except Flex-Fuel ...... ( 2) 43-53 (3.0-3.7) ............... ( 3)
( 1) - Manufacturer lists fuel pressure with engine idling.
( 2) - Manufacturer lists fuel pressure with engine off, ignition on
and using scan tool to activate fuel pump.
( 3) - Information is not available from manufacturer.









\









\









\









\









\









\









\







FUEL INJECTION PUMP & FUEL TRANSFER PUMP (DIESEL)
NOTE: For fuel injection pump timing, see appropriate ON-VEHICLE
ADJUSTMENTS article.
FUEL INJECTION PUMP PERFORMANCE (DIESEL)









\









\









\









\









\









\









\







Application Output Pressure psi (kg/cm)
Ram Pickup 5.9L ................................................ ( 1)
( 1) - Pressure testing procedure and output pressure is not available
from manufacturer.









\









\









\









\









\









\









\







NOTE: For testing of fuel transfer pump, see appropriate BASIC
DIAGNOSTIC PROCEDURES article.
INJECTOR OPENING PRESSURE (DIESEL)
INJECTOR OPENING PRESSURE (DIESEL)








\









\









\









\









\









\









\







Application psi (kg/cm)
Ram Pickup 5.9L ......................................... 4500 (316)\









\









\









\









\









\









\









\







INJECTOR RESISTANCE
INJECTOR RESISTANCE








\









\









\









\









\









\









\







Application Ohms @ 68F (20C)
All Models ................................................... 10-16









\









\









\









\









\









\









\

ON-VEHICLE TESTING
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
DISABLING/ENABLING IGNITION & FUEL SYSTEMS
WARNING: To prevent engine from starting while performing tests,
always disable ignition and fuel systems.
Disabling Ignition & Fuel Systems
Remove Automatic Shutdown Relay (ASD) located in Power
Distribution Center (PDC). Refer to PDC cover for proper relay
location. PDC is located in engine compartment. On 5.9L diesel
engines, also disconnect fuel shutdown solenoid connector. Solenoid is
located behind upper intake manifold. See appropriate SYSTEM &
COMPONENT TESTING article in ENGINE PERFORMANCE section.
Enabling Ignition & Fuel Systems
When testing and/or repairs have been completed, verify
battery condition. Recharge battery as necessary, after starter tests
have been completed. Disconnect all test equipment. Install ASD relay.
On 5.9L diesel engines, reconnect fuel shutdown relay connector. On
all models, start engine several times to verify malfunction has been
corrected.
CRANKING TEST
NOTE: Ensure engine is at normal operating temperature. High
viscosity oil, extreme cold temperatures, or tight engine
will increase amperage draw.
1) Using a battery load tester, connect positive and negative
leads to battery. Connect inductive ammeter pick-up to positive
battery cable. Disable ignition and fuel systems. See
DISABLING/ENABLING IGNITION & FUEL SYSTEMS.
2) Ensure all lights and accessories are off. Place A/T in
Park position or M/T in Neutral position. Apply parking brake. Crank
engine and observe voltmeter reading. If voltage is more than 9.6
volts and cranking amperage draw is more than specified amps, proceed
to CIRCUIT RESISTANCE TESTS. See STARTER SPECIFICATIONS - CARS or
STARTER SPECIFICATIONS - TRUCKS.
3) If voltage is 12.5 volts or more and cranking amperage
draw is less than specified, check starter circuit components in the
following order:
starter solenoid, starter relay, starter relay circuit, park/neutral
position switch or transmission range sensor (A/T), clutch pedal
position switch (M/T), ignition switch, wiring harness and
connections.
CIRCUIT RESISTANCE TESTS
NOTE: If excessive resistance is not found in circuits being
tested, remove starter and proceed to BENCH TESTING.
Battery Connection Resistance Test
1) Disable vehicle ignition and fuel systems. See
DISABLING/ENABLING IGNITION & FUEL SYSTEMS. A voltmeter accurate to
one tenth of a volt will be needed for the following tests.

