1999 DODGE RAM lock

Fig. 2: Checking Differential Carrier Flange Runout
Courtesy of Chrysler Corp.
Cleaning & Inspection
Clean components with solvent and dry with compressed air.
Inspect components for wear. Inspect bearings and bearing races for
wear and pitting. Replace bearings and bearing races as a set. Inspect
ring gear and pinion teeth for wear and chipping, and replace as
matched set.
NOTE: Lubricate all bearings, bearing races, gears and thrust
washers with gear lube during reassembly.
Reassembly & Adjustments
1) Install side gear thrust washers on side gears. Install
side gears in differential carrier. Install pinion gear thrust washers
on pinion gears. Install pinion gears in differential carrier so gears
are positioned 180 degrees apart when meshed with side gears.
NOTE: If replacing side gears or side gear thrust washers, check
side gear clearance once differential carrier is installed in
axle housing. See FINAL INSPECTION & ASSEMBLY.
2) Rotate side gears until holes in pinion gears and thrust
washers align with pinion shaft hole in differential carrier. Install
pinion shaft. Ensure hole in pinion shaft is aligned with lock bolt

hole in differential carrier.
3) If ring gear and exciter ring (models with Rear Wheel
Anti-Lock brakes) were removed, slowly and evenly tap exciter ring
onto differential carrier. Ensure contact surface of ring gear and
differential carrier flange are clean and free of all nicks and burrs.
Remove any sharp areas from chamfer on inside diameter of ring gear.
4) Place ring gear into position on differential carrier.
Start 2 NEW ring gear bolts to align ring gear. Using brass drift and
hammer, alternately and evenly tap ring gear into position. Install
NEW ring gear bolts and tighten to specification. See TORQUE
SPECIFICATIONS.
NOTE: Use components from Pinion Gauge Set (C-3715-B) for 8 1/4"
ring gear, or (C-758-D6) for 9 1/4" ring gear) to complete
assembly. For proper component part number, see PINION GAUGE
SET COMPONENT APPLICATION table.
5) Install differential bearings on differential carrier (if
removed). Use appropriate bearing installer when installing
differential bearings. Go to PINION DEPTH.
PINION GAUGE SET COMPONENT APPLICATION









\









\









\









\









\









\









\







Component 8 1/4" 9 1/4"
Ring Gear Ring Gear
Part No. Part No.
Arbor ........................... SP-6029 ................ SP-6018
Gauge Block ..................... SP-5383 ................ SP-6020
Nut ............................. SP-3193 ................. SP-533
Shaft ........................... SP-5385 ................. SP-526
Sleeve "A" ...................... SP-5382 ................ SP-1730
Sleeve "B" ..................... SP-3194-B .............. SP-535-A
Spacer "A" ...................... SP-6030 ................ SP-6017
Spacer "B" ...................... SP-6022 ................ SP-6022
Washer ........................... SP-534 ................. SP-534









\









\









\









\









\









\









\







Pinion Depth
1) Using appropriate driver, install bearing races for pinion
bearings in axle housing (if removed). Assemble spacer "A" over shaft
followed by rear (pinion gear side) pinion bearing. See Fig. 3.
Install assembly into axle housing assembly.
2) Install sleeve "A" and front (pinion flange side) pinion
bearing on shaft. Install spacer "B", sleeve "B", washer and nut on
shaft. See Fig. 3. Using Holder (C-3281), hold sleeve "B" from
rotating and gradually tighten nut to seat pinion bearings.
NOTE: When tightening nut to seat pinion bearings, remove holder
and allow sleeve "B" to rotate several times during
tightening procedure to prevent damage to pinion bearings and
bearing cups.
3) Loosen nut. Lubricate pinion bearings with gear lube.
Retighten nut to 15-25 INCH lbs. (2-3 N.m). Rotate pinion several
times to fully seat pinion bearings.
4) Install gauge block and bolt on end of shaft. Using Allen
wrench, tighten bolt. Install arbor in axle housing. See Fig. 3.
Ensure arbor is centered in axle housing.
5) Place a piece of .002" (.05 mm) thick shim stock between
arbor and axle housing on each end of arbor. Install bearing caps over
arbor. Install and tighten bearing cap bolts to 120 INCH lbs. (14 N.
m). Using feeler gauge, check clearance between arbor and gauge block.

