1998 TOYOTA LAND CRUISER airbag

H05265
: 4 Clips
H21424
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
H21425
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
- BODYROOF HEADLINING
BO-99
2673 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Using a screwdriver, remove the center pillar lower gar-
nish as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
(c) Use the same manner described above to the other side.
21. REMOVE CENTER PILLAR GARNISH
(a) Using a screwdriver, remove the seat belt anchor cover
cap.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the bolt and the front seat outer belt shoulder an-
chor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(c) Using a clip remover, remove the clip.
(d) Using a screwdriver, remove the center pillar garnish.
HINT:
Tape up the screwdriver tip before use.
(e) Use the same manner described above to the other side.
22. REMOVE SUN VISOR
(a) Using a screwdriver, remove the caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the screws, then disconnect the connectors.
(c) Remove the sun visors.
23. REMOVE DOUBLE VISOR
Remove the screws and the double visors.
24. REMOVE HOLDER
Remove the screws and the holders.

H05268
H05270
H21423
4 Clips
H18926
BO-100
- BODYROOF HEADLINING
2674 Author
: Date
:
2004 LAND CRUISER (RM1071U)
25. REMOVE DOME LIGHT
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the dome light, then disconnect
the connector.
26. REMOVE MAP LAMP
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the map lamp, then disconnect
the connector.
27. REMOVE OVERHEAD CONSOLE BOX
(a) Remove the bolt.
(b) Using a screwdriver, remove the overhead console box,
then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
28. REMOVE REAR A/C CONTROL PANEL
Using a screwdriver, release the 4 claws and pull out the rear
A/C control panel, then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
29. REMOVE ROOM TEMPERATURE SENSOR
Using a scrwedriver, pull out the room temperature sensor, then
disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
30. REMOVE ASSIST GRIPS
31. w/o Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS
32. REMOVE ROOF HEADLINING
Using a clip remover, remove the 3 clips and the roof headlining.
33. REMOVE REAR A/C REGISTER
34. w/ Curtain Shield Airbag:
REMOVE ADJUSTABLE ANCHOR
Remove the 2 bolts and the adjustable anchor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
35. w/ Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS

BO1LL-02
AB0152
SST BO-144
- BODYSEAT BELT PRETENSIONER
2718 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISPOSAL
HINT:
When scrapping vehicle equipped with an SRS or disposing of
a front seat outer belt (with seat belt pretensioner), always first
deploy the airbag in accordance with the procedure given in RS
section or activate the seat belt pretensioner. If any abnormality
occurs with the airbag deployment or seat belt pretensioner ac-
tivation, contact the SERVICE DEPT. of TOYOTA MOTORS
SALES, U.S.A., INC.. When disposing of a front seat outer belt
(with seat belt pretensioner) activated in a collision, follow the
same procedure given in step 1-(d) in ºDISPOSALº.
CAUTION:

Never dispose of front seat outer belt which has inac-
tivated pretensioner.

The seat belt pretensioner produces a sizeable ex-
ploding sound when it activates, so perform the op-
eration out-of-door and where it will not create a nui-
sance to nearby residents.

When activating the seat belt pretensioner, always
use the specified SST. (SRS Airbag Deployment Tool)
Perform the operation in a place away from electrical
noise.
SST 09082-00700, 09082-00740

When activating a front seat outer belt (with seat belt
pretensioner), perform the operation at least 10 m (33
ft) away from the front seat outer belt.

Use gloves and safety glasses when handling a front
seat outer belt with activated pretensioner.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a front seat outer belt with
activated pretensioner.

AB0158
SSTBattery
AB0152
SST
AB0158
SSTBattery
H01580
SST
- BODYSEAT BELT PRETENSIONER
BO-145
2719 Author
: Date
:
2004 LAND CRUISER (RM1071U)
1. SEAT BELT PRETENSIONER ACTIVATION WHEN
SCRAPPING VEHICLE
HINT:
Have a battery ready as the power source to activate the seat
belt pretensioner.
(a) Check functioning of SST.
CAUTION:
When activating the seat belt pretensioner, always use the
specified SST: SRS Airbag Deployment Tool.
SST 09082-00700, 09082-00740
(1) Connect the SST to battery.
Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip to the battery neg-
ative (-) terminal.
HINT:
Do not connect the yellow connector which will be connected
with the seat belt pretensioner.
(2) Check functioning of SST.
Press the SST activation switch, and check the LED
of the SST activation switch lights up.
CAUTION:
If the LED lights up when the activation switch is not being
pressed, SST malfunction is probable, so definitely do not
use the SST.
(b) Disconnect the pretensioner connector.
(1) Remove the front door scuff plate.
(2) Remove the front door opening trim.
(3) Remove the rear door scuff plate.
(4) Remove the rear door opening trim.
(5) Remove the center pillar lower garnish.

