1999 DODGE RAM ECU

panel. To install, reverse removal procedure.
Fig. 6: Removing Cluster Bezel (Ram Pickup)
Courtesy of Chrysler Corp.
ACCUMULATOR
Removal & Installation
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
clutch cycling pressure switch connector.
2) On Dakota, remove nuts securing cruise control servo
mounting bracket to studs on cowl plenum panel (if equipped). Move
servo far enough to access accumulator refrigerant lines.
3) On all models, disconnect refrigerant lines from A/C
compressor and evaporator. Plug or cover all openings in A/C system.
Loosen support bracket screw. Remove accumulator.
4) To install, reverse removal procedure. Install new "O"
rings. Evacuate and charge A/C system.
BLOWER MOTOR
Removal (Dakota & Durango - Front)
1) Disconnect negative battery cable. Remove and disassemble
A/C-heater assembly. See A/C-HEATER ASSEMBLY. Disconnect blower motor
lead at bottom of housing. Remove 6 screws and blower motor housing
cover.
2) Remove 3 screws and blower motor and fan assembly. Place
reference marks on blower motor and fan for reassembly reference.
Remove blower fan retainer clip. Pull blower motor fan off blower
motor shaft.
Installation
Align reference marks. Press blower fan hub onto blower motor
shaft. Ensure retainer clip ears are indexed over flats of blower
motor shaft and fan hub. To complete installation, reverse removal

install, reverse removal procedure.
Removal & Installation (Ram Pickup - Front)
Blower motor resistor is located under glove box, attached to
blower motor housing. See Fig. 5. Disconnect negative battery cable.
Remove blower motor resistor connector. Remove resistor retaining
screws. Remove blower motor resistor. To install, reverse removal
procedure.
BLOWER MOTOR SWITCH (REAR)
Removal & Installation (Durango)
Disconnect negative battery cable. Pry above indentations at
outer perimeter of rear blower motor switch. Pull rear blower motor
switch and disconnect electrical connector. Remove rear blower motor
switch. To install, reverse removal procedure.
COMPRESSOR
Removal & Installation
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
refrigerant lines and plug or cover all openings in A/C system.
2) Remove drive belt. Disconnect compressor electrical leads.
Remove compressor mounting nuts and bolts. Remove compressor. Drain
oil from compressor, and record amount of oil drained.
3) To install, reverse removal procedure. Using new
refrigerant oil, add to compressor the same amount of oil drained from
it. Evacuate and charge A/C system.
CONDENSER
NOTE: Before removing condenser, note location of radiator and
condenser air seals. If air seals are not installed properly,
A/C and engine cooling systems will not perform properly.
Removal
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
A/C fittings at inlet and outlet of condenser. Plug or cover all
openings in A/C system.
2) On Dakota, remove bolts securing radiator and fan shroud
to inside of upper radiator crossmember. Remove top mounting bolts
securing condenser to upper crossmember. Tilt top of radiator and fan
shroud toward engine.
3) On Ram Pickup (gasoline engine), remove bolts securing
condenser upper mounting brackets to outside of upper radiator
crossmember. Tilt condenser away from engine compartment far enough to
grasp top of condenser with both hands. On Ram Pickup (diesel engine),\
remove bolts securing condenser to charge air cooler. On all models,
lift condenser assembly from vehicle.
Installation
To install, reverse removal procedure. Install new "O" rings
to fittings. Fill cooling system. Evacuate and charge A/C system.
EVAPORATOR CORE & HEATER CORE
Removal & Installation (Dakota & Durango - Front)
Remove instrument panel. See INSTRUMENT PANEL. Remove A/C-
heater assembly. See A/C-HEATER ASSEMBLY. With A/C-heater housing
removed, remove housing cover. Remove evaporator core or heater core

from housing. To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system.
Removal & Installation (Durango - Rear Evaporator Core)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Remove
headliner from passenger compartment of vehicle. Remove sun visors and
sun visor arm supports.
2) Remove coat hooks, overhead assist handle and dome light.
If equipped, remove overhead console. Remove air outlet bezel from
rear A/C-heater assembly. Remove rear blower motor switch. Remove
upper liftgate opening trim. Disengage "A", "B", "C", and "D" pillar
trim as necessary to prevent trim panel interference.
3) Move second and third row seats to cargo position. Move
front seats to full recline position. Remove headliner fasteners.
Carefully bow headliner and remove through lift gate opening.
4) Disconnect "B" pillar drain hoses from "Y" fittings.
Disconnect "B" pillar refrigerant lines and plug or cover all openings
in A/C system. Remove lower A/C-heater assembly cover. Remove screws
securing refrigerant tube and retaining strap to right side of upper
housing cover. Remove evaporator core. To install, reverse removal
procedure. Install new "O" rings to A/C fittings. Evacuate and charge
A/C system.
Removal & Installation (Ram Pickup - Front)
1) Remove and disassemble A/C-heater housing. See
A/C-HEATER ASSEMBLY . Separate halves of A/C-heater housing and remove
top half. Remove evaporator or heater core from housing.
2) To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system. Fill cooling
system. On 5.9L diesel engine, engine is equipped with a one-way check
valve. DO NOT run engine while filling cooling system. Fill engine
with engine turned off.
INSTRUMENT PANEL
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. Disable air bag system.
See AIR BAG SYSTEM SAFETY article. Place front wheels in straight-
ahead position. Remove sill trim from both doorways. Remove kick panel
covers from both sides of vehicle. Remove mounting screws for hood
release handle.
2) Remove steering column trim panel and support bracket.
Remove tilt steering column lever (if equipped). Remove upper and
lower shrouds from steering column. Unplug driver's side air bag
module. Loosen multifunction switch wiring harness connector screw and
disconnect from switch. Screw will remain in connector.
3) Disconnect PRNDL cable. Disconnect shift cable from
steering column. Remove steering coupler lock pin. Remove toe plate
retaining screws. Remove steering column mounting bolts and remove
steering column from vehicle.
4) Remove screw from bulkhead wiring harness connector and
disconnect. Disconnect 2 body wiring harness connectors located next
to bulkhead connector. Disconnect 3 wiring harness connectors, from
junction block, located nearest to dash panel. Disconnect brake light
switch connector. Disconnect Rear Wheel Anti-Lock (RWAL) brake module
(if equipped), located near steering column support brackets.
5) Disconnect plastic retainer clip from parking brake
linkage rod, located at back of parking brake release handle. Remove
rod end from parking brake handle. Remove instrument panel center
support bracket. Unplug vacuum harness connector located at left end
of A/C-heater housing. Disconnect Air Bag Control Module (ACM)
connector.

foot wires to terminals of a 12-volt battery. After air bag module
deploys, let module cool off and allow dust to settle before
approaching.
POST-COLLISION INSPECTION
When a vehicle has been involved in a collision, certain
components of the passive restraint system must be inspected or
replaced. See PASSIVE RESTRAINT SYSTEM INSPECTION article in the
GENERAL INFORMATION section for post-collision inspection information.
REMOVAL & INSTALLATION
* PLEASE READ THIS FIRST *
WARNING: Failure to follow air bag service precautions may
result in air bag deployment and personal injury. See
SERVICE PRECAUTIONS . After component replacement,
ensure proper system operation. See SYSTEM OPERATION CHECK.
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may
exist until computer systems have completed a relearn cycle.
See COMPUTER RELEARN PROCEDURES in GENERAL INFORMATION
before disconnecting battery.
AIR BAG CONTROL MODULE (ACM)
WARNING: ACM contains impact sensor, which enables SRS to activate air
bag. To avoid accidental air bag deployment, DO NOT connect
ACM electrically to system unless it is bolted to vehicle.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Remove bottom
of center console (ACM trim cover).
2) On M/T models, remove center console from floor panel
transmission tunnel. On A/T models, remove screws securing trim cover
to ACM mounting bracket. See Fig. 2. Pull top of trim cover rearward
to release snap clips from instrument panel support bracket.
3) On all models, loosen but do not remove screws on sides
that secure instrument panel support bracket to ACM mounting bracket.
See Fig. 3 .
4) Remove nuts securing support bracket to studs on lower
instrument panel. Disconnect wire harness retainer from hole in
support bracket. Pull top of support bracket away from instrument
panel studs and fold down over ACM until it is laying on floor panel.
Unplug wire harness connector from ACM.
CAUTION: Always replace ACM and ACM mounting bracket as an assembly.
Replacement ACM includes a NEW mounting bracket. DO NOT mount
NEW ACM to old mounting bracket.
5) Remove screws securing mounting bracket to floor panel
transmission tunnel. Remove ACM, mounting bracket and support bracket
as a unit from floor panel.
Installation
To complete installation, reverse removal procedure. Install
ACM with arrow pointing toward front of vehicle. Connect ACM
connectors, ensuring connectors are locked into position. Tighten ACM

CAUTION: When removing a deployed air bag, wear eye protection, rubber
gloves and a long-sleeve shirt. Powder residue from air bag
deployment may irritate skin and eyes.
CAUTION: Before removing steering wheel, position front wheels in
straight-ahead position and lock steering column by removing
ignition key. Failure to do so could damage clockspring or
cause clockspring to be off-centered. DO NOT hammer on
steering wheel during removal, or collapsible column could be
damaged.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Air bag module
is mounted on face of steering wheel. Ensure wheels are pointed
straight-ahead and steering wheel is locked.
2) Remove air bag module-to-steering wheel screws from back
side of steering wheel. Lift air bag module and disconnect electrical
connectors from rear of module.
Installation
Connect air bag, cruise control and horn harness connectors
to rear of air bag module. Secure module to steering wheel. Tighten
air bag module-to-steering wheel screws to specification. See
TORQUE SPECIFICATIONS . DO NOT connect negative battery cable at this
time. Go to SYSTEM OPERATION CHECK .
PASSENGER-SIDE AIR BAG MODULE
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
3) Remove 3 screws securing instrument panel glove box
opening upper trim strip to instrument panel glove box opening upper
reinforcement, then remove trim strip. Remove 4 screws that secure 2
plastic support brackets of passenger-side air bag door panel outlet
housing to glove box opening upper reinforcement.
4) Reach through and above glove box opening to access and
disconnect air bag module harness connector. Remove 2 screws securing
passenger-side air bag module front bracket to instrument panel
structural support. Remove 3 screws securing passenger-side air bag
module rear bracket to glove box opening upper reinforcement.
5) Using trim stick, gently pry passenger-side air bag door
(starting at lower left edge) away from instrument panel top cover.
Remove air bag module, air bag door and panel outlet housing and
barrel assembly from instrument panel as a unit.
Installation
To install, reverse removal procedure. Ensure air bag door is
securely attached to instrument panel. Ensure air bag harness
connector latches fully engaged. DO NOT connect negative battery cable
at this time. Go to SYSTEM OPERATION CHECK .
CLOCKSPRING
CAUTION: Failure to position wheels in the straight-ahead position
with steering wheel locked when removing steering wheel could

