1998 TOYOTA LAND CRUISER engine

AT110-01
D12667
Lock Washer
- AUTOMATIC TRANSMISSIONPARK/NEUTRAL POSITION (PNP) SWITCH
AT-7
1861 Author
: Date
:
2004 LAND CRUISER (RM1071U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON-VEHICLE REPAIR
1. REMOVE ENGINE NO. 2 UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Pry off the lock washer and remove the nut.
(b) Remove the bolt and park/neutral position switch.
4. INSTALL PARK/NEUTRAL POSITION SWITCH
(a) Install the park/neutral position switch with the bolt.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)
(b) Install a new lock washer and the nut.
Torque: 6.9 N´m (70 kgf´cm, 62 in.´lbf)
(c) Bent the claws on the lock washer to stake the nut.
(d) Adjust the park/neutral position switch
(See page DI-361).
5. CONNECT PARK/NEUTRAL POSITION SWITCH CON-
NECTOR
6. INSTALL ENGINE NO. 2 UNDER COVER

AT111-02
D13663
AT0103
D12703
D12704
Bolt
- AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
AT-8
1862 Author
: Date
:
VALVE BODY ASSEMBLY
ON-VEHICLE REPAIR
1. REMOVE ENGINE NO.2 UNDER COVER
2. DRAIN ATF
3. REMOVE OIL PAN
NOTICE:
Some fluid will remain in the oil pan.
(a) Remove the 20 bolts.
(b) Remove the oil pan gasket.
4. EXAMINE PARTICLES IN PAN
Remove the magnets and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and
on the magnets to anticipate the type of wear you will find in the
transmission.
Steel (magnetic)...bearing, gear and clutch plate wear
Brass (non-magnetic)...bushing wear
5. REMOVE OIL STRAINER
Remove the 4 bolts, the oil strainer and the O-ring.
NOTICE:
Be careful as some fluid will come out with the oil strainer.
6. DISCONNECT TEMPERATURE SENSOR
(a) Disconnect the 7 solenoid connectors.
(b) Remove 2 bolts and the 2 temperature sensors clamp
from the valve body.
(c) Disconnect the 2 temperature sensor from the valve body.
7. DISCONNECT 7 CONNECTORS FROM SHIFT SOLE-
NOID VALVES

- AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
AT-1 1
1865 Author
: Date
:
16. FILL ATF AND CHECK ATF LEVEL
(a) Install a new gasket and a drain plug.
Torque: 20 N´m (204 kgf´cm, 15 ft´lbf)
(b) Remove the refill plug.
(c) Fill new fluid through the refill hole (See page AT-3-1).
17. INSTALL ENGINE NO.2 UNDER COVER

BE0GD-23
I25523
Cowl SIde J/B RH

RADIO Fuse
TweeterRadio Assembly
Ignition Switch
Engine Room R/B

AMP Fuse
Woofer SpeakersSpeakers
Power Amplifier Steering Pad Switch
RSA
Antenna Assembly

Motor Antenna
Cowl Side J/B LH

ECU IG1 Fuse

IG Fuse
BE-170
- BODY ELECTRICALAUDIO SYSTEM
2543 Author
: Date
:
2004 LAND CRUISER (RM1071U)
LOCATION

Physical address: 190 Radio receiver assembly
Diagnosis item
ROM Error
Absence of
MasterDiagnosis contentCountermeasure and
inspected parts
Error is detected in internal ROM. Logical address
01
(Communication
Control)
01 *2
(Communication
Control)Component in which this code is re-
corded has been disconnected from
system with ignition in ACC or ON.
Or, when this code was recorded, ra-
dio receiver assembly was discon-
nected.
Check harness for power supply
system of radio receiver assembly.

Check harness for communica-
tion system of radio receiver as-
sembly.
DTC
21
D6Replace radio receiver assembly.
RAM Error Error is detected in internal RAM. 01
(Communication
Control)22Replace radio receiver assembly.
No Response
to Connection
Check 01 *3
(Communication
Control)Component shown by auxiliary code
is or had been disconnected from
system after engine start.
D9
Check harness for power supply
system of component shown by
auxiliary code.

