1999 DODGE RAM wheel size
[x] Cancel search: wheel sizePage 210 of 1691
AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS
1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85 C for 2 hours is generally considered a
maximum limit).
Page 346 of 1691
![DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
Condition Code](/manual-img/12/56915/w960_56915-345.png "DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
Condition Code")
\
\
\
\
\
\
\
Condition Code Procedure
Tire diameter incorrect,
affecting ABS or TCS ... A ............ Require replacement.
Tire pressure incorrect,
affecting ABS or TCS ... A .. Require repair or replacement.
Tire size incorrect,
affecting ABS or TCS ... A ............ Require replacement.
\
\
\
\
\
\
\
TOOTHED RINGS (TONE WHEEL)
NOTE: Copied from Drivetrain UIGs.
If the toothed ring requires replacement and cannot be
replaced as a separate component, replace the assembly of which the
ring is a part.
TOOTHED RING INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Alignment incorrect ..... B ............... Require repair or
replacement.
Bent .................... B ............ Require replacement.
Contaminated, affecting
performance ............. A ........ Require repair. Identify
and correct cause.
Cracked ................. B ............ Require replacement.
Loose ................... A ............. Require replacement
of worn parts.
Missing ................. C ............ Require replacement.
Number of teeth
incorrect .............. B ............ Require replacement.
Teeth broken ............ A ............ Require replacement.
Teeth damaged, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
VACUUM BOOSTERS
VACUUM BOOSTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Applies too much assist
(oversensitive) ........ A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Auxiliary vacuum pump
inoperative ............ A ........... ( 1) Require repair or
replacement.
Check valve grommet
deteriorated, affecting
performance ............ A .. Require replacement of grommet.
Page 350 of 1691
to the conditions that follow, you may suggest rebuilding or
replacement of the other wheel cylinder (on the same axle) for
preventive maintenance, for example, the part is close to the end of
its useful life.
Determine the need to rebuild or replace based upon the
individual wheel cylinder conditions that follow.
WHEEL CYLINDER INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ..... Require replacement of bent
parts.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
parts.
Attaching hardware
loose .................. A .. Require repair or replacement.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bleeder port damaged (if
non-repairable) ........ A ............ Require replacement.
Bleeder screw broken off
in wheel cylinder (if non-
repairable) ............ A ........ (1) Require replacement.
Bleeder screw plugged ... A ........... ( 1) Require repair or
replacement of bleeder screw.
Bleeder screw seized .... A ........ ( 2) Require replacement.
Bore corroded (pitted) .. B ............ Require replacement.
Bore grooved ............ A ............ Require replacement.
Bore oversized .......... B ............ Require replacement.
Dust boot missing ....... C ..... Require replacement of dust
boot.
Dust boot torn .......... A . ( 3) Require replacement of dust
boot.
Leaking ................. A ....... ( 4) Require rebuilding or
replacement.
Piston corroded, affecting
performance ............ B ... Require replacement of piston
and rebuilding or replacement
of wheel cylinder.
Piston finish worn off .. B ... Require replacement of piston
and rebuilding or replacement
of wheel cylinder.
Piston stuck in bore .... A .... Require replacement of wheel
cylinder.
Loose ................... B .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Only required if the hydraulic system must be opened.
( 2) - Seized is defined as bleeder screw that cannot be removed
after a practical attempt at removing. Only required if
the hydraulic system must be opened.
Page 420 of 1691
DRIV E A XLE S - P O W ER -L O K
1999 D odge P ic ku p R 1500
1998-99 DRIVE AXLES
CHRY - Power-Lok
Ram Pickup
IDENTIFICATION
POWER-LOK DIFFERENTIAL APPLICATION \
\
\
\
\
\
\
Application Axle Ring Axle
Model Gear Size Ratio
Ram Pickup ........ Rear Axle ... 10.5" (266.7 mm) ..... 267 RBI\
\
\
\
\
\
\
\
NOTE: For rear axles with limited-slip differentials, see TRAC-LOK
article.
DESCRIPTION & OPERATION
A Rear Beam-Design Iron (RBI) axle is an iron casting axle
and differential housing with axle shaft tubes extending from either
side. Tubes are pressed to form a one-piece full-floating axle
housing.
Power-Lok differential assembly is optional equipment. The
differential assembly is a limited-slip type differential. It is
similar in operation to a conventional type differential, except for 2
clutch packs located at the side gears in the differential case. See
Fig. 1 . Clutch packs provide differential action when required for
turning corners, and transmit equal torque to both wheels when driving
straight ahead.
