Page 383 of 3115
H04821
: Clip
H21409
H04754
H04755
BO-10
- BODYFRONT DOOR
2584 Author: Date:
2004 LAND CRUISER (RM1071U)
6. REMOVE DOOR TRIM
(a) Remove the 2 caps and the 7 screws.
(b) Remove the 3 clips.
(c) Insert a screwdriver between the door and the door trim
to pry the trim.
NOTICE:
Be careful not to damage the door and the door trim.
HINT:
Tape up the screwdriver tip before use.
(d) Pull the trim upward to remove it.
7. REMOVE INSIDE HANDLE
(a) Remove the screw and the inside handle.
(b) Disconnect the 2 control cables from the inside handle as
shown in the illustration.
8. REMOVE TWEETER SPEAKER
Disconnect the connector, then remove the bolt and the tweeter
speaker.
9. REMOVE OUTSIDE REAR VIEW MIRROR
Disconnect the connector, then remove the 3 bolts and the out-
side rear view mirror.
10. REMOVE SERVICE HOLE COVER
(a) Remove the clamps and the wire harness.
(b) Remove the service hole cover.
NOTICE:
Do not tear the cover.
HINT:
At the time of reassembly, pull out the 2 control cables and wire
harness through the service hole cover.
11. REMOVE DOOR BELT MOULDING
(a) Remove the screw.
(b) Using a scraper, remove the door belt moulding.
HINT:
Tape up the scraper tip before use.
12. REMOVE DOOR GLASS
(a) Open the door glass until the bolts appear in the service
hole.
(b) Remove the 2 bolts and the door glass.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
NOTICE:
Do not damage the door glass.
HINT:
Pull the glass upward to remove it.
13. REMOVE SPEAKER
Remove the 3 screws and the speaker, then disconnect the
connector.
14. REMOVE DOOR GLASS RUN
15. REMOVE LOWER FRAME
Remove the bolt and the lower frame.
Page 386 of 3115
BO1KT-04
H18928
Headrest
Headrest Support
Seatback Board
Lumber Support Seatback Frame
Seatback Pad Armrest
Seat Cushion Cover
Seat Cushion Pad
Seat Cushion Frame
Seat Cushion
Inner Shield
Front Seat Inner BeltReclining Adjuster Inside Shield
Lower Seat Cushion Shield
Seat Cushion
Outer Shield
Power Seat
Switch Knob Power Seat SwitchLumber Support Switch
Front Seat
Cushion ShieldSeat Position Control Relay Seatback Cover Hog Ring
Hog Ring
: Specified torqueN´m (kgf´cm, ft´lbf)
Non-reusable part
Seat HeaterSeat Heater
Seat WireSeat Wire
Seat Adjuster Assembly
w/ Side Airbag:
Side Airbag Assembly
37 (380, 27)
21 (210, 15)
21 (210, 15)
43 (440, 32)
21 (210, 15)
42 (430, 31)
8.0 (82, 71 in.´lbf)
Seat Position Sensor Driver's Side:
42 (430, 31)
42 (430, 31)
42 (430, 31)
Armrest Cap
Armrest Bush
Spacer
4.7 (48, 42 in.´lbf)
w/ Side Airbag:
5.5 (56, 49 in.´lbf)
5.5 (56, 49 in.´lbf)
42 (430, 31)
43 (440, 32)
BO-104
- BODYFRONT SEAT
2678 Author: Date:
2004 LAND CRUISER (RM1071U)
FRONT SEAT
COMPONENTS
Page 388 of 3115
H03735
H03736
H04737
H04738
H20959
- BODYFRONT SEAT
BO-107
2681 Author: Date:
2004 LAND CRUISER (RM1071U)
4. REMOVE FRONT SEAT INNER BELT
(a) Remove the clamp, then disconnect the connector.
(b) Remove the bolt and the inner belt.
5. REMOVE SEAT CUSHION INNER SHIELD
Remove the 3 screws and the seat cushion inner shield.
6. REMOVE LOWER SEAT CUSHION SHIELD
Remove the screw and the lower seat cushion shield as shown
in the illustration.
7. REMOVE FRONT SEAT CUSHION SHIELD
Remove the screw and the front seat cushion shield.
8. REMOVE SEAT CUSHION ASSEMBLY
(a) Remove the 4 bolts.
(b) Remove the clamps from the seat cushion assembly.
9. REMOVE SEAT CUSHION FRAME
(a) Disengage the hook.
(b) Remove the hog rings and the seat cushion frame from
the seat cushion cover with pad.