BO0RW-09
- BODYSRS AIRBAG
BO-3
2577 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SRS AIRBAG
PRECAUTION
The LAND CRUISER is equipped with SRS (Supplemental Restraint System) such as the driver airbag and
the front passenger airbag. (The side airbag and the curtain shield airbag are optional.) Failure to carry out
service operation in the correct sequence could cause the SRS to unexpectedly deploy during the servicing,
possibly leading to a serious accident. Before servicing (including removal or installation of parts, inspection
or replacement), be sure to read the precautionary notices in the RS section.

HANDLING PRECAUTIONS ON RELATED COMPONENTS
1. FOR VEHICLES EQUIPPED WITH SRS AIRBAG AND SEAT BELT PRETENSIONER
The TOYOTA LAND CRUISER is equipped with an SRS (Supplemental Restraint System), such as the driver
airbag and front passenger airbag and seat belt pretensioners. Failure to carry out service operations in the
correct sequence could cause the supplemental restraint system to unexpectedly deploy during servicing, pos-
sibly leading to a serious accident. Further, if a mistake is made in servicing the supplemental restraint system,
it is possible the SRS may fail to operate when required. Before servicing (including removal or installation of
parts, inspection or replacement), be sure to read the following items carefully, then follow the correct proce-
dure described in this manual.

Malfunction symptoms of the supplemental restraint system are difficult to confirm, so the diagnostic
trouble codes become the most important source of information when troubleshooting.
When troubleshooting the supplemental restraint system, always inspect the diagnostic trouble codes
before disconnecting the battery.

Work must be started after 90 seconds from the time the ignition switch is turned to the ºLOCKº position
and the negative (-) terminal cable is disconnected from the battery.
(The supplemental restraint system is equipped with a back-up power source so that if work is started
within 90 seconds of disconnecting the negative (-) terminal cable from the battery, the SRS may
deploy.)
When the negative (-) terminal cable is disconnected from the battery, memory of the clock and audio
systems will be cancelled. So before starting work, make a record of the contents memorized by the
audio memory system.
Then when work is finished, reset the clock and audio systems as before.
To avoid erasing the memory of each memory system, never use a back-up power supply from outside
the vehicle.

Even in cases of a minor collision where the SRS does not deploy, the passenger's airbag assembly,
the steering wheel pad and seat belt pretensioners should be inspected.
Never use SRS parts from another vehicle. When replacing parts, replace them with new parts.

Before repairs, remove the airbag sensor if shocks are likely to be applied to the sensor during repairs.

Never disassemble and repair the airbag sensor assembly, steering wheel pad in order to reuse it.

If the airbag sensor assembly, steering wheel pad have been dropped, or if there are cracks, dents or
other defects in the case, bracket or connector, replace them with new ones.

Do not expose the airbag sensor assembly, steering wheel pad directly to hot air or flames.

Use a volt/ohmmeter with high impedance (10 k
/V minimum) for troubleshooting of the electrical cir-
cuit.

Information labels are attached to the periphery of the SRS components. Follow the instructions on the
notices.

After work on the supplemental restraint system is completed, check the SRS warning light.

Before repairing the body, remove the SRS parts if, during repair, shocks are likely to be applied to the
sensors due to vibrations of the body or direct tapping with tools or other parts.

Do not expose the SRS parts directly to hot air or flames.
NOTICE:
1) The maximum ambient temperature tolerance is 120
°C (248°F) for the front airbag sensor, 105°C
(221
°F) for the center airbag sensor assembly and 93°C (200°F) for the steering wheel pad, and
front passenger airbag assembly. If it is possible that the ambient temperature may reach or ex-
ceed the temperature limit, remove the sensors and the steering wheel pad from the vehicle or
protect them with a hot insulation material before staring work.
2) Prior to welding, remove adjacent SRS parts form the vehicle or protect them with fire-proof cov-
ers.

If the vehicle is damaged, visually inspect for damage to the steering wheel pad using the inspection
procedures described in section RS of the repair manual for the relevant model year.
INTRODUCTIONIN-6

STEERING WHEEL PAD (with Airbag)

When removing the steering wheel pad or handling a new steering wheel pad, it should be placed
with the pad top surface facing up.
In this case, the twin-lock type connector lock lever should be in the locked state and care should be
taken to place it so the connector will not be damaged. In addition do not store a steering wheel pad
on top of another one. Storing the pad with its metallic surface up may lead to a serious accident if
the airbag inflates for some reason.

Never measure the resistance of the airbag squib. (This may cause the airbag to deploy, which is
very dangerous.)

Grease should not be applied to the steering wheel pad and-the pad should not be cleaned with de-
tergents of any kind.

Store the steering wheel pad where the ambient temperature remains below 93°C (200°F), without
high humidity and away from electrical noise.