ring gear backlash will be checked with same teeth meshed. Rotate ring
gear to point of minimum ring gear backlash.
6) Loosen right adjuster (viewed from rear of axle housing)
and tighten left adjuster until ring gear backlash is .003-.004" (.08-
.10 mm) with each adjuster tightened to 120 INCH lbs. (14 N.m).
7) Rotate pinion back and forth 5-10 times to ensure proper
seating of differential bearings. Ensure ring gear backlash is still
as specified. Tighten bearing cap bolts to specification. See TORQUE
SPECIFICATIONS table.
8) Using adjuster rotator, tighten right adjuster to 75 ft.
lbs. (102 N.m). Rotate pinion back and forth 5-10 times to ensure
proper seating of differential bearings. Continue to tighten right
adjuster until torque remains constant at 75 ft. lbs. (102 N.m).
9) Recheck ring gear backlash at point of minimum ring gear
backlash. If ring gear backlash is not .005-.008" (.13-.20 mm),
increase torque on right adjuster, and seat differential bearings by
rotating pinion. Continue to tighten right adjuster until ring gear
backlash is correct.
10) Tighten left adjuster to 75 ft. lbs. (102 N.m). Rotate
pinion back and forth 5-10 times to ensure proper seating of
differential bearings. Continue to tighten left adjuster until torque
remains constant at 75 ft. lbs. (102 N.m).
11) Check ring gear backlash every 90 degrees to check ring
gear backlash variation. Ring gear backlash variation should not
exceed .003" (.08 mm). For example, if ring gear backlash is .005" (.\
15 mm) at minimum point, ring gear backlash should not exceed .008" (.\
20 mm) anywhere on ring gear.
12) With adjustments completed, install adjuster locks.
Ensure teeth on adjuster lock engages with hole in adjuster. Install
and tighten adjuster lock bolt to specification. See TORQUE
SPECIFICATIONS table.
FINAL INSPECTION & ASSEMBLY
1) With pinion bearing preload and ring gear backlash
properly adjusted, check gear tooth pattern contact. See GEAR TOOTH
CONTACT PATTERNS article in GENERAL INFORMATION.
2) To check side gear clearance, install axle shafts into
axle housing and side gears. Install clip on end of axle shaft. Pull
axle shaft outward, ensuring clip fully seats in counterbore on side
gear.
NOTE: If replacing side gears or side gear thrust washers, check
side gear clearance with axle shaft installed in axle
housing. Check side gear clearance on both side gears.
3) Install equal thickness feeler gauges on each side of side
gear, next to hub of side gear. See Fig. 4. This is side gear
clearance.
Fig. 4: Checking Side Gear Clearance
Courtesy of Chrysler Corp.
4) If no side gear clearance exists, proceed to step 8). If