2) Connect voltmeter positive lead to negative battery cable
clamp. Connect voltmeter negative lead to negative battery post. Crank
engine and observe voltmeter reading. If voltage is detected, repair
poor contact between cable clamp and post. Perform same procedure to
positive battery post and cable clamp.
Ground Connection Resistance Test
Connect voltmeter negative lead to negative battery post.
Connect voltmeter positive lead to engine block, near negative battery
cable grounding point. Crank engine and observe voltmeter reading. If
voltmeter reading indicates more than 0.2 volt, repair poor ground
connection or replace ground cable.
Starter Ground Connection Resistance Test
Connect voltmeter negative lead to negative battery post.
Connect voltmeter positive lead to starter housing. Crank engine and
observe voltmeter reading. If voltmeter reading indicates more than 0.
2 volt, repair poor starter-to-ground connection.
Positive Battery Cable Resistance Test
1) Remove starter heat shield (if equipped) to gain access t\
o
starter solenoid connections. Connect voltmeter negative lead to
starter solenoid battery terminal and voltmeter positive lead to
positive battery post.
2) Crank engine and observe voltmeter reading. If voltage
reads more than 0.2 volt, correct poor connection between battery
cable and starter solenoid or replace positive battery cable.
SOLENOID CIRCUIT TEST
NOTE: Perform SOLENOID CIRCUIT TEST before testing starter relay
and starter relay circuit. Ensure A/T is in Park position or
M/T is in Neutral position and parking brake is applied.
1) Disable vehicle ignition and fuel systems. See
DISABLING/ENABLING IGNITION & FUEL SYSTEMS.
2) Ensure battery is fully charged. Ensure solenoid
connections are not loose or corroded. Remove starter relay from Power
Distribution Center (PDC). Refer to PDC cover for proper relay
location. PDC is located in engine compartment.
3) Connect a remote starter switch or jumper wire between
starter relay socket terminal No. 87 and positive battery post. See
Fig. 1 or 2. If engine cranks, solenoid and starter are good. Go to
STARTER RELAY TEST.
4) If engine fails to crank, or if solenoid chatters, check
wiring and connectors from starter relay socket to starter solenoid
terminal. Repair any loose or corroded connections. If engine still
fails to crank, remove starter and proceed to SOLENOID TEST under
BENCH TESTING.
STARTER RELAY TEST
NOTE: Perform SOLENOID CIRCUIT TEST before testing starter relay.
Remove starter relay from Power Distribution Center (PDC).
Refer to PDC cover for proper relay location. PDC is located in engine
compartment. Connect 12-volt power source to starter relay terminal
No. 86 and ground terminal No. 85. See Fig. 1 or 2. Using ohmmeter,
check continuity across starter relay terminals No. 30 and 87. If
continuity is not present, replace starter relay.

Fig. 1: Locating Powertrain Control Module (PCM)
Courtesy of Chrysler Corp.
ENGINE SENSORS & SWITCHES
SENSORS
Battery Temperature Sensor
1) Battery temperature sensor is snapped into battery tray,
below driver's side battery. Disconnect wiring harness at battery
temperature sensor.
2) Using ohmmeter, check resistance between electrical
terminals on battery temperature sensor. Resistance should be 9000-11,
000 ohms at 75-80
F (25-27C). Replace battery temperature sensor if
resistance is not within specification.
3) If problem exists in battery temperature sensor or wiring
circuit, a Diagnostic Trouble Code (DTC) will be stored in Powertrain
Control Module (PCM). See SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS
article.
Crankshaft Position Sensor
If problem exists in crankshaft position sensor, a Diagnostic
Trouble Code (DTC) will be stored in Powertrain Control Module (PCM)\
.
See appropriate crankshaft position sensor test in SELF-DIAGNOSTICS -
JEEP, TRUCKS & RWD VANS article.
Fuel Heater Temperature Sensor
See FUEL DELIVERY under FUEL SYSTEM.
Intake Manifold Air Temperature Sensor
Intake manifold air temperature sensor is located on top of
intake manifold, behind intake manifold air heater. For testing, see
DTC P0113: INTAKE AIR TEMPERATURE SENSOR VOLTAGE HIGH test in SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
Transmission Governor Pressure Sensor (A/T Models)

See TRANSMISSION under MISCELLANEOUS CONTROLS.
Transmission Speed Sensor (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
Transmission Temperature Sensor (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
Water-In-Fuel (WIF) Sensor
Water-in-fuel sensor is located in bottom of fuel
filter/water separator. Testing information not available from
manufacturer.
SWITCHES
Brake Switch
1) Remove lower panel for access to brake switch. Brake
switch is located on bracket, near top of brake pedal. Disconnect
electrical connector from brake switch. Pull plunger on brake switch
fully outward. See Fig. 2.
2) Using ohmmeter, check for continuity between terminals No.
5 and 6 on brake switch. See Fig. 2. Continuity should exist. If
continuity exists, go to next step. If continuity does not exist,
replace brake switch.
3) Push plunger on brake switch fully inward. Using ohmmeter,
check for continuity between terminals No. 1 and 2, and 3 and 4 on
brake switch. See Fig. 2. Continuity should exist. If continuity does
not exist, replace brake switch.
Fig. 2: Identifying Brake Switch Terminals
Courtesy of Chrysler Corp.
Park/Neutral Switch (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.