Check harness for communica-
tion system of component shown by
auxiliary code. D8
Last Mode Error 01 *2
(Communication
Control)Component operated (sounds and/
or images were provided) before en-
gine stop is or has been discon-
nected with ignition switch in ACC or
ON.
Check harness for power supply
system of component shown by
auxiliary code.

Check harness for communica-
tion system of component shown by
auxiliary code. D9
No Response
to ON/OFF
InstructionNo response is identified when
changing mode (audio and visual
mode change). Detected when
sound and picture does not change
by button operation. DA 01
(Communication
Control)
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.

If error occurs again, replace
component shown by auxiliary
code.
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Mode Status
Error DB 01 *2
(Communication
Control)Dual alarm is detected.
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.
- BODY ELECTRICALAUDIO SYSTEM
BE-141
2514 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3. DIAGNOSIS CODE LIST
w/ Navigation system (See page)

Transmission
Error DC 01 *4
(Communication
Control)Transmission to component shown
by auxiliary code has been failed.
(Detecting this DTC does not nec-
essary mean actual failure.)
If same auxiliary code is recorded
in other component, check harness
for power supply and communica-
tion system of components shown
sub code.
Master Reset
(Momentary
Interruption) DD 01 *3
(Communication
Control)After engine is started, radio receiv-
er assembly assembly was discon-
nected from system.
If this error occurs frequently, re-
place radio receiver assembly.
Slave Reset
(Momentary
Interruption) DE 01 *3
(Communication
Control)After engine is started, slave com-
ponent was disconnected from sys-
tem.
Check harness for power supply
of component shown by auxiliary
code.

Check harness for communica-
tion system of component shown by
auxiliary code.
Master Error DF 01 *4
(Communication
Control)Due to defective condition of radio
receiver assembly, master function
is switched to audio equipment.
Error occurs in communication be-
tween sub-master (audio) and ra-
dio receiver assembly.
Check harness for power supply
of radio receiver assembly.

Check harness for communica-
tion system of radio receiver as-
sembly .

Check harness for communica-
tion system between radio receiver
assembly and sub-master compo-
nent.
Registration
Completion
Instruction
Error E0 01
(Communication
Control)ºRegistration Completion Instruc-
tionº command from radio receiver
assembly cannot be received.
Since this DTC is provided for en-
gineering purpose, it may be de-
tected when no actual failure exists.
Audio
processor ON
error E1
01 *2
(Communication
Control)While source equipment is operat-
ing, AMP output is stopped.
Check harness for power supply
of radio receiver assembly.

Check harness for communica-
tion system of radio receiver as-
sembly.
ON/OFF
Instruction
Parameter
Error E2 01
(Communication
Control)Error occurs in ON/OFF controlling
command from radio receiver as-
sembly assembly.
Replace radio receiver assembly
.
Registration
Request
Transmission E3 01
(Communication
Control)Registration Request command is
output from slave component.
Receiving Connection Check
Instruction, Registration Request
command is output from sub-mas-
ter component.
Since this DTC is provided for en-
gineering purpose, it may be de-
tected when no actual failure exists.
Plural Frame
Abort E4 01
(Communication
Control)
Since this DTC is provided for en-
gineering purpose, it may be de-
tected when no actual failure exists. Plural frame transmission is
aborted.
AM Tuner Error 43 60
(Radio receiver
assembly)Replace radio receiver assembly. Abnormal condition is detected in
AM tuner.
Inspect radio receiver assembly.
FM Tuner Error 44
60
(Radio receiver
assembly)Replace radio receiver assembly. Abnormal condition is detected in
FM tuner.
BE-142
- BODY ELECTRICALAUDIO SYSTEM
2515 Author
: Date
:
2004 LAND CRUISER (RM1071U)

EJECT
Malfunction 41 61
(Cassette
switch)Malfunction due to mechanical fail-
ure.Replace radio receiver assembly.
63 (In-dash CD
auto changer)42 No Disc
ReadoutDisc cannot be read. Inspect CD.
63 (In-dash CD
auto changer)44
CD Error
Error is detected in CD auto
changer.Replace radio receiver assembly.
Physical address: 440 Strereo component amplifier
01
(Communica-
tion Control)22 RAM Error
01
(Communica-
tion Control)D6
*1Absence of
MasterComponent in which this code is re-
corded has been disconnected from
system with ignition in ACC or ON.
Or, when this code was recorded, ra-
dio receiver assembly was discon-
nected.
Check harness for power supply of
radio receiver assembly.