Center Carrier Bearing Bolt ................................ 50 (68)\
Pinion Nut (Minimum Torque) .............................. 210 (285\
)
Ring Gear Bolt (1)
Dakota
8 1/4" ................................................. 75 (102)\
9 1/4" ................................................. 115 (157)\
Ram Pickup ............................................... 70 (95)\
Ram Van/Wagon ........................................... 75 (102)\
Shock Absorber Nut ......................................... 60 (81)\
"U" Bolt Nut
8 1/4" Ring Gear
Dakota 2WD .............................................. 65 (88)\
Dakota 4WD ............................................ 110 (149)\
9 1/4" Ring Gears
1/2" X 20 Bolt Thread ................................... 65 (88)\
9/16" X 18 Bolt Thread ................................ 110 (149)\
"U" Joint Strap Bolt
Diesel Models ............................................ 25 (34)\
Gasoline Models .......................................... 14 (19)\
Wheel Lug Nut
Dakota .......................................... 85-110 (115-149)\
Ram Pickup
5-Lug .......................................... 80-110 (108-149)\
8-Lug (Single Wheel) .......................... 120-150 (163-203\
)
8-Lug (Dual Wheel) ............................ 130-160 (176-217\
)
Ram Van/Wagon
1/2" Stud
60-Degree Cone ............................... 80-110 (108-149)\
90-Degree Cone ............................... 85-115 (115-156)\
5/8" Stud
90-Degree Cone .............................. 175-225 (237-305)\
Flanged Nut ................................. 300-350 (407-474)\
INCH Lbs. (N.m)
Adjuster Lock Bolt ......................................... 90 (10)\
Pinion Shaft Lock Bolt ( 2) ................................. 96 (11)
( 1) - Left-hand threaded bolts.
( 2) - Apply Loctite to bolt threads.









\









\









\









\









\









\









\

TESTING
NOTE: Trac-Lok differential can be tested without removing
differential case from axle housing.
1) Place blocks under both front wheels. Ensure engine is off
and transmission is in Neutral. Release parking brake. Raise one rear
wheel until it is completely clear of the floor. Remove wheel. Install
Adapter (6790) to wheel studs and tighten securely.
2) Using torque wrench on adapter, rotate axle and record
torque required. Repeat procedure for remaining rear wheel position.
If rotational torque for either rear wheel is less than 30 ft. lbs.
(40.1 N.m) or greater than 200 ft. lbs. (271 N.m), Trac-Lok unit mus\
t
be replaced or repaired.
REMOVAL & INSTALLATION
Servicing procedure is same as that used for standard
differential. See RBI FULL FLOATING AXLES article for servicing
procedures.
OVERHAUL
DIFFERENTIAL CARRIER
Disassembly
1) Place appropriate side gear holding tool in soft-jaw vise.
Position differential carrier on holding tool. Remove ring gear, if
necessary. Ring gear removal is only necessary when ring gear is being
replaced.
2) Remove roll pin holding pinion mate shaft into housing.
Remove pinion gear mate shaft. A drift and hammer can be used if
necessary. See Fig. 1.
3) Install appropriate Step Plate on lower side gear. Install
appropriate threaded forcing screw into upper side gear. See Fig. 2.
4) Thread Forcing Screw into threaded adapter disc until
forcing screw is centered in threaded adapter disc. Perform STEP 1
shown in illustration. See Fig. 2.
5) Place small screwdriver in slot of threaded adapter disc
to prevent disc from rotating. Tighten forcing screw to relieve
tension from clutch pack.
6) Remove pinion gear thrust washers. Loosen forcing screw to
release pressure from clutch pack. Install appropriate turning bar in
hole on side of differential case. Perform STEP 2 shown in
illustration. See Fig. 2.
7) Using turning bar, rotate differential case until pinion
gears can be removed. Remove pinion gears. Remove turning bar, forcing
screw, step plate, and threaded adapter disc from differential case.
8) Remove upper side gear and clutch pack. See Fig. 1. Remove
differential case from axle shaft. Remove remaining side gear and
clutch pack from differential case.
CAUTION: Mark clutch pack location for reassembly reference. Note
position of clutch pack components before removing clutch
pack retainers. Clutch packs must be assembled in correct
order and installed in original location.
9) Remove clutch pack retainers from clutch pack. Keeping
clutch pack components in correct order, disassemble clutch pack.