Transmission Overdrive Switch (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
RELAYS & SOLENOIDS
RELAYS
A/C Clutch Relay
A/C clutch relay may also be referred to as A/C compressor
clutch relay. A/C clutch relay is located in power distribution center
at driver's side front corner of engine compartment, near battery. If
problem exists in A/C clutch relay or wiring circuit, a Diagnostic
Trouble Code (DTC) will be stored in Powertrain Control Module (PCM)\
.
See DTC P0645 in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
Auto Shutdown (ASD) Relay
ASD relay is located in power distribution center at driver's
side front corner of engine compartment, near battery. If problem
exists in ASD relay or wiring circuit, a Diagnostic Trouble Code (DTC)\
will be stored in Powertrain Control Module (PCM). See SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
Fuel Heater Relay
1) Fuel heater relay is located in Power Distribution Center
(PDC) next to left battery. Refer to PDC lid for relay location.
Remove relay and note terminal identification on relay. See Fig. 3.
2) Using ohmmeter, check resistance between terminals No. 85
and 86 on relay. Resistance should be 70-80 ohms. If resistance is
within specification, go to next step. If resistance is not within
specification, replace relay.
3) Using ohmmeter, ensure continuity exists between terminals
No. 30 and 87A on relay. If continuity exists, go to next step. If no
continuity exists, replace relay.
4) Using ohmmeter, ensure no continuity exists between
terminals No. 30 and 87 on relay. If no continuity exists, go to next
step. If continuity exists, replace relay.
5) Using jumper wires, connect terminal No. 85 to negative
side of 12-volt power source and terminal No. 86 to positive side of
12-volt power source. Using ohmmeter, ensure no continuity now exists
between terminals No. 30 and 87A on relay. If no continuity exists, go
to next step. If continuity exists, replace relay.
CAUTION: DO NOT allow ohmmeter leads to contact terminals No. 85 and
86 on relay when checking resistance.
6) Using ohmmeter, ensure continuity now exists between
terminals No. 30 and 87 on relay. If continuity exists, disconnect
jumper wires from relay. If no continuity exists, replace relay.
NOTE: For additional information on checking wiring circuit for
fuel heater relay, see TEST NTC-1: NO TROUBLE CODE TEST MENU
and TEST NS-SEL: NO START TEST SELECTION in SELF-DIAGNOSTICS
- JEEP, TRUCKS & RWD VANS article.

Fig. 3: Fuel Heater Relay Terminals
Courtesy of Chrysler Corp.
Intake Manifold Air Heater Relays
1) Intake manifold air heater relays may also be referred to
as intake air heater relays. Intake manifold air heater relays are
mounted on inner wheelwell, below driver's side battery. See Fig. 4.
2) Disconnect negative battery cables. Note location of
wiring on intake manifold air heater relays for reassembly reference.
Disconnect all electrical connectors and cables from intake manifold
air heater relays.
3) Connect ohmmeter between large terminals on intake
manifold air heater relay to check for continuity. Using jumper wires,
momentarily apply battery voltage to relay trigger wire terminals
(small wire terminals) at base of intake manifold air heater relay.
See Fig. 4 . Polarity is not important.
4) Intake manifold air heater relay should click and ohmmeter
should indicate continuity between large terminals when battery
voltage is applied to relay trigger wire terminals. If intake manifold
air heater relay operation is not as specified, replace intake
manifold air heater relay with bracket. Test remaining intake manifold
air heater relay. Remove ohmmeter. Reconnect all electrical connectors
and negative battery cables.
NOTE: For additional information on checking wiring circuit for
intake manifold air heater relay, see DTC P0380: INTAKE AIR
HEATER RELAY NO. 1 CONTROL CIRCUIT and DTC P0382: INTAKE AIR
HEATER RELAY NO. 2 CONTROL CIRCUIT tests in SELF-DIAGNOSTICS
- JEEP, TRUCKS & RWD VANS article.

Transmission Torque Converter Clutch Solenoid (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
Fig. 5: Locating Fuel System Components
Courtesy of Chrysler Corp.
FUEL SYSTEM