1999 DODGE RAM lock

NOTE: It is not necessary to replace shaft seal because of a small
amount of oil found on adjacent surfaces. A small amount of
oil is normal for lubrication purposes. Shaft seal should
only be replaced after a confirmed refrigerant leak is
found.
Removal
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Loosen and reposition compressor in
mounting bracket. Remove clutch plate and hub assembly. See CLUTCH
ASSEMBLY. See Fig. 2 or 3.
2) Remove shaft seal snap ring. Ensure all surfaces around
seal are clean. Insert Shaft Seal Remover/Installer (J-23128-A) into
shaft seal. Rotate handle clockwise to seat seal remover/installer in
seal. Remove shaft seal. Using "O" Ring Remover (J-9553-01), remove
"O" ring. Ensure shaft and inside of compressor neck are clean and
free of foreign material. Thoroughly clean "O" ring groove in front
head.
Installation
1) Install Shaft Seal Protector (J-34614) over compressor
shaft. With shaft seal protector in place, lubricate "O" ring with
refrigerant oil and install it on "O" Ring Installer (J-33011).
2) Insert "O" ring installer in compressor until it bottoms.
Move slide on "O" ring installer downward until "O" ring is released
into groove. Rotate installer to seat "O" ring. Remove "O" ring
installer.
3) Lubricate shaft seal with refrigerant oil. Install shaft
seal onto Seal Installer (J-23128-A). Install shaft seal so flared
side of lip seal is installed toward compressor. Expand seal using
shaft seal remover/installer. Install shaft seal on Seal Protector (J-
34614). Place seal protector over shaft.
4) Push shaft seal into compressor using a rotary motion
until seal bottoms. Install new snap ring with flat side against seal.
Install clutch plate and hub assembly onto compressor shaft. See
CLUTCH ASSEMBLY.
NIPPONDENSO 10-CYLINDER
CLUTCH ASSEMBLY
Removal & Installation (Metro & Tracker)
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove A/C compressor. Drain, measure
and discard refrigerant oil from compressor.
2) Using Clutch Plate Holder/Remover (J-41384) remove clutch\
plate nut, washer and clutch plate from compressor drive shaft. Remove
clutch pulley snap ring and shim. Using a plastic mallet, gently tap
and remove clutch pulley. Remove clutch coil wire retainer from
compressor. Remove clutch coil snap ring and clutch coil. See Fig. 4.
3) Install clutch coil and snap ring. Attach clutch coil wire
retainer to compressor. Install clutch pulley, snap ring and shim.
Install clutch plate to compressor shaft. Measure air gap between
clutch pulley and clutch plate.
4) Air gap should be 0.014-0.026" (0.35-0.65 mm). Add or
remove shims as necessary. Install compressor shaft nut and washer.
Tighten compressor shaft nut to 11-15 ft. lbs. (15-20 N.m). After
repairs, add NEW refrigerant oil to compressor equal to amount
drained. To complete installation, reverse removal procedure.
SHAFT SEAL

Ford Motor Co. (Taurus 3.4L SHO)
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove A/C compressor. Drain and measure
oil from compressor.
2) Remove pulley assembly. Using Spanner Wrench (T81P-19623-
MH), remove shaft nut and lock washer. Using a steering wheel puller,
remove clutch plate, shaft key and shim. Remove snap ring and pulley
assembly, by hand. If necessary, use a 3-jaw puller to remove pulley
assembly. Remove clutch coil wire from retaining brace on compressor.
Remove snap ring and clutch coil. See Fig. 1.
Installation
1) Install clutch coil. Ensure hole on back of clutch coil is
aligned with pin on compressor head. Install snap ring with beveled
side facing outward. Install clutch coil wire into retaining brace.
2) Slip pulley assembly onto compressor shaft and install
snap ring with beveled side facing outward. Install shim and shaft
key. Align clutch plate with shaft key and install clutch plate. Use
Hub Driven Plate Replacer (T80L-19703-F), if necessary. Using spanner
wrench, install lock washer and shaft nut. Tighten shaft nut to 10-14
ft. lbs. (14-19 N.m).
3) Using a feeler gauge, measure air gap between clutch plate
and pulley assembly at 3 equally spaced locations. Rotate pulley 180
degrees and measure air gap at 3 locations again. Air gap should be 0.
016-0.027" (0.41-0.69 mm). If air gap is not within specification, add\
or remove shims to obtain correct air gap.
4) Add correct amount of refrigerant oil to compressor and
install compressor. See COMPRESSOR REFRIGERANT OIL CHECKING. Evacuate
and charge A/C system. Perform leak test.
SANDEN MSC90-C SCROLL
CLUTCH ASSEMBLY
Removal
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove compressor. Drain oil from
compressor, and measure amount drained.
2) Remove pulley assembly. Using Spanner (MB991367) and Pins\
(MB991386), remove shaft nut. Remove clutch plate, snap ring and rotor\
assembly. Remove snap ring and clutch coil. See Fig. 6.
Installation
1) Install clutch coil. Ensure projection on back of clutch
coil is aligned with pin hole in compressor body. Install snap ring so
that tapered surface is facing outward.
2) Install rotor assembly and snap ring. Align match mark of
clutch plate with match mark of compressor shaft spline and install
clutch plate. Using spanner and pins, install shaft nut.
3) Using a feeler gauge, check air gap between clutch plate
and rotor assembly at more than one place. Air gap should be 0.016-0.
024" (0.40-0.60 mm). If air gap is not within specification, add or
remove shims as necessary. Install pulley assembly.
4) Add same amount of refrigerant oil to compressor as was
drained from it. Install A/C compressor. Evacuate and charge A/C
system. Perform leak test.

