1998 TOYOTA LAND CRUISER warning light

2004 LAND CRUISER (EWD548U)
237 SRS
NOTICE: When inspecting or repairing the SRS, perform the operation in accordance with the following precautionary
instructions and the procedure and precautions in the Repair Manual for the applicable model year.

Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of information
when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting the battery.

Work must be started after 90 seconds from when the ignition switch is turned to the ºLOCKº position and the
negative (-) terminal cable is disconnected from the battery.
(The SRS is equipped with a back-up power source so that if work is started within 90 seconds from
disconnecting the negative (-) terminal cable of the battery, the SRS may be deployed.)

When the negative (-) terminal cable is disconnected from the battery, the memory of the clock and audio system will be
canceled. So before starting work, make a record of the contents memorized in the audio memory system. When work is
finished, reset the audio systems as they were before and adjust the clock. This vehicle has power tilt and power
telescopic steering, power seat and power outside rear view mirror which are all equipped with memory function.
However, it is not possible to make a record of the memory contents. So when the work is finished, it will be necessary
to explain this fact tot the customer, and ask the customer to adjust the features and reset the memory. To avoid erasing
the memory in each memory system, never use a back-up power supply from outside the vehicle.

Before repairs, remove the airbag sensor if shocks are likely to be applied to the sensor during repairs.

Do not expose the steering wheel pad, front passenger airbag assembly, side airbag assembly, curtain shield airbag
assembly, seat belt pretensioner, center airbag sensor assembly, front airbag sensor assembly or side airbag sensor
assembly directly to hot air or flames.

Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, front passenger airbag
assembly, side airbag assembly, curtain shield airbag assembly, seat belt pretensioner, center airbag sensor assembly,
front airbag sensor assembly and side airbag sensor assembly should be inspected.

Never use SRS parts from another vehicle. When replacing parts, replace them with new parts.

Never disassemble and repair the steering wheel pad, front passenger airbag assembly, side airbag assembly, curtain
shield airbag assembly, seat belt pretensioner, center airbag sensor assembly, front airbag sensor assembly or side
airbag sensor assembly in order to reuse it.

If the steering wheel pad, front passenger airbag assembly, side airbag assembly, curtain shield airbag assembly, seat
belt pretensioner, center airbag sensor assembly, front airbag sensor assembly or side airbag sensor assembly has
been dropped, or if there are cracks, dents or other defects in the case, bracket or connector, replace them with new
ones.

Use a volt/ohmmeter with high impedance (10 kW/V minimum) for troubleshooting the system's electrical circuits.

Information labels are attached to the periphery of the SRS components. Follow the instructions on the notices.

After work on the SRS is completed, perform the SRS warning light check.

If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the Repair
Manual.

2004 LAND CRUISER (EWD548U)
278Wireless Door Lock Control
In this system, the door control receiver receivers weak radio wave transmitted from the transmitter built-into the ignition key,
and outputs a signal to the body ECU. Accordingly, all the doors are can be locked and unlocked by remote control.
1. Normal Operation
*Lock operation
When the lock SW on the transmitter is pressed, all the doors are locked.
*Unlock operation
When the unlock SW on the transmitter is pressed once, only the driver door is unlocked. When the unlock SW is pressed
again within 3 seconds, all the doors are unlocked.
2. Auto Lock Function
When the door is not actually opened within 30 seconds after the door has been unlocked by the unlock SW on the
transmitter, all the doors are automatically locked. If any of the following conditions are detected, the wireless door lock does
not function.
*Any door is opened.
*The ignition key is inserted into the ignition SW.
*When the unlock detection SW of all the doors are locked.
3. Wireless Door Lock Stop Function
If any of the following conditions are detected, the wireless door lock does not function.
Lock operation
*When any door is open (Door courtesy SW on)
*The ignition key is inserted into the ignition SW (Unlock warning SW on)
*Ignition SW is on
Unlock operation
*Ignition SW is on
4. Visual Confirmation of Lock or Unlock
During lock operation, when the door control receiver receives a lock signal from the door unlock detection SW, the turn
signal light is flashed once. During unlock operation, when the door control receiver receives an unlock signal from the door
unlock detection SW, the turn signal light is flashed twice.
5. Panic Mode Function
When the panic SW on the transmitter is pressed, the door control receiver receives a signal and enters the panic mode.
The signal input into the theft deterrent ECU from the body ECU turns on the theft deterrent horn, and flashes the taillight
and headlight. When the panic SW or the unlock SW of the transmitter is pressed during the panic mode, the panic mode is
canceled, and the theft deterrent horn stops, and the taillight and headlight are turned off.
6. Repeat Function
If the lock detection signal in response to the output signal is not received after the door control receiver has output the lock
signal, the lock signal is output again.
D27 Door Control Receiver
5-Ground : Always approx. 12 volts
1-Ground : Always continuity
D21, D22, D23, D24 Door Unlock Detection SW Front LH, RH, Rear LH, RH
1-Ground : Always continuity
B4 Back Door Unlock Detection SW
1-Ground : Always continuity
System Outline
Service Hints