AXLE RATIO & IDENTIFICATION
Axle ratio can be identified by axle identification tag
attached to axle housing cover. See AXLE RATIO SPECIFICATIONS table.
AXLE RATIO SPECIFICATIONS
\
\
\
\
\
\
\
Application Ratio
Ram Pickup ......................................... 3.54:1 & 4.10:1
\
\
\
\
\
\
\
WARNING: Whenever rotating wheels, DO NOT use engine to rotate
individual wheels unless both rear wheels are off ground and
vehicle is securely supported.
LUBRICATION
CAPACITY
DRIVE AXLE CAPACITY ( 1) \
\
\
\
\
\
\
Application Pts. (L)\
Ram Pickup ........................................... ( 2) 7.0 (3.3)
Page 424 of 1691
DRIV E A XLE - R BI F U LL F LO ATIN G A XLE
1999 D odge P ic ku p R 1500
1998-99 DRIVE AXLES
CHRY - RBI Full-Floating Axles
Ram Pickup, Ram Van/Wagon
IDENTIFICATION
REAR DRIVE AXLE APPLICATION \
\
\
\
\
\
\
Application Axle Ring Axle
Model Gear Size Ratio
Ram Pickup ....... 248 RBI .......... 9.75" ... 3.55:1 Or 4.10:1
Ram Pickup ....... 267 RBI ......... 10.50" ... 3.54:1 Or 4.10:1
Ram Pickup ....... 286 RBI ......... 11.00" ... 3.54:1 Or 4.10:1
Ram Van/Wagon .... 248 RBI .......... 9.75" ... 3.55:1 Or 4.10:1
\
\
\
\
\
\
\
DESCRIPTION & OPERATION
The Rear Beam-Design Iron (RBI) axle is an iron center
casting (differential housing) with axle shaft tubes extending from
both sides. The tubes are pressed in to form a one-piece axle housing.
Axle contains an integral carrier with hypoid-type ring gear
and pinion with a solid full-floating axle shaft splined into side
gear. Vehicle weight is supported on tubes of axle housing. Axle
shafts may be serviced without disturbing wheel bearings. On vehicles
equipped with Rear Wheel Anti-Lock (RWAL) brakes, a brake sensor is
mounted on top of axle housing and an exciter ring is mounted on ring
gear.
Axles may be equipped with limited-slip differential. Models
248 and 286 RBI use a Trac-Lok differential and Model 267 RBI uses a
Power-Lok differential as optional equipment. Trac-Lok differential
uses a one-piece case. Power-Lok differential uses a 2-piece case.
Both differentials use same internal components as a standard
differential, except 2 clutch packs are used in the differential case.
NOTE: For servicing of limited-slip differential components in
differential case, see appropriate POWER-LOK or TRAC-LOK
article.
AXLE RATIO & IDENTIFICATION
NOTE: Axle ratio can be identified by axle identification tag
attached to axle housing cover. For axle ratio, see REAR
DRIVE AXLE APPLICATION table at beginning of article.
LUBRICATION
CAPACITY
DRIVE AXLE CAPACITY ( 1) \
\
\
\
\
\
\
Application Pts. (L)\
Ram Pickup
248 RBI ................................................ 6.3 (3.0)\
Page 451 of 1691
DRIV E A XLE - T R AC -L O K
1999 D odge P ic ku p R 1500
1998-99 DRIVE AXLES
CHRY - Trac-Lok
Dakota, Ram Pickup, Ram Van/Wagon
IDENTIFICATION
TRAC-LOK DIFFERENTIAL APPLICATION (REAR AXLE) \
\
\
\
\
\
\
Model Ring Gear Axle
Size Model
Dakota .................... 8 1/4" ........................... ( 1)
Ram Pickup ............ 9 3/4" ....................... 248 RBI
10 3/4" ....................... 267 RBI
11" ....................... 286 RBI
Ram Van/Wagon ............. 9 3/4" ....................... 248 RBI
( 1) - Manufacturer does not designate axle model.
\
\
\
\
\
\
\
NOTE: For rear axles with limited-slip differentials, see POWER-LOK
- RAM PICKUP article.
DESCRIPTION & OPERATION
A Rear Beam-Design Iron (RBI) axle is an iron casting axle
and differential housing with axle shaft tubes extending from either
side. Tubes are pressed in to form a one-piece full-floating axle
housing.
Trac-Lok differential assembly is optional equipment. The
Trac-Lok differential assembly is a limited-slip type differential. It
is similar in operation to a conventional type differential, except
for 2 clutch packs located at the side gears in the differential case.
See Fig. 1 . Clutch packs provide differential action when required for
turning corners, and transmit equal torque to both wheels when driving
straight ahead.