FLANGES
FLEX PLATES
FLUID LEVEL INDICATORS
FLUIDS AND LUBRICANTS
FLYWHEELS
FORCE MOTORS
GUIDES
HALF SHAFTS
HOSES, LINES AND TUBES
HOUSINGS (BELL, CASE, TAIL (EXTENSION) AND AUXILIARY)
INTERMEDIATE SHAFT SUPPORT BEARINGS
KEY INTERLOCK SYSTEMS
LIMITED SLIPS
LINES
LINKAGES (EXTERNAL)
LOCKING HUB ASSEMBLIES
LOCKING HUB CONTROL KNOBS
LUBRICANTS
METAL-CLAD SEALS
METALASTIC JOINTS
MODULATOR PINS
MODULATORS
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
ODOMETER DRIVES (MECHANICAL)
ODOMETER HEADS (MECHANICAL)
OIL PANS
PANS
PILOT HOLES
PRESSURE PLATES
PRESSURE SWITCHES
RACES
RUBBER JOINTS (METALASTIC)
SCREENS
SEALS
SEALS (METAL-CLAD)
SELECTOR INTERLOCK SYSTEMS
SERVOS
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
SENSORS
SIDE COVERS
SLIP YOKES
SOLENOIDS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEEDOMETER-DRIVEN GEAR HOUSINGS
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SWITCHES
TONE WHEELS
TOOTHED RINGS (TONE WHEELS)
TORQUE CONVERTERS
TRANSAXLE MOUNTS
TRANSDUCERS (TRANSMISSION)
TRANSMISSION COOLERS
TRANSMISSION MOUNTS
TRANSMISSION PANS
TRANSMISSION RANGE INDICATORS (PRNDL)
TUBES
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
VACUUM CONTROLS
VACUUM HOSES
VACUUM MOTORS
VACUUM-OPERATED SWITCHES

INTERMEDIATE SHAFT SUPPORT BEARINGS
INTERMEDIATE SHAFT SUPPORT BEARING INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bearing rollers, balls or
races are worn, pitted,
noisy, or feel rough when
rotated as an assembly . A .. Require replacement of bearing
assembly.
Bracket bent, affecting
performance ............ A .. Require repair or replacement.
Bracket bent, not
affecting performance .. .. ........ No service suggested or
required.
Bracket broken, affecting
performance ............ A ............ Require replacement.
Bracket broken, not
affecting performance .. .. ........ No service suggested or
required.
Bracket corroded,
affecting performance .. A .. Require repair or replacement.
Bracket corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Bracket cracked, affecting
performance ............ A .. Require repair or replacement.
Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performances) .......... .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Cracked ................. .. ........... Require replacement.
Rough (brinelling,
spalling) .............. A ............ Require replacement.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Seized .................. A ............ Require replacement.









\









\









\









\









\









\









\


KEY INTERLOCK SYSTEMS
See
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS) .
LIMITED SLIPS

See DIFFERENTIAL AND FINAL DRIVE ASSEMBLIES .
LINES
See HOSES, LINES AND TUBES .
LINKAGES (EXTERNAL)
LINKAGE (EXTERNAL) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Components missing ...... C .. Require replacement of missing
components.
Linkage bent, affecting
performance ............ A ... Require repair or replacement
of linkage.
Linkage bent, not
affecting performance .. 2 ... Suggest repair or replacement
of linkage.
Linkage binding, affecting
performance ............ A ... Require repair or replacement
of linkage.
Linkage binding, not
affecting performance .. 1 ... Suggest repair or replacement
of linkage.
Linkage broken .......... A ... Require repair or replacement
of linkage.
Linkage loose, affecting
performance ............ A ... Require repair or replacement
of linkage.
Linkage loose, not
affecting performance .. 1 ... Suggest repair or replacement
of linkage.
Linkage missing ......... C ............ Require replacement.
Linkage noisy ........... 2 .. Suggest repair or replacement.
Out of adjustment ....... B .. Require repair or replacement.
Worn to the extent that it
no longer performs its
intended function ...... A .. Require repair or replacement.









\









\









\









\









\









\









\


LOCKING HUB ASSEMBLIES
LOCKING HUB ASSEMBLY INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Inoperative ............. A ........... ( 1) Require repair or
replacement.
Loose ................... A .. Require repair or replacement.
Seized in any position .. A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation.









\









\









\









\









\









\









\


LOCKING HUB CONTROL KNOBS
LOCKING HUB CONTROL KNOB INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure