1999 DODGE RAM torque

block. Determine oil clearance. Clearance must be within
specification. See VALVE LIFTERS table under ENGINE SPECIFICATIONS.
Cylinder block can be bored for oversize lifters.
CYLINDER BLOCK ASSEMBLY
Piston & Rod Assembly
Install piston with notch or groove on top of piston toward
front of engine (timing chain end) with larger chamfer of connecting
rod bore toward crankshaft journal fillet.
Fitting Pistons
1) Measure piston diameter at top of piston skirt at 90-
degree angle to piston pin axis. Measure cylinder bore diameter below
top surface of cylinder bore, middle of bore and bottom of cylinder
bore.
NOTE: Piston diameter and cylinder bore should be measured at room
temperature of 70
F (21C).
2) Ensure piston diameter and clearance are within
specification. See PISTONS, PINS & RINGS table under ENGINE
SPECIFICATIONS.
Piston Rings
1) Ensure ring end gap and side clearances are within
specification. See PISTONS, PINS & RINGS table under ENGINE
SPECIFICATIONS.
2) Position piston ring gaps in proper location. See Fig. 16.
Compression ring gaps must be staggered so they do not align with oil
ring rail gap. Ensure identification marks (drill point, letter "O",
an oval depression or the word TOP) on compression rings face upward.
Fig. 16: Positioning Piston Rings
Courtesy of Chrysler Corp.
Rod Bearings
1) Crankshaft is marked to indicate undersize rod bearings.
See SPECIAL ENGINE MARKS. When replacing connecting rod bearings,
ensure connecting rod is installed with larger chamfer of connecting
rod bore toward crankshaft journal fillet.
2) Apply light coat of engine oil to connecting rod bolt
threads before tightening nut to specification. See TORQUE
SPECIFICATIONS table. Ensure oil clearance and side play are within
specification. See CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS table
under ENGINE SPECIFICATIONS.
Crankshaft & Main Bearings
1) Crankshaft is marked to indicate undersize main bearings.
See SPECIAL ENGINE MARKS. Main bearing cap location and direction of
installation should be marked before removal.

2) Ensure journal diameter, taper and out-of-round are within
specification. See CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS table
under ENGINE SPECIFICATIONS. Upper main bearings contain oil holes,
while lower bearings installed in main bearing cap do not.
3) Apply light coat of engine oil to threads before
tightening bolt to specification. See TORQUE SPECIFICATIONS table.
Ensure oil clearance and end play are within specification. See
CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS table.
CAUTION: Crankshaft journal grinding should not exceed .012" (.30 mm)
under standard size. DO NOT grind thrust surfaces of No. 3
main bearing. Final paper or cloth polishing after regrind
must be done in same direction as engine rotation.
Thrust Bearing
Thrust bearing is located on No. 3 main bearing. Replace
thrust bearing if crankshaft end play is not within specification. See
CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS table under ENGINE
SPECIFICATIONS.
NOTE: Cylinder bore should be measured at room temperature of 70
F
(21C).
Cylinder Block
1) Check cylinder bore, out-of-round and taper. Measure
cylinder bore diameter below top surface of cylinder bore, middle of
bore and bottom of cylinder bore. Bore cylinder block if bore diameter
is not within specification. See CYLINDER BLOCK table under ENGINE
SPECIFICATIONS.
NOTE: Cylinder block is marked to indicate oversize valve lifters.
See SPECIAL ENGINE MARKS.
2) Check valve lifter bore diameter. Check for scoring. If
scoring exists or lifter bore diameter is not within specification,
ream cylinder block bore for next oversize valve lifter. See VALVE
LIFTERS table under ENGINE SPECIFICATIONS.
ENGINE OILING
ENGINE LUBRICATION SYSTEM
System has a rotor-type oil pump and full-flow oil filter.
Oil is forced by pump through a series of oil passages in engine to
provide lubrication to engine components. Oil is supplied to rocker
assembly through hollow push rods. Push rods are fed oil from lifters.
See Fig. 17 .
Crankcase Capacity
On 3.9L, oil capacity with oil filter is 4.0 qts. (3.8L). On
5.2L and 5.9L, oil capacity with oil filter is 5.0 qts. (4.7L).
Oil Pressure
Oil pressure is 6 psi (.4 kg/cm
) at idle and 30-80 psi (2.1-
5.6 kg/cm) at 3000 RPM with engine at normal operating temperature.

