1999 DODGE RAM oil filter

 5.9L: If mileage is less than 6,000 miles (9,600 Km) Yearly, 

replace the oil filter at every oil change. 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 0 F SAE 10W-30 

(
1)  (-18C) To Over 100F (38C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 5W-30 

-20F (-29C) Up To 32F (0C) 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  5.9L: Drained, W/New Filter  5 Qts. (4.7L) 


\
\
\

\
\


 8.0L: Drained, W/New Filter  5 Qts. (4.7L) 


\
\
\

\
\


 5.9L: Drained  4.5 Qts. (4.2L) 

\

\
\
\

\
\
\


Engine  5.9L: Drained  20 Qts. (19L) 

Coolant 
\
\
\

\
\


 8.0L: Drained  24 Qts. (22.7L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


117,000 MILE (185,000 KM) SEVERE DUTY SERVICE
117,000 MILE (185,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


  Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter (
1) 

\
\
\
\
\
\
\


(
1)  8.0L: Change oil filter at every oil change. 

5.9L: If mileage is less than 6,000 miles (9,600 Km) Yearly, 

replace the oil filter at every oil change. 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 0 F SAE 10W-30 

(
1)  (-18C) To Over 100F (38C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 5W-30 

-20F (-29C) Up To 32F (0C) 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  5.9L: Drained, W/New Filter  5 Qts. (4.7L) 


\
\
\

\
\


 8.0L: Drained, W/New Filter  5 Qts. (4.7L) 


\
\
\

\
\


 5.9L: Drained  4.5 Qts. (4.2L) 

\

\
\
\

\
\
\


Engine  5.9L: Drained  20 Qts. (19L) 

Coolant 
\
\
\

\
\


 8.0L: Drained  24 Qts. (22.7L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


120,000 MILE (199,000 KM) SEVERE DUTY SERVICE
120,000 MILE (199,000 KM) SEVERE DUTY SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

SC HED ULE D S ER VIC ES
 


INSPECT 



 Exhaust System 




 Brake Hoses 




 Engine Coolant Level, Hoses & Clamps 




 Engine Air Cleaner & Air Pump Filters 




 Brake Linings 




SERVICE 



 Lubricate Steering Linkage 




 Automatic Transmission Bands 




 Clean EGR Passages (5.9L) 




REPLACE 



 Engine Oil 




 Engine Oil Filter (
1) 




 Automatic Transmission Fluid & Filter 




 Rear Axle Fluid 




 Front Axle Fluid (4x4) 




 Spark Plugs 




 Ignition Cables 




 PCV Valve (5.9L) 




 EGR Valve (5.9L) 




 Distributor Cap & Rotor (5.9L) 



(
1)  8.0L: Change oil filter at every oil change. 

5.9L: If mileage is less than 6,000 miles (9,600 Km) Yearly, 

replace the oil filter at every oil change. 




LUBRICATION SPECIFICATIONS 




Material  Condition  Specification 





Engine Oil Ambient Temperature Above 0 F SAE 10W-30 

(
1)  (-18C) To Over 100F (38C)  





Ambient Temperature Less Than  SAE 5W-30 

-20F (-29C) Up To 32F (0C) 





Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 





Brake Fluid  All  DOT 3 





SC HED ULE D S ER VIC ES
 Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   





Automatic  All  ATF+2 Type 7176 

Transmission   

Fluid   





Rear Axle  All Mopar Hypoid Lubricant 

Lubricant   SAE 80W-90 

(
2)   GL-5 Gear Lube 





4x4 Front  All Mopar Hypoid Lubricant 

Axle   SAE 80W-90 

Lubricant   GL-5 Gear Lube 



(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

(
2) - Axles with Limited-Slip Differentials require the use of 

a 5% Friction Modifier, such as Mopar Gear Oil Additive 

Friction Modifier. 




FLUID CAPACITIES 




Item  Condition  Specification (1) 





Engine Oil  5.9L: Drained, W/New Filter  5 Qts. (4.7L) 





 8.0L: Drained, W/New Filter  5 Qts. (4.7L) 





 5.9L: Drained  4.5 Qts. (4.2L) 





Engine  5.9L: Drained  20 Qts. (19L) 

Coolant 



 8.0L: Drained  24 Qts. (22.7L) 





Automatic  47RE: Dry Fill  1733 Pts. (815.6L) 

Transmission   

Fluid   





Rear Axle  9-1/4: Drained  4.8 Pts. (2.3L) 

Fluid 



 Model 248 (2WD)  6.3 Pts. (3L) 