AXLE RATIO & IDENTIFICATION
Axle ratio can be identified by axle identification tag
attached to axle housing cover. See AXLE RATIO SPECIFICATIONS table.
AXLE RATIO SPECIFICATIONS
\
\
\
\
\
\
\
Application Ratio
Dakota ..................................... 3.21:1, 3.55:1 & 3.92:1
Ram Pickup
248 RBI .......................................... 3.55:1 & 4.10:1
267 & 286 RBI .................................... 3.54:1 & 4.10:1
Ram Van/Wagon ...................................... 3.55:1 & 4.10:1
\
\
\
\
\
\
\
WARNING: Whenever rotating wheels, DO NOT use engine to rotate wheels
unless both rear wheels are off the ground and vehicle is
securely supported.
Page 458 of 1691
Apply multipurpose lubricant (NLGI grade 2 EP) to "U" joints
and slip joint fittings.
INSPECTION
Abnormal vibration and noise can come from many driveline
sources. Drive shaft vibration/noise increases with vehicle speed
(MPH). A vibration that occurs within a specific speed is not caused
by drive shaft imbalance. Before overhauling driveline, check for
other causes/sources of possible vibration/noise.
TIRES & WHEELS
Check tire inflation and wheel balance. Check for foreign
objects in tread, damaged tread, mismatched tread patterns or
incorrect tire sizes. Check for bent wheels.
CENTER BEARING
Tighten drive shaft center bearing mounting bolts. If bearing
insulator is deteriorated or oil-soaked, or drive shaft can be moved
up/down in support, replace center bearing support assembly.
ENGINE & TRANSMISSION MOUNTS
Tighten mounting bolts. If rubber mounts are deteriorated or
broken, replace as needed.
DRIVE SHAFT(S)
Check drive shaft(s) for missing weights, broken welds, or
for dents affecting balance. Check for undercoating, mud, snow/ice on
drive shaft(s). Clean shafts thoroughly and test drive.
"U" JOINTS
Check for foreign material lodged in joints and flange/yokes.
Check for loose "U" joint-to-flange mounting bolts. Check for worn "U"
joint needle bearings. Check for Reddish-Brown rust-dust around "U"
joint caps. Replace "U" joints if necessary.
ADJUSTMENTS
CHECKING DRIVE SHAFT PHASING
One-Piece Drive Shafts
1) Ensure "U" joint flanges on either end of drive shaft are
in same plane. See Fig. 2. Drive shafts with slip joints between yokes
often have arrows to aid in alignment. If yokes are not in same plane,
disassemble slip joint from drive shaft splines. Install slip joint
back onto drive shaft splines, aligning "U" joint yokes. Test drive.
2) Single tube type drive shaft has slip joint on outside of
"U" joint yoke (at transmission end). If one-piece tube type drive
shaft yokes are out of alignment, the drive shaft is torque-twisted.
Drive shaft must be replaced.
Page 870 of 1691
MAIN TE N AN CE IN FO RM ATIO N
1999 D odge P ic ku p R 1500
1997-99 MAINTENANCE
Chrysler Motors Maintenance Information
Dodge: Ram Pickup R1500
Ram Pickup R2500
Ram Pickup R3500
* PLEASE READ THIS FIRST *
Before preforming maintenance on vehicle, ensure that all
cautions and warnings have been observed to prevent vehicle damage or
personal injury. See CAUTIONS & WARNINGS.
NOTE: For scheduled maintenance intervals and the related fluid
capacities, fluid specifications and labor times for major
service intervals, see SCHEDULED SERVICES article below:
R1500
* SCHEDULED SERVICES - NORMAL SERVICE (GAS)
* SCHEDULED SERVICES - SEVERE SERVICE (GAS)
* SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)
* SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)
R2500
* SCHEDULED SERVICES - NORMAL SERVICE (GAS)
* SCHEDULED SERVICES - SEVERE SERVICE (GAS)
* SCHEDULED SERVICES - NORMAL SERVICE (GAS - MD)
* SCHEDULED SERVICES - SEVERE SERVICE (GAS - MD)
* SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)
* SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)
R3500
* SCHEDULED SERVICES - NORMAL SERVICE (GAS - MD)
* SCHEDULED SERVICES - SEVERE SERVICE (GAS - MD)
* SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)
* SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)
Warranty information and specifications for fluid
capacities, lubrication specifications, wheel and tire size,
and battery type are covered in this article.
MODEL IDENTIFICATION
VIN LOCATION
The Vehicle Identification Number (VIN) is located on the
left side of the dash panel at the base of the windshield. The VIN
chart explains the code characters.
VIN CODE ID EXPLANATION