OIL PUMP SPECIFICATIONS








\









\









\









\









\









\









\







Application Specification
Inner & Outer Rotor Thickness ................ .825" (20.96 mm) Min.\
Outer Rotor Diameter .......................... 2.47" (62.7 mm) Min.\
Outer Rotor-To-Pump Body Clearance ............. .014" (.36 mm) Max.\
Pump Cover Warpage ........................... .0015" (.038 mm) Max.\
Rotor End Clearance ................................. .004" (.10 mm)\
Rotor Tip Clearance ............................ .008" (.20 mm) Max.\
Spring Free Length ................................. 1.95" (49.5 mm)\
Spring Tension ......... 19.5-20.5 Lbs. @ 1.34" (8.8-9.3 kg @ 34 mm)\









\









\









\









\









\









\









\







CAUTION: Ensure oil pump fully engages with distributor drive shaft
before tightening bolt. It may be necessary to slightly
rotate oil pump during installation to align with distributor
drive shaft.
Reassembly & Installation
To reassemble, reverse disassembly procedure. Install NEW
relief valve retainer cap and oil seal ring. Tighten pump cover bolts.
Fill rotor cavity with engine oil before installing. To install,
reverse removal procedure.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Axle Bracket-To-Bellhousing Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Axle Shaft Nut
Dakota 4WD & Durango 4WD ............................... 180 (244)\
Axle Shaft-To-Differential Flange Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Axle-To-Insulator Bolt
Dakota 4WD & Durango 4WD ................................ 75 (102)\
Camshaft Sprocket Bolt ..................................... 50 (68)\
Camshaft Thrust Plate Bolt ................................. 18 (24)\
Clutch Housing-To-Cylinder Block Bolt
Dakota
(1) ..................................................... 30 (41)
( 2) ..................................................... 50 (68)
Ram Pickup
( 1)
3/8" Bolt ............................................ 33 (45)\
7/16" Bolt ........................................... 50 (68)\
( 2) ........................................................ N/A
Connecting Rod Bolt ........................................ 45 (61)\
Crankshaft Pulley Bolt ..................................... 18 (24)\
Cylinder Head Bolt ( 3)
Step 1 ................................................... 50 (68)\
Step 2 ................................................. 105 (142)\
Step 3 (Verify Torque) ................................. 105 (142\
)
Differential Pinion Nose Bracket-To-Adapter Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Differential Pinion Nose Bracket-To-Bellhousing Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Engine Mount Bracket-To-Frame Rail Bolt
Dakota 2WD & Durango 2WD ................................. 30 (41)\

Engine Mount Through-Bolt
Dakota 2WD & Durango 2WD ................................. 50 (68)\
Dakota 4WD, Durango 4WD & Ram Pickup .................... 75 (102)\
Grand Cherokee ............................................. 60 (81)\
Engine Mount-To-Cylinder Block Bolt
Dakota & Durango ......................................... 30 (41)\
Ram Pickup ............................................... 60 (81)\
Ram Van/Wagon & Grand Cherokee ............................. 65 (88)\
Engine Mount-To-Frame Bracket Bolt/Nut
Ram Pickup & Ram Van/Wagon .............................. 75 (102)\
Exhaust Manifold Bolt & Nut
Durango .................................................. 18 (24)\
All Others ................................................. 25 (34)\
Flywheel/Flexplate-To-Crankshaft Bolt ...................... 55 (75)\
Front Cover Bolt ........................................... 30 (41)\
Heat Shield Bolts .......................................... 30 (41)\
Main Bearing Cap Bolt ..................................... 85 (115)\
Oil Drain Plug ............................................. 25 (34)\
Oil Filter Adapter Stud .................................... 50 (68)\
Oil Pan Bolt ............................................... 18 (24)\
Oil Pump Bolt .............................................. 30 (41)\
Rocker Arm Bolt ............................................ 21 (28)\
Shift Motor Bolt
Dakota 4WD & Durango 4WD ................................. 65 (88)\
Spark Plug ................................................. 30 (41)\
Starter Bolts .............................................. 50 (68)\
Throttle Body Bolt ......................................... 17 (23)\
Transfer Case Yoke Bolt
Dakota 4WD & Durango 4WD ................................. 20 (27)\
Vibration Damper Bolt .................................... 135 (183)\
Water Pump Bolt ............................................ 30 (41)\
INCH Lbs. (N.m)
Intake Manifold Bolt ( 4)
Step 1 .................................................. 24 (2.7)\
Step 2 .................................................. 48 (5.4)\
Step 3 .................................................. 84 (9.5)\
Step 4 (Verify Torque All Bolts) ........................ 84 (9.5\
)
Intake Manifold Plenum Pan Bolt
Step 1 .................................................. 24 (2.7)\
Step 2 .................................................. 48 (5.4)\
Step 3 .................................................. 84 (9.5)\
Step 4 (Verify Torque) .................................. 84 (9.5\
)
Oil Pump Cover Bolt ........................................ 97 (11)\
Valve Cover Bolts .......................................... 95 (11)\
( 1) - Bolts through clutch housing into cylinder block.
( 2) - Bolts through cylinder block into clutch housing.
( 3) - Tighten bolts in sequence. See 7.
( 4) - Tighten bolts in sequence. See 5 and 6.