 Model 248 (4WD)  7.3 Pts. (3.4L) 





 Model 267 (2WD)  7 Pts. (3.3L) 





 Model 267 (4WD)  7.8 Pts. (3.6L) 





 Model 286 (2WD)  6.8.Pts. (3.2L) 





 Model 286 (4WD)  10.1 Pts. (4.8L) 





Rear Axle  Model 248 (2WD)  6.3 Pts. (3L) 

Limited Slip 



Differential  Model 248 (4WD)  7.3 Pts. (3.4L) 





 Model 267 (2WD)  7 Pts. (3.3L) 





 Model 267 (4WD)  7.8 Pts. (3.6L) 





 Model 286 (2WD)  6.8 Pts. (3.2L) 

SC HED ULE D S ER VIC ES
 Lubricant   GL-5 Gear Lube 





Power  All  Mopar Power Steering 

Steering   Fluid Or Equivalant 

Fluid (
3)   Petroleum Based 





Clutch  All  Multipurpose Grease 

Linkage   NLGI Grade 2 E.P. 

Lubricant   





A/C  All  R-134a 

Refrigerant   





A/C  All  Polyalkalene Glycol 

Refrigerant   SP10 PAG 

Oil   Refrigerant Oil 





(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

(
2) - Axles with Limited-Slip Differentials require the use of 

a 5% Friction Modifier, such as Mopar Gear Oil Additive 

Friction Modifier. 

(
3) - Never add gear oil, automatic transmission fluid or 

hydroboost power steering fluid. 



FLUID CAPACITIES
FLUID CAPACITIES TABLE



Item  Condition  Specification (1) 





Engine Oil  5.9L: Drained, W/New Filter  5 Qts. (4.7L) 





 8.0L: Drained, W/New Filter  5 Qts. (4.7L) 





 5.9L: Drained  4.5 Qts. (4.2L) 





Engine  5.9L: Drained  20 Qts. (19L) 

Coolant 



(
2)  8.0L: Drained  24 Qts. (22.7L) 





Automatic  46RE: Dry Fill  1726 Pts. (812.3L) 

Transmission 



Fluid  47RE: Dry Fill  1733 Pts. (815.6L) 





Manual  NV3500  4.2 Pts. (2L) 

Transmission 



Fluid  NV4500  8 Pts. (3.8L) 





Rear Axle  9-1/4: Drained  4.8 Pts. (2.3L) 

Lubricant 



 Model 248 (2WD)  6.3 Pts. (3L) 





 Model 248 (4WD)  7.3 Pts. (3.4L) 





 Model 267 (2WD)  7 Pts. (3.3L) 





 Model 267 (4WD)  7.8 Pts. (3.6L) 





 Model 286 (2WD)  6.8.Pts. (3.2L) 

2.4L ........................................... 11.2 Qts. (10.6L)\
3.0L ........................................... 13.0 Qts. (12.3L)\
3.3L & 3.8L .................................... 13.2 Qts. (12.5L)\
Automatic Transaxle (Mopar ATF Plus Type 7176)
3-Speed
Drain & Refill .............................. (4) 4.0 Qts. (3.8L)
Dry Refill ...................................... 8.5 Qts. (8.0L)\
4-Speed
Drain & Refill .............................. ( 4) 4.0 Qts. (3.8L)
Dry Refill ...................................... 9.1 Qts. (8.6L)\
Overrunning Clutch
(Mopar ATF Plus Type 7176 - AWD Models) ...................... ( 5)
Power Steering Fluid ( 6) ............................ 1.7 Pts. (.8L)
Power Transfer Unit
(SAE 80W-90/API GL-5 - AWD Models) .............. 1.2 Qts. (1.14L\
)
Rear Differential
(SAE 80W-90/API GL-5 - AWD Models) ( 5) ....................... ( 7)
( 1) - Approximate quantity listed.
( 2) - Use an API energy conserving engine oil that is certified for
gasoline engines on all engines except 3.3L flex-fuel models.
On 3.3L flex-fuel models, use Mopar Flex-Fuel 5W-30 engine oil
or an equivalent that meets Chrysler Standard MS-9214. Proper
engine oil MUST BE used to prevent engine damage. The 3.3L
flex-fuel model may be referred to as Flex-Fuel Vehicle (FFV)
model and is used in all vehicles except California emission
vehicles. Flex-fuel model may be also referred to as an E85
application and may be identified by label attached to inside of
gasoline filler door.
( 3) - Quantity includes heater and coolant recovery tank. Add 2 qts.
(1.9L) if equipped with rear heater.
( 4) - Add this amount of fluid. Start engine and shift transaxle
through all gears and back to Park. Add additional fluid to
bring fluid level to 1/8" below the ADD mark on dipstick.
Recheck fluid level with transaxle at normal operating
temperature. Adjust fluid level so fluid level is within the
HOT range dipstick.
( 5) - An overrunning clutch is bolted on front of rear differential,
between torque tube for drive shaft and rear differential.
Overrunning clutch contains a separate reservoir from rear
differential. Ensure fluids are checked at appropriate
component, as different types of fluids are used. Fluid capacity
is not available from manufacturer.
( 6) - Use only Mopar power steering fluid. DO NOT use automatic
transmission fluid.
( 7) - Capacity is not available from manufacturer. Fill unit until
fluid level is even with bottom of filler plug hole.