When using electric welding, first disconnect the airbag connector (yellow color and 2 pins) under the
steering column near the combination switch connector before starting work.

When disposing of a vehicle or the steering wheel pad alone, the airbag should be deployed using
an SST before disposal.
Carry out the operation in a safe place away from electrical noise.
FRONT PASSENGER AIRBAG ASSEMBLY

Always store a removed or new front passenger airbag assembly with the airbag deployment direc-
tion facing up. Storing the airbag assembly with the airbag deployment direction facing down could
cause a serious accident if the airbag inflates.

Never measure the resistance of the airbag squib.
(This may cause the airbag deploy, which is very dangerous.)

Grease should not be applied to the front passenger airbag assembly and the airbag door should not
be cleaned with detergents of any kind.

Store the airbag assembly where the ambient temperature remains below 93°C (200°F), without
high humidity and away from electrical noise.

When using electric welding, first disconnect the airbag connector (yellow color and 2 pins) installed
on the glove compartment finish plate at the left side of the glove compartment before starting work.

When disposing of a vehicle or the airbag assembly alone, the airbag should be deployed using an
SST before disposal.
Perform the operation in a safe place away from electrical noise.
SEAT BELT PRETENSIONER

Before doing any operation which will apply a strong shock to the vehicle, or before removing the
seat belt pretensioner, be sure to apply the sensor shock.

Never disassemble the seat belt pretensioner.

Do not subject the seat belt pretensioner to shocks or bring magnets close to it.

Do not expose the seat belt pretensioner to high temperature or fire.

Do not drop the seat belt pretensioner. Never use a seat belt pretensioner which has been dropped.

Never install the seat belt pretensioner in another vehicle.

Store removed seat belt pretensioners on a flat, stable surface.

After frontal collision, always check whether the seat belt pretensioners have been activated.

When disposing of a vehicle or the pretensioner by itself, always activate the pretensioner before
disposal.

The seat belt pretensioner is hot when activated, so let it cool down fully before you dispose of it.
Never apply water to the seat belt pretensioner.
INTRODUCTIONIN-7

Component to be alignedSection of repair manual for
relevant model
Front WheelsSuspension and Axle (SA) section
Rear WheelsSuspension and Axle (SA) section
Plopeller ShaftPropeller Shaft (PR) section
AIRBAG SENSOR ASSEMBLY

Never reuse the airbag sensor assembly involved in a collision when the SRS has deployed.

The connectors to the airbag sensor assembly should be connected or disconnected with the sensor
mounted on the floor. If the connectors are connected or disconnected while the airbag sensor as-
sembly is not mounted to the floor, it could cause undesired ignition of the supplemental restraint sys-
tem.

Work must be started after 90 seconds from the time the ignition switch is turned to the ºLOCKº posi-
tion and the negative (-) terminal cable is disconnected from the battery, even if only loosening the
set bolts of the airbag sensor assembly.
WIRE HARNESS AND CONNECTOR

The SRS wire harness is integrated with the cowl wire harness assembly and floor wire harness as-
sembly. The wires for the SRS wire harness are encased in a yellow corrugated tube. All the connec-
tors for the system are also a standard yellow color. If the SRS wire harness becomes disconnected
or the connector becomes broken due to an accident, etc., repair or replace it as shown on page.
2. BRAKE SYSTEM
The brake system is one of the most important safety components. Always follow the directions and
notes given in section BR of the repair manual for the relevant model year when handling brake sys-
tem parts.
NOTICE: When repairing the brake master cylinder or TRAC system, bleed the air out of the TRAC
system.
3. DRIVE TRAIN AND CHASSIS
The drive train and chassis are components that can have great effects on the running performance
and vibration resistance of the vehicle. After installing components in the sections listed in the table
below, perform alignments to ensure correct mounting angles and dimensions. Particularly accurate
repair of the body must also be done to ensure correct alignment.
HINT: Correct procedures and special tools are required for alignment. Always follow the directions
given in the repair manual for the relevant model during alignment and section Dl of this manual.
4. COMPONENTS ADJACENT TO THE BODY PANELS
Various types of component parts are mounted directly on or adjacently to the body panels. Strictly ob-
serve the following precautions to prevent damaging these components and the body panels during
handling.

Before repairing the body panels, remove their components or apply protective covers over the com-
ponents.

Before prying components off using a screwdriver or a scraper, etc., attach protective tape to the tool
tip or blade to prevent damaging the components and the body paint.

Before removing components from the outer surface of the body, attach protective tape to the body
to ensure no damage to painted areas.
HINT: Apply touch-up paint to any damaged paint surfaces.

Before drilling or cutting sections, make sure that there are no wires, etc. on the reverse side.
INTRODUCTIONIN-8