\









\









\









\









\









\









\







ENGINE SPECIFICATIONS
GENERAL SPECIFICATIONS (3.9L)








\









\









\









\









\









\









\







Application Specification
Displacement .................................... 239 Cu. In. (3.9L)\
Bore ............................................... 3.91" (99.3 mm)\
Stroke ............................................. 3.31" (84.1 mm)\

NOTE: Always refer to appropriate engine overhaul article in the
ENGINES section for complete overhaul procedures and
specifications for the vehicle being repaired.
REMOVAL
Remove intake and exhaust manifolds and valve cover. Cylinder
head and camshaft carrier bolts (if equipped), should be removed only
when the engine is cold. On many aluminum cylinder heads, removal
while hot will cause cylinder head warpage. Mark rocker arm or
overhead cam components for location.
Remove rocker arm components or overhead cam components.
Components must be installed in original location. Individual design
rocker arms may utilize shafts, ball-type pedestal mounts or no rocker
arms. For all design types, wire components together and identify
according to the corresponding valve. Remove cylinder head bolts.
Note length and location. Some applications require cylinder head
bolts be removed in proper sequence to prevent cylinder head damage.
See Fig. 1 . Remove cylinder head.
Fig. 1: Typical Cylinder Head Tightening or Loosening Sequence
This Graphic For General Information Only
INSTALLATION
Ensure all surfaces and head bolts are clean. Check that head
bolt holes of cylinder block are clean and dry to prevent block damage
when bolts are tightened. Clean threads with tap to ensure accurate
bolt torque.
Install head gasket on cylinder block. Some manufacturer's
may recommend sealant be applied to head gasket prior to installation.
Note that all holes are aligned. Some gasket applications may be
marked so certain area faces upward. Install cylinder head using care
not to damage head gasket. Ensure cylinder head is fully seated on
cylinder block.
Some applications require head bolts be coated with sealant
prior to installation. This is done if head bolts are exposed to water
passages. Some applications require head bolts be coated with light
coat of engine oil.