5) Remove 3 screws securing passenger-side disable switch to
back of switch bezel and remove switch from bezel.
6) To install, reverse removal procedure. Tighten PAD switch
mounting screws to specification. See TORQUE SPECIFICATIONS. DO NOT
connect negative battery cable at this time. Go to
SYSTEM OPERATION CHECK .
Fig. 4: Identifying PAD Switch Connectors
Courtesy of DaimlerChrysler Corp.
ADJUSTMENTS


AN TI- T H EFT S YSTE M

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Anti-Theft Systems
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION
The Vehicle Theft Security System (VTSS) provides an engine
no-run feature, flashes headlights and sounds horn if any door or hood
is opened without using key or remote keyless entry transmitter, or if
battery cables are disconnected then reconnected when system is
activated.
Anti-theft system is controlled by Central Timer Module
(CTM). CTM is located under driver's side of dash panel, right of
steering column. If CTM is faulty, CTM cannot be repaired and must be
replaced.
VTSS is also equipped with a power-up mode. If battery is
disconnected or looses power while VTSS is armed, VTSS system remains
armed when power is restored. A temper alert signal is sounded on
vehicle entry if VTSS was triggered while away from vehicle. Horn will
sound 3 times alerting owner VTSS was triggered.
OPERATION
ARMING PROCEDURE (PASSIVE)
Remove key from ignition. Ensure headlights are off. Lock
doors while open, using power lock switch. Power lock switch will not
operate with key in ignition or headlights on while door is open.
Vehicle Theft Security System (VTSS) will not arm using key in lock
cylinder or mechanical lock button. While system is arming, SECURITY
light will flash rapidly for 15 seconds. Opening any door or turning
the ignition key while light is flashing will abort arming process.
Once arming process is complete, SECURITY light will go out.
ARMING PROCEDURE (ACTIVE)
Pressing Remote Keyless Entry (RKE) transmitter LOCK button
will actively arm Vehicle Theft Security System (VTSS). All doors must\
be closed and ignition switch in OFF position. While system is arming,
SECURITY light will flash rapidly for 15 seconds. Opening any door or
turning the ignition key while light is flashing will abort arming
process. Once arming process is complete, SECURITY light will go out.
DISARMING
Vehicle Theft Security System (VTSS) can be disarmed 2 ways:
unlock vehicle using key in any door and pressing remote keyless entry
transmitter UNLOCK button. If alarm has been set off, either method
can be used to disarm and shut-off horn.
CENTRAL TIMER MODULE (CTM)
Central Timer Module (CTM) is Vehicle Theft Security System
(VTSS) processor. CTM uses the data bus network to allow sharing and
reporting of sensor information. If a door ajar sensor is opened while
VTSS is set, a signal is sent to flash headlights and sound horn. PCM
is also notified through bus network to enable engine no-run feature.

CTM has remote keyless entry receiver and control logic incorporated.
COMPONENT TESTS
RELAYS
NOTE: Headlight relay may also be referred to as the security
relay. On Ram Pickup, the headlight relay is located in Power
Distribution Center (PDC) in engine compartment. On Ram Van
and Ram Wagon, the headlight relay is taped to headlight
switch harness. On Ram Pickup, the horn relay is located in
Power Distribution Center (PDC) in engine compartment. On Ram\
Van and Ram Wagon, the horn relay is located in junction
block under left side of instrument panel. For circuit
testing, see WIRING DIAGRAMS.
Headlight Relay & Horn Relay
Remove relay to be tested. Measure resistance between
appropriate relay terminals with relay de-energized and energized. See
RELAY TEST SPECIFICATIONS table. See Fig. 1. If continuity or
resistance is not as specified, replace relay.
RELAY TEST SPECIFICATIONS









\









\









\









\









\









\









\







Terminals Condition
De-Energized
87A & 30 .............................................. Continuity
87 & 30 ............................................ No Continuity
85 & 86 .................................... 70-80 Ohms Resistance
Energized ( 1)
87 & 30 ............................................... Continuity
87A & 30 ........................................... No Continuity
( 1) - Apply position battery voltage to terminal No. 85 and ground
terminal No. 86.









\









\









\









\









\









\









\







Fig. 1: Identifying Relay Connector Terminals
Courtesy of Chrysler Corp.
SYSTEM TESTS