1998 TOYOTA LAND CRUISER fuses

BE1367
Medium Current Fuse and High Current Fuse
Equal Amperage Rating
V00076
Abbreviation Part Name Symbol Illustration
FUSE
MEDIUM CURRENT FUSE
HIGH CURRENT FUSE
FUSIBLE LINK
CIRCUIT BREAKERFUSE
M-FUSE
H-FUSE
FL
CB
- INTRODUCTIONREPAIR INSTRUCTIONS
IN-5
5 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(3) Precoated parts are indicated in the component il-
lustrations by the º
º symbol.
(g) When necessary, use a sealer on gaskets to prevent
leaks.
(h) Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
(i) Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found in Preparation section in this
manual.
(j) When replacing fuses, be sure the new fuse has the cor-
rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.

BE1367
Medium Current Fuse and High Current Fuse
Equal Amperage Rating
V00076
Abbreviation Part Name Symbol Illustration
FUSE
MEDIUM CURRENT FUSE
HIGH CURRENT FUSE
FUSIBLE LINK
CIRCUIT BREAKERFUSE
M-FUSE
H-FUSE
FL
CB
- INTRODUCTIONREPAIR INSTRUCTIONS
IN-5
5 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(3) Precoated parts are indicated in the component il-
lustrations by the º
º symbol.
(g) When necessary, use a sealer on gaskets to prevent
leaks.
(h) Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
(i) Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found in Preparation section in this
manual.
(j) When replacing fuses, be sure the new fuse has the cor-
rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.

A07061
TOYOTA
Hand-Held
Tester
DLC3SF10V-02
B04440
Up
Pulsation
Damper
Screw
B04441
SST
(Gauge)SST
(Adaptor)
SST
(Union)
Front Fuel Pipe
Gasket
- SFIFUEL PUMP
SF-7
1706 Author
: Date
:
2004 LAND CRUISER (RM1071U)
FUEL PUMP
ON-VEHICLE INSPECTION
1. CHECK FUEL PUMP OPERATION
(a) Connect a TOYOTA hand-held tester or OBD II scan tool
to the DLC3.
(b) Turn the ignition switch ON, and press the TOYOTA
hand-held tester or OBD II scan tool main switch ON.
NOTICE:
Do not start the engine.
(c) Select the ACTIVE TEST mode on the TOYOTA hand-
held tester or OBD II scan tool.
(d) Please refer to the TOYOTA hand-held tester or OBD II
scan tool operator's manual for further details.
(e) If you have no TOYOTA hand-held tester or OBD II scan
tool, connect the positive (+) and negative (-) leads from
the battery to the fuel pump connector. (See step 3)
(f) Disconnect the fuel return hose from the clamp on the V-
bank cover.
(g) Remove the 2 bolts, nuts and V-bank cover.
(h) Check that the pulsation damper screw pop up when the
fuel pump operates.
If operation is not as specified, check following parts:

Fusible link

Fuses

EFI main relay

Fuel pump

ECM

Wiring connections
(i) Turn the ignition switch OFF.
(j) Disconnect the TOYOTA hand-held tester or OBD II scan
tool from the DLC3.
2. CHECK FUEL PRESSURE
(a) Check the battery positive voltage is above 12 V.
(b) Disconnect the negative (-) terminal cable from the bat-
tery.
(c) Remove the front fuel pipe from the LH delivery pipe (See
page SF-22).
(d) Install the front fuel pipe and SST (pressure gauge) to the
delivery pipe with the 3 lower gaskets and SST (adaptor).
SST 09268-45014 (09268-41190, 90405-06167)
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(e) Wipe off any splattered gasoline.
(f) Reconnect the negative (-) terminal cable to the battery.
(g) Connect a TOYOTA hand-held tester or OBD II scan tool
to the DLC3 (See (a) to (e) in step 1 on the check fuel
pump operation).
(h) Measure the fuel pressure.