Check harness for communication
system of radio receiver assembly.

Check harness for power supply of
stereo component amplifier.

Check harness for communication
system of stereo component ampli-
fier. HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Logical addressDTC
Diagnosis itemDiagnosis content
Countermeasure and inspeced parts
01
(Communica-
tion Control)21 ROM Error Abnormal condition of ROM is
detected.Replace stereo component
amplifier.
Abnormal condition of RAM is
detected.Replace stereo component
amplifier.
63
(In-dash CD auto
Changer)45EJECT Error
CD cannot be ejected.
Replace radio receiver assembly.
63
(In-dash CD auto
Changer)47 CD High Temp.
High temperature is detected in
CD auto changer.Replace radio receiver assembly.
63
(In-dash CD auto
Changer)48CD Excess
CurrentExcess current is applied to CD
auto changer.Replace radio receiver assembly.
Mechanical or
Media Error 40 61
(Cassette
switch)Inspect cassette tape. Malfunction due to mechanical fail-
ure is identified. Or, cassette tape is
cut or entangled.
- BODY ELECTRICALAUDIO SYSTEM
BE-143
2516 Author
: Date
:
2004 LAND CRUISER (RM1071U)

01*6
(Communica-
tion Control)D7 Connection
Check ErrorComponent in which this code is re-
corded has been disconnected from
system after engine start.
Or, when this code was recorded,
radio receiver assembly was dis-
connected.
Check harness for power supply of
radio receiver assembly.

Check harness for communication
system of radio receiver assembly.

Check harness for power supply of
stereo component amplifier.

Check harness for communication
system of stereo component ampli-
fier.
Transmission
Error DC
*2 01
(Communication
Control)Transmission to component shown
by auxiliary code has bee failed.
(This code does not necessarily
mean actual failure.)If same auxiliary code is recorded in
other component(s), check harness
for power supply and communica-
tion system of components shown
sub code.
Master Reset
(Momentary
Interruption) DD
*3 01
(Communication
Control)
Check harness for power supply
of radio receiver assembly.

Check harness for communica-
tion system of radio receiver as-
sembly.

If error occurs frequently, replace
radio receiver assembly.
Registration
Completion
Instruction
Error E0
*1 01
(Communication
Control)ºRegistration Completion Instruc-
tionº command fromradio receiver
assembly cannot be received.Since this DTC is provided for engi-
neering, it may be detected when
no actual failure exists.
ON/OFF
Instruction
Parameter
Error E2 01
(Communication
Control)Error is detected in ON/OFF control
command from radio receiver as-
sembly.Replace radio receiver assembly.
Registration
Request
Transmission E3 01
(Communication
Control)Since this DTC is provided for engi-
neering, it may be detected when
no actual failure exists.
Registration Request command
is output from slave component.

By reception of connection check
Instruction, Registration Request
command is output from sub-mas-
ter component.After engine is started, radio receiv-
er assembly assembly was discon-
nected from system.
Master Error DF
*4 01
(Communication
Control)Due to defective condition of com-
ponent with a display, master func-
tion is switched to audio equip-
ment . Error occurs in communica-
tion between sub-master (audio)
and master component.
Check harness for power supply
of radio receiver assembly.

Check harness for communica-
tion system of radio receiver as-
sembly.

Check harness for communica-
tion system between radio receiver
assembly and sub-master compo-
nent.
Audio proces-
sor ON error E1
*1 01
(Communication
Control)While source equipment is operat-
ing, AMP output is stopped.
Check harness for power supply of
radio receiver assembly

Check harness for communication
system of radio receiver assembly.
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists. BE-144
- BODY ELECTRICALAUDIO SYSTEM
2517 Author
: Date
:
2004 LAND CRUISER (RM1071U)