\









\









\









\









\









\









\







FLUID CAPACITIES (DAKOTA)








\









\









\









\









\









\









\







Application ( 1) Quantity
Crankcase (Includes Filter) ( 2)
2.5L ............................................. 4.5 Qts. (4.3L)\
3.9L ............................................. 4.0 Qts. (3.8L)\
5.2L & 5.9L ...................................... 5.0 Qts. (4.7L)\
Cooling System (Includes Heater)
2.5L ............................................. 9.8 Qts. (9.3L)\
3.9L ........................................... 14.0 Qts. (13.2L)\
5.2L & 5.9L .................................... 14.3 Qts. (13.5L)\
Automatic Transmission
(Mopar ATF Plus Type 7176)

Drain & Refill .............................. (3) 1.5 Qts. (1.4L)
Dry Refill ....................... ( 4) 10.0-11.5 Qts. (9.5-10.8L)
Manual Transmission ( 5)
AX 15 (SAE 75W-90/API GL-5) 2.5L & 3.9L .......... 3.3 Qts. (3.1L\
)
NV 3500 (Mopar M/T Lube, P/N 4761526) 5.2L ....... 2.1 Qts. (2.0L\
)
Front Differential (SAE 80W-90/API GL-5) ........... 3.0 Pts. (1.4L\
)
Rear Differential (SAE 80W-90/API GL-5) ( 6)
8 1/4" Ring Gear ( 7) ............................. 4.4 Pts. (2.1L)
9 1/4" Ring Gear ( 7) ............................. 4.8 Pts. (2.3L)
Power Steering Fluid ( 8)
2WD ............................................... 1.7 Pts. (.8L)\
4WD .............................................. 2.5 Pts. (1.2L)\
Transfer Case (Mopar ATF Plus Type 7176) ........... 2.5 Pts. (1.2L\
)
( 1) - Approximate quantity listed.
( 2) - Use an API energy conserving engine oil that is certified for
gasoline engines.
( 3) - Add this amount of fluid. Start engine and shift transmission
through all gears and back to Neutral. Add additional fluid to
bring fluid level to the MIN mark on dipstick. Recheck fluid
level with transmission at normal operating temperature. Adjust
fluid level to MAX mark on dipstick. Approximate drain and
refill capacity is 4.0 qts. (3.8L).
( 4) - Quantity may vary by type of oil cooler and oil cooler lines.
( 5) - Verify type of transmission used before servicing. The AX 15
uses a flywheel housing bolted to the front of the transmission.
The NV 3500 uses a flywheel housing which is an integral part of
the transmission housing.
( 6) - Models with Trac-Lok limited slip differential must have 5 ozs.
(.15L) of Mopar Trac-Lok Friction Modifier added if lubricant is\
changed.
( 7) - Rear differential may be identified by number of bolts on rear
cover. The 8 1/4" ring gear has 10 bolts on rear cover and 9
1/4" ring gear has 12 bolts on rear cover.
( 8) - Use only Mopar power steering fluid. DO NOT use automatic
transmission fluid.