CYLINDER BLOCK
* PLEASE READ THIS FIRST *
NOTE: Always refer to appropriate engine overhaul article in the
ENGINES section for complete overhaul procedures and
specifications for the vehicle being repaired.
BLOCK CLEANING
Only cast cylinder blocks should be hot tank cleaned.
Aluminum cylinder blocks should be cleaned using cold tank method.
Cylinder block is cleaned in order to remove carbon deposits, gasket
residue and water jacket scale. Remove oil galley plugs, freeze plugs
and cam bearings prior to block cleaning.
BLOCK INSPECTION
Visually inspect the block. Check suspected areas for cracks
using the Dye Penetrant inspection method. Block may be checked for
cracks using the Magnaflux method.
Cracks are most commonly found at the bottom of the
cylinders, the main bearing saddles, near expansion plugs and between
the cylinders and water jackets. Inspect lifter bores for damage.
Inspect all head bolt holes for damaged threads. Threads should be
cleaned using tap to ensure proper head bolt torque. Consult machine
shop concerning possible welding and machining (if required).
CYLINDER BORE INSPECTION
Inspect the bore for scuffing or roughness. Cylinder bore
is dimensionally checked for out-of-round and taper using dial bore
gauge. For determining out-of-round, measure cylinder parallel and
perpendicular to the block centerline. Difference in the 2 readings
is the bore out-of-round. Cylinder bore must be checked at top, middle
and bottom of piston travel area.
Bore taper is obtained by measuring bore at the top and
bottom. If wear has exceeded allowable limits, block must be honed
or bored to next available oversize piston dimension.
CYLINDER HONING
Cylinder must be properly honed to allow new piston rings to
properly seat. Cross-hatching at correct angle and depth is critical
to lubrication of cylinder walls and pistons.
A flexible drive hone and power drill are commonly used.
Drive hone must be lubricated during operation. Mix equal parts of
kerosene and SAE 20w engine oil for lubrication.
Apply lubrication to cylinder wall. Operate cylinder hone
from top to bottom of cylinder using even strokes to produce 45 degree
cross-hatch pattern on the cylinder wall. DO NOT allow cylinder hone
to extend below cylinder during operation.
Recheck bore dimension after final honing. Wash cylinder
wall with hot soapy water to remove abrasive particles. Blow dry with
compressed air. Coat cleaned cylinder walls with lubricating oil.
DECK WARPAGE
Check deck for damage or warped head sealing surface. Place
a straightedge across gasket surface of the deck. Using feeler gauge,
measure clearance at center of straightedge. Measure across width and

SUPER CHARGERS
SWITCHES
THERMAL VACUUM VALVES
THERMOSTATIC AIR DOOR ASSEMBLIES
THERMOSTATS AND HOUSINGS
THROTTLE BODIES
THROTTLE CABLES
THROTTLE LINKAGES AND CABLES
THROTTLE POSITION SENSORS
THROTTLE POSITION SWITCHES
TIMING BELT SPROCKETS
TIMING BELTS
TORQUE STRUTS
TRANSMISSION RANGE SWITCHES
TUBE CLAMPS
TUBE CONNECTORS
TUBE COUPLERS
TUBES
TURBO CHARGERS
VACUUM CONNECTIONS
VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC)
VACUUM REGULATOR SOLENOIDS
VACUUM TUBES
VEHICLE SPEED SENSORS
VOLUME AIR FLOW SENSORS
WASTE GATE CONTROL SOLENOIDS
WASTE GATES AND BOOST CONTROL MECHANISMS
WATER PUMPS (ELECTRIC)
WATER PUMPS (NON-ELECTRIC)
WIRING HARNESSES AND CONNECTORS
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication

service intervals.
Missing ................. C ........ (3) Require replacement.
Noisy ................... 2 .......... ( 4) Further inspection
required.
See note below.
Plies separated ......... A ............ Require replacement.
Tension out of
specification .......... B ........... Require adjustment or
replacement.
Teeth missing ........... A ............ Require replacement.
( 1) - Inspect belt tensioners, pulleys, and cover.
( 2) - Determine cause of incorrect alignment and require repair.
( 3) - CAUTION: Internal engine damage may result from timing
belt damage/failure.
( 4) - Determine cause of noise and suggest repair.









\









\









\









\









\









\









\


TORQUE STRUTS
TORQUE STRUT INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding ................. A ............ Require replacement.
Body dented ............. A .......... ( 1) Further inspection
required.
Body punctured .......... A ............ Require replacement.
Bushing deteriorated,
affecting performance .. A ............ Require replacement.
Bushing deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Bushings missing ........ C ............ Require replacement.
Bushings separated from
mounting eye ........... 1 ............ Suggest replacement.
Damping (none) .......... A ............ Require replacement.
Leaking oil, enough for
fluid to be running down
the body ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Noisy ................... 2 .......... ( 2) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Seized .................. A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Require replacement of units where dents restrict strut
piston rod movement. If dents don't restrict movement, no
service is suggested or required.
( 2) - If noise is isolated to shock or strut, suggest replacement.