10. REMOVE SEAT CUSHION COVER (See page BO-1 10)
11. IF NECESSARY, REPLACE SEAT CUSHION HEATER
(See page BO-1 10)
Page 394 of 3115
H04738
H04737
H03736
H03735
H03733
BO-1 16
- BODYFRONT SEAT
2690 Author: Date:
2004 LAND CRUISER (RM1071U)
13. INSTALL FRONT SEAT CUSHION SHIELD
Install the seat cushion shield with the screw.
14. INSTALL LOWER SEAT CUSHION SHIELD
Install the seat cushion shield with the screw.
15. INSTALL SEAT CUSHION INNER SHIELD
Install the seat cushion inner shield with the 3 screws.
16. INSTALL FRONT SEAT INNER BELT
(a) Engage the clamp, then connect the connector.
(b) Install the inner belt with the bolt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
17. INSTALL SEAT CUSHION OUTER SHIELD
(a) Install the power seat switch with the 3 screws.
(b) Install the lumber support switch with the 2 screws.
(c) Connect the connectors as shown in the illustration.
(d) Install the seat cushion outer shield with the 4 screws.
(e) Install the power seat switch knobs.
18. INSTALL SEATBACK BOARD
Page 432 of 3115
BO1LD-03
H18905
Rear Door Opening TrimRoof Headlining Rear Trim
Upper Roof Side
Inner Garnish
Quarter Trim Jack CoverStriker Plate
Quarter Trim Panel Rear Door Scuff PlateQuarter Belt MouldingRear Mat
Rear Mat Set Plate Quarter Window
GlassStriker Plate Quarter Window
Glass Weatherstrip
Striker Plate
x5 Rear
Assist Grip Rear Vent Window Motor
Assist Grip
Plug
Assist Grip
Plug
- BODYQUARTER WINDOW GLASS
BO-61
2635 Author: Date:
2004 LAND CRUISER (RM1071U)
QUARTER WINDOW GLASS
COMPONENTS
Page 434 of 3115
BO4IW-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips BO-62
- BODYQUARTER WINDOW GLASS
2636 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATE
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATE
9. REMOVE REAR DOOR OPENING TRIM
10. REMOVE QUARTER TRIM PANEL
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel, then disconnect the con-
nector.
11. REMOVE REAR NO. 2 SEAT OUTER BELT SHOUL-
DER ANCHOR
12. REMOVE REAR NO. 1 SEAT OUTER BELT SHOUL-
DER ANCHOR
Page 435 of 3115
H18906
: 9 Clips
H04108
H05403
Quarter Belt
Moulding
Clip
: 4 Clips
H04110
- BODYQUARTER WINDOW GLASS
BO-63
2637 Author: Date:
2004 LAND CRUISER (RM1071U)
13. REMOVE UPPER ROOF SIDE INNER GARNISH
(a) Using a screwdriver, remove the assist grip plugs, then re-
move the 2 screws and the rear assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, remove the upper roof side inner gar-
nish.
HINT:
Tape the screwdriver tip before use.
14. REMOVE QUARTER WINDOW GLASS
(a) Disconnect the connector.
(b) w/ Antenna:
Disconnect the connector.
(c) Remove the 2 bolts, the 2 nuts and the quarter window
glass.
15. REMOVE QUARTER WINDOW GLASS WEATH-
ERSTRIP
16. REMOVE QUARTER BELT MOULDING
(a) Remove the screw.
(b) Using a screwdriver, remove the quarter belt moulding.
HINT:
Tape up the screwdriver tip before use.
17. REMOVE REAR VENT WINDOW MOTOR
Remove the screw and the rear vent window motor.
18. REMOVE QUARTER WINDOW LOCK
Remove the screw and the quarter window lock.
Page 441 of 3115
BO1JE-03
H20973
Quarter Window Glass
with WeatherstripDivision Bar
Door Glass Run
Door Glass Door Belt Moulding
Service Hole Cover
Door Inside
Handle Bezel No. 1Inside Handle
Power Window
Switch Door Lock Outside Handle
Window Regulator
Door Courtesy Light
Door TrimDoor CheckDoor Hinge
Speaker
Door Hinge
: Specified torque
N´m (kgf´cm, ft´lbf)
Precoated part
27 (275, 20)
26 (265, 19)
5.0 (51, 44 in.´lbf)
8.0 (82, 71 in.´lbf)
26 (265, 19)
8.0 (82, 71 in.´lbf)
Door Inside
Handle Bezel No. 2
Door Check
Cover
23 (235, 17)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
8.0 (82, 71 in.´lbf)
23 (235, 17)
BO-14
- BODYREAR DOOR
2588 Author: Date:
2004 LAND CRUISER (RM1071U)
REAR DOOR
COMPONENTS