\









\









\









\









\









\









\







FLUID CAPACITIES (DURANGO)








\









\









\









\









\









\









\







Application ( 1) Quantity
Crankcase (Includes Filter) ( 2)
3.9L ............................................. 4.0 Qts. (3.8L)\
5.2L & 5.9L ...................................... 5.0 Qts. (4.7L)\
Cooling System (Includes Heater)
3.9L ........................................... 14.0 Qts. (13.2L)\
5.2L & 5.9L .................................... 14.3 Qts. (13.5L)\
Automatic Transmission
(Mopar ATF Plus Type 7176)
Drain & Refill .............................. ( 3) 1.5 Qts. (1.4L)
Dry Refill ....................... ( 4) 10.0-11.5 Qts. (9.5-10.8L)
Front Differential
(SAE 80W-90/API GL-5) ............................. 3.0 Pts. (1.4L\
)
Rear Differential
(SAE 80W-90/API GL-5) ( 5)
8 1/4" Ring Gear ( 6) ............................ 4.4 Pts. (2.1L)
9 1/4" Ring Gear ( 6) ............................ 4.8 Pts. (2.3L)
Power Steering Fluid ( 7) ........................... 2.5 Pts. (1.2L)
Transfer Case (Mopar ATF Plus Type 7176) ( 8)
NV 231 & NV 231HD ................................ 2.5 Pts. (1.2L)\
NV 242 ........................................... 3.0 Pts. (1.4L)\

(1) - Approximate quantity listed.
( 2) - Use an API energy conserving engine oil that is certified for
gasoline engines.
( 3) - Add this amount of fluid. Start engine and shift transmission
through all gears and back to Neutral. Add additional fluid to
bring fluid level to the MIN mark on dipstick. Recheck fluid
level with transmission at normal operating temperature. Adjust
fluid level to MAX mark on dipstick. Approximate drain and
refill capacity is 4.0 qts. (3.8L).
( 4) - Quantity may vary by type of oil cooler and oil cooler lines.
( 5) - Models with Trac-Lok limited slip differential must have 5 ozs.
(.15L) of Mopar Trac-Lok Friction Modifier added if lubricant is\
changed.
( 6) - Rear differential may be identified by number of bolts on rear
cover. The 8 1/4" ring gear has 10 bolts on rear cover and 9
1/4" ring gear has 12 bolts on rear cover.
( 7) - Use only Mopar power steering fluid. DO NOT use automatic
transmission fluid.
( 8) - Transfer case may be identified by model number stamped on
identification tag on rear of transfer case, just above filler
plug.









\









\









\









\









\









\









\







FLUID CAPACITIES (RAM PICKUP)








\









\









\









\









\









\









\







Application ( 1) Quantity
Crankcase (Includes Filter) ( 2)
3.9L ............................................. 4.0 Qts. (3.8L)\
5.2L & 5.9L (Gasoline) ........................... 5.0 Qts. (4.7L\
)
5.9L (Diesel) .................................. 11.0 Qts. (10.4L\
)
8.0L ............................................. 7.0 Qts. (6.6L)\
Cooling System (Includes Heater)
3.9L, 5.2L & 5.9L (Gasoline) ................... 20.0 Qts. (18.9L\
)
5.9L (Diesel) .................................. 24.0 Qts. (22.7L\
)
8.0L ........................................... 26.0 Qts. (24.6L)\
Automatic Transmission
(Mopar ATF Plus Type 7176)
42RE (3.9L)
Drain & Refill .............................. ( 3) 1.5 Qts. (1.4L)
Dry Refill ........................ ( 4) 8.5-11.0 Qts. (8.0-10.4L)
46RE (3.9L, 5.2L & 5.9L Gasoline)
Drain & Refill .............................. ( 3) 1.5 Qts. (1.4L)
Dry Refill ........................ ( 4) 9.5-11.5 Qts. (8.9-10.8L)
47RE (5.9L Diesel & 8.0L)
Drain & Refill .............................. ( 3) 1.5 Qts. (1.4L)
Dry Refill ...................... ( 4) 14.5-16.5 Qts. (13.7-15.6L)
Manual Transmission ( 5)
NV 3500 (Mopar M/T Lube,
P/N 4761526 - 3.9L & 5.2L) ...................... 2.1 Qts. (2.0L)\
NV 4500 (Mopar M/T Lube,
P/N 4637579) ( 6) - 5.9L
(Gas & Diesel) & 8.0L .......................... 4.0 Qts. (3.8L\
)
NV 5600 (Mopar M/T Lube,
P/N 4761526) ( 6) ............................... 4.75 Qts. (4.5L)
Front Differential (SAE 80W-90/API GL-5)
Dana 44 (Model 216 - 1500 & 2500) ................ 4.8 Pts. (2.3L\
)
Dana 60 (Model 248 - 2500 & 3500) ................ 7.6 Pts. (3.6L\
)
Rear Differential
9 1/4" Ring Gear
(SAE 75W-90/API
GL-5 - 1500 & 2500) ( 7) ........................ 4.8 Pts. (2.3L)
Dana 60 (Model 248)