Fig. 6: Compressor Components (Sanden MSC90-C Scroll)
Courtesy of chrysler corp.
SANDEN SD-7H15 7-CYLINDER
NOTE: On Cherokee, Dakota, Durango, Ram Pickup and Wrangler,
compressor clutch can be serviced in vehicle, without
discharging A/C system.
CLUTCH ASSEMBLY
Removal (Cherokee, Dakota, Durango, Ram Pickup & Wrangler)
1) Disconnect and isolate negative battery cable. Remove
serpentine drive belt. Disconnect clutch coil harness connector.
Without disconnecting refrigerant lines, remove A/C compressor from
mounting bracket. Support compressor in engine compartment.
2) Using spanner wrench, hold clutch plate and remove
compressor shaft nut. See Fig. 1. Using a steering wheel puller,
remove clutch plate, compressor shaft key and shims. Remove external
front housing snap ring.
3) Install jaws of Rotor Puller (C-6141-1) into pulley snap
ring groove. Install Shaft Protector (C-6141-2) over compressor shaft.\
Install puller flange plate on jaws. Install Puller Through-Bolts (C-
6461) through puller flange plate into jaws and hand tighten. Tighten
pulley center bolt clockwise and remove pulley from compressor.
4) Remove clutch coil wire harness retainer from compressor
housing. Remove clutch coil snap ring and clutch coil.

Installation (Cherokee & Wrangler)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub. Using Installer (C-
6871), press pulley and bearing assembly onto compressor housing hub.
Thread installer on compressor shaft and tighten nut until pulley
assembly is seated.
2) Install external front snap ring with beveled side facing
outward. Ensure snap ring is properly seated. Install compressor shaft
key and original shims. Using a plastic mallet and Driver (C-6463),
install clutch plate on compressor shaft. Tighten compressor shaft nut
to 10 ft. lbs. (14 N.m).
3) Using feeler gauge, measure air gap between clutch plate
and pulley assembly in several areas. Air gap should be 0.016-0.031"
(0.41-0.79 mm). If air gap is not within specification, adjust shim
thickness as necessary. If air gap is not consistent around clutch
plate, lightly pry up or tap down on clutch plate to make corrections.
To complete installation, reverse removal procedure.
Installation (Dakota, Durango & Ram Pickup)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub.
2) Install Handle (6464) and Driver (6143) into pulley
assembly bearing cavity. Ensure outer edge of driver rests firmly on
inner race of bearing. Using hammer, install pulley and bearing
assembly. While tapping on handle, guide pulley and bearing assembly
to prevent binding. Ensure pulley assembly bottoms against compressor
housing. Install external snap ring.
3) Install original shim(s) and compressor shaft key. Use a
hammer and Shaft Protector (6141-2) to install clutch plate on
compressor shaft. Ensure clutch plate bottoms out on clutch shims.
Replace compressor shaft nut and tighten compressor shaft nut to 10
ft. lbs. (14 N.m).
4) Measure air gap between clutch plate and pulley assembly
in several areas. Air gap should be 0.016-0.031" (0.41-0.79 mm). If
air gap is not within specification, adjust shim thickness as
necessary. If air gap is not consistent around clutch plate, lightly
pry up or tap down on clutch plate to make corrections. To complete
installation, reverse removal procedure. Ensure A/C system operates
properly.
5) After completing compressor clutch installation, start
engine. Set A/C-heater control to recirculated air mode and high
blower motor speed. Set engine speed to 1500-2000 RPM. Cycle
compressor on for 5 seconds and off for 5 seconds, about 20 times to
break-in clutch.
Removal (Ford "F" Series Super Duty Pickup)
1) Disconnect and isolate negative battery cable. Discharge
A/C system, using approved refrigerant recovery/recycling equipment.
Disconnect clutch coil harness connector and remove compressor. Drain
oil from compressor, and measure amount drained.
2) Using Spanner Wrench (T70P-4067-A), hold clutch plate and\
remove compressor shaft nut. See Fig. 1. If necessary, use a steering
wheel puller to remove clutch plate and shim(s).
3) Using a flat-blade screwdriver, remove pulley assembly
bearing dust cover. Remove compressor shaft key and internal bearing
snap ring. Remove external front housing snap ring.
4) Install jaws of rotor puller into pulley assembly internal
bearing snap ring groove. Install shaft protector over compressor
shaft. Install puller flange plate on jaws. Install 2 puller bolts
through puller flange plate into jaws and hand tighten. Tighten pulley
center bolt clockwise and remove pulley assembly from compressor.

HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards

Application incorrect,
affecting air
conditioning
system performance ..... A .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bent, affecting air
conditioning system
performance ............ A .. Require repair or replacement.
Blocked, affecting air
conditioning system
performance ............ A .. Require repair or replacement.
Broken, affecting air
conditioning system
performance ............ A .. Require repair or replacement.
Cracked, affecting air
conditioning system
performance ............ A .. Require repair or replacement.
Loose, affecting air
conditioning system
performance ............ A ................. Require repair.
Loose, not affecting air
conditioning system
performance ............ 2 ................. Suggest repair.
Missing, affecting air
conditioning system
performance ............ C ............ Require replacement.









\









\









\









\









\









\









\


AIR DISTRIBUTION SYSTEM
See PLENUMS.
BELTS
BELT INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Alignment incorrect ..... B .......... ( 1) Further inspection
required.
Cracked ................. 1 ............ Suggest replacement.
Frayed .................. 1 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
Noisy ................... 2 .......... ( 2) Further inspection
required.
Plies separated ......... A ............ Require replacement.
Serpentine belt routed
incorrectly ............ B ................. Require repair.
Tension out of
specification .......... B ........... Require adjustment or
replacement.
Worn beyond
adjustment range ....... B ............ Require replacement.

SERVICE PORT INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Application
does not match
refrigerant type ....... B ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Valve cap leaking ....... A ... Require repair or replacement
of cap.
Valve cap missing ....... C .... Require replacement of valve
cap.
Valve core sticking ..... B .. Require repair or replacement.









\









\









\









\









\









\









\


SPRING LOCK COUPLINGS
SPRING LOCK COUPLING INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Leaking ................. A ........... ( 1) Require repair or
replacement.
( 1) - Require inspection of mating and sealing surface and
repair or replace as necessary.









\









\









\









\









\









\









\


SUCTION THROTTLING VALVES (STVS)
SUCTION THROTTLING VALVE (STV) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Connection damaged ...... B .. Require repair or replacement.
Fitting damaged ......... B .. Require repair or replacement.
Inoperative ............. A ........... ( 1) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.









\









\









\









\









\









\









\


SWITCHES (ELECTRICAL)
SWITCH (ELECTRICAL) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.

filter the refrigerant. The orifice tube is used to meter the flow of
liquid refrigerant into the evaporator core.
HIGH PRESSURE CUT-OUT SWITCH
High pressure cut-out switch is located on compressor
discharge line, near compressor. On Dakota and Ram Pickup, it is
connected in series with the clutch cycling pressure switch and
control panel, between ground and PCM.
On Durango, it is connected in series with the electronic
cycling clutch switch, low pressure cut-out switch and control panel,
between ground and PCM. PCM controls compressor clutch operation.
On all models, when discharge pressure reaches 450-490 psi
(31.6-34.5 kg/cm
), high pressure cut-out switch interrupts A/C
request signal to PCM. PCM de-energizes compressor clutch relay,
disengaging compressor clutch. When discharge pressure drops to 270-
330 psi (23.2-19 kg/cm
) switch will close, thus restoring A/C request
signal to PCM.
HIGH PRESSURE RELIEF VALVE
High pressure relief valve is located on compressor manifold.
Valve vents system pressure if pressure is greater than 500-600 psi
(35.1-42.2 kg/cm
). Valve will reset when pressure decreases to 400
psi (28.1 kg/cm).
LOW PRESSURE CUT-OUT SWITCH OPERATION
Durango
Low pressure cut-out switch is located on suction line near
firewall. It is connected in series with the electronic cycling clutch
switch, high pressure cut-out switch and control panel, between ground
and PCM. PCM controls compressor clutch operation.
When discharge pressure reaches 10 psi (.7 kg/cm
), switch
interrupts A/C request signal to PCM. PCM de-energizes compressor
clutch relay, disengaging compressor clutch. When discharge pressure
increases to 13-27 psi (.9-1.9 kg/cm
), switch will close thus
restoring A/C request signal to PCM.
ADJUSTMENTS
TEMPERATURE CONTROL CABLE ADJUSTMENT
Dakota & Durango
1) Ensure temperature control cable housing and core are
connected at both A/C-heater control panel and A/C-heater assembly.
Ensure A/C-heater control panel is installed.
2) Rotate temperature control knob so that knob pointer is at
12 o'clock position. Pull temperature control knob straight out from
A/C-heater control panel until perimeter of knob (not knob pointer)
protrudes about .25" (6 mm) from face of A/C-heater control panel.
3) Rotate temperature control knob clockwise so that knob
pointer is at one o'clock position. Push in on knob slightly and
continue rotating knob to its full clockwise stop. Place knob pointer
at a position about .32" (8 mm) beyond end of Red stripe. Release
knob. If knob is pointing at about .32" (8 mm) beyond end of Red
stripe, go to next step. If knob is not pointing at about .32" (8 mm)
beyond end of Red stripe, go back to step 2) and repeat adjustment
procedure.
4) Rotate temperature control knob counterclockwise so that
knob pointer is at 12 o'clock position. Push temperature control knob
straight into A/C-heater control panel until perimeter of knob (not