Page 2476 of 3115

MA02Q-01
MA-2
- MAINTENANCEINSIDE VEHICLE
50 Author: Date:
2004 LAND CRUISER (RM1071U)
INSIDE VEHICLE
GENERAL MAINTENANCE
These are the maintenance and inspection items which are considered to be owner's responsibility. They
can be done by the owner or be can have them done at a service shop. These items include those which
should be checked on a daily basis, those which, in most cases, do not require (special) tools and those
which are considered to be reasonable for the owner to do. Items and procedures for general maintenance
are as follows.
1. GENERAL NOTES
Maintenance items may very from country and country. Check the owner's manual supplement in
which the maintenance schedule is shown.
Every service items in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same time interval as before un-
less otherwise noted.
Failure to do even one item an cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlights aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner at defroster
mode.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and mounted securely.
10. STEELING WHEEL
Check that it has the specified freeplay. Be alert for changes in steering condition, such as hard steering,
excessive freeplay or strange noises.
11. SEATS
(a) Check that all front seat controls such as seat adjusters, seatback recliner, etc. operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latch position.
(d) For folding-down rear seat backs, check that the latches look securely.
12. SEAT BELTS
(a) Check that the seat belt system such as buckles, retractors and anchors operate properly and smooth-
ly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.
Page 2688 of 3115

RS0BO-08
H20940
- SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
RS-73
2348 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.
Never reuse the airbag sensor assembly involved in
a collision when the airbag has deployed.
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 6, refer to page BO-91.
1. INSTALL AIRBAG SENSOR ASSEMBLY
(a) Install the airbag sensor assembly with the 3 bolts.
Torque: 17.5 N´m (178 kgf´cm, 13 ft´lbf)
(b) Connect the airbag sensor connectors.
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure the sensor assembly is installed with the
specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installing, shake the sensor assembly to check
that there is no looseness.
2. INSTALL CENTER LOWER INSTRUMENT CLUSTER
FINISH PANEL ASSEMBLY
3. INSTALL FRONT CONSOLE BOX
4. INSTALL REAR CONSOLE BOX WITH CONSOLE
REAR END PANEL
5. INSTALL UPPER CONSOLE PANEL
6. INSTALL TRANSFER SHIFT LEVER KNOB
7. INSTALL FRONT SEAT (See page BO-1 17)
8. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2699 of 3115

RS0TH-03
H20929
(1)(3)
(2)(3)
(3) RS-68
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2343 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use airbag parts from another vehicle. When replac-
ing parts, replace them with new parts.
1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
(a) In the order shown in the illustration, install the curtain
shield airbag with the 8 bolts.
Torque: 9.8 N´m (100 kgf´cm, 86 in.´lbf)
CAUTION:
Pay due attention not to twist the deployment section of the
curtain shield airbag assembly.
NOTICE:
Make sure that the curtain shield airbag assembly is
installed to the specified torque.
If the curtain shield airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the curtain shield
airbag assembly with a new one.
When installing the curtain shield airbag assembly,
take care it is not pinched between other parts.
(b) Connect the connector of the curtain shield airbag as-
sembly.
2. INSTALL ROOF HEADLINING (See page BO-101)
3. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2704 of 3115

RS0SL-04
H20948
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
RS-89
2364 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the curtain shield airbag sensor assem-
bly involved in a collision when the airbag has
deployed.
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 8, refer to page BO-101.
1. INSTALL CURTAIN SHIELD AIRBAG SENSOR AS-
SEMBLY
(a) Install the curtain shield airbag sensor assembly with the
2 bolts.
Torque: 17.5 N´m (178 kgf´cm, 13 ft´lbf)
(b) Connect the connector.
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure that the sensor assembly is installed with
the specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL QUARTER TRIM PANEL
3. INSTALL STRIKER PLATES
4. INSTALL REAR NO. 2 SEAT
5. INSTALL REAR MAT SET PLATE
6. INSTALL REAR SEAT BELT ANCHOR
7. INSTALL REAR DOOR OPENING TRIM
8. INSTALL REAR DOOR SCUFF PLATE
9. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2709 of 3115

RS0BT-06
H20944
LH:
RH:
Front
Front RS-78
- SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
2353 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.
Never reuse the sensor involved in a collision when
the SRS has deployed.
Never repair a sensor in order to reuse it.
1. INSTALL FRONT AIRBAG SENSOR
(a) Install the front airbag sensor with the arrow on the sensor
facing toward the front of the vehicle.
Torque: 7.5 N´m (76 kgf´cm, 66 in.´lbf)
NOTICE:
Make sure that the sensor is installed with the speci-
fied torque.
If the sensor has been dropped, or there are cracks,
dents or other defects in the case, brackets or con-
nector, replace the removed sensor with a new one.
The front sensor is equipped with an electrical con-
nection check mechanism. Be sure to lock this mech-
anism securely when connecting the connector. If the
connector is not securely locked, a malfunction code
will be detected by the diagnostic system.
(b) Connect the front airbag sensor connector.
2. INSTALL BATTERY AND BATTERY CARRIER
3. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2722 of 3115
H21422
RS-42
- SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
2317 Author: Date:
2004 LAND CRUISER (RM1071U)
7. CONNECT AIRBAG CONNECTOR
(a) Connect the airbag connector.
(b) Set the connector on the No. 1 under cover.
(c) Install the No. 1 under cover to the lower No. 2 finish pan-
el.
(d) Install the glove compartment door (See page BO-91).
8. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2744 of 3115
RS-84- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
2359 Author: Date:
2004 LAND CRUISER (RM1071U)
6. INSTALL FRONT SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 42 N´m (428 kgf´cm, 31 ft´lbf)
7. INSTALL LAP BELT OUTER ANCHOR COVER
8. INSTALL FRONT DOOR SCUFF PLATE
9. INSTALL REAR DOOR SCUFF PLATE
10. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2749 of 3115

RS0VQ-01
H20950
RS-94
- SUPPLEMENTAL RESTRAINT SYSTEMSEAT POSITION SENSOR ASSEMBLY
2369 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the seat position sensor assembly in-
volved in a collision when the airbag has deployed.
Never repair a sensor in order to reuse it.
1. INSTALL SEAT POSITION SENSOR ASSEMBLY
(a) Connect the connector.
(b) Install the seat position sensor assembly with a new bolt.
Part No.:
Bolt: 90119-06871
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure that the sensor assembly is installed with
the specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT ASSEMBLY (DRIVER SIDE)
(See page BO-1 17)
3. INSPECT SRS WARNING LIGHT (See page DI-692)