2004 LAND CRUISER (EWD548U)
321
When the ignition SW turned on, a signal is input to the combination meter and the center cluster integration panel (w/
navigation system) or the A/C control assembly (w/o navigation system). To determine whether the driver has fastened the
seat belt, a signal is input from the buckle SW LH to the combination meter. When the seat belt is not fastened, the seat belt
warning light in the combination meter blinks, and emits a warning sound.
In addition, the front passenger is recognized by a sensor (Seat belt warning occupant detection sensor) is installed in the
front passenger seat, and determines whether the seat belt is fastened. When not fastened, the signals from the seat belt
warning occupant detection sensor and the buckle SW RH is input to the center cluster integration panel (w/ navigation
system) or the A/C control assembly (w/o navigation system), and the passenger seat belt warning light blinks to warn the
passenger.
S8 Seat Belt Warning Occupant Detection Sensor
1-2 : Closed with passenger sit on the front passenger seat
: Parts Location
CodeSee PageCodeSee PageCodeSee Page
A45A70C12A70C2870
A47C70C14C70J1471
B574C15D70J2272
B674C25A70S874
B770C25B70
:Junction Block and Wire Harness Connector
CodeSee PageJunction Block and Wire Harness (Connector Location)
2D28Dash Wire and Cowl Side J/B LH (Left Kick Panel)2G28Dash Wire and Cowl Side J/B LH (Left Kick Panel)
2K28Floor No.1 Wire and Cowl Side J/B LH (Left Kick Panel)
2Q30Instrument Panel Integration Wire and Cowl Side J/B LH (Left Kick Panel)
3D40Dash Wire and Cowl Side J/B RH (Right Kick Panel)
3K40Floor No.2 Wire and Cowl Side J/B RH (Right Kick Panel)
3N43Dash Wire and Cowl Side J/B RH (Right Kick Panel)
3Q42Instrument Panel Integration Wire and Cowl Side J/B RH (Right Kick Panel)
:Connector Joining Wire Harness and Wire Harness
CodeSee PageJoining Wire Harness and Wire Harness (Connector Location)
IX182Instrument Panel Integration Wire and Engine Wire (Behind the Glove Box)
BM290Floor No.1 Wire and Front Seat LH Wire (Front Side Under the Driver's Seat)
BO290Floor No.2 Wire and Front Seat RH Wire (Front Side Under the Front Passenger's Seat)
BU188Floor No.1 Wire and Floor No.1 Wire (Near the Left Rear Suspension Support)
BV188Floor No.2 Wire and Floor No.2 Wire (Near the Right Rear Suspension Support)
:Ground Points
CodeSee PageGround Points Location
EC76Rear Bank of Right Cylinder Head
BJ86Under the Driver's Seat
BK86Front Side Under the Front Passenger's Seat
BM86Left Rear Side Quarter Panel
:Splice Points
CodeSee PageWire Harness with Splice PointsCodeSee PageWire Harness with Splice Points
B1188Floor No.1 Wire
System Outline
Service Hints

2004 LAND CRUISER (EWD548U)
93 SYSTEM CIRCUITS H
2004 LAND CRUISER
ELECTRICAL WIRING DIAGRAM
SYSTEM CIRCUITS
Page
Air Conditioning (Front) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
356
Air Conditioning (Rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
Auto Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Automatic Glare-Resistant EC Mirror with Compass . . . . . . . . . . . . . . . . . . . 304
Automatic Light Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Back-Up Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Center Differential Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Cigarette Lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Combination Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Door Lock Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Electronically Controlled Transmission and A/T Indicator . . . . . . . . . . . . . . . 212
Engine Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Engine Immobiliser System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Front Wiper and Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Garage Door Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Interior Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Key Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
Light Auto Turn Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Mirror Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Moon Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Multi-Display (w/o Navigation System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
Multiplex Communication System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Multiplex Communication System (Communication Bus) . . . . . . . . . . . . . . . 168
Navigation System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Power Rear Quarter Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Power Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Power Tilt and Power Telescopic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
Power Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Radio and Player (w/ Navigation System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
Radio and Player (w/o Navigation System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
Rear Window Defogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
Rear Wiper and Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Remote Control Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Seat Belt Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Seat Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Shift Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
SRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Stop Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Taillight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Theft Deterrent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
TOYOTA Parking Assist (Rear View Monitor) . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Turn Signal and Hazard Warning Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
VSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Wireless Door Lock Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270

F04784Marks
- INTRODUCTIONFOR ALL OF VEHICLES
IN-1 1
11 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(3) Even in cases of a minor collision where the SRS
does not deploy, the steering wheel pad, front pas-
senger airbag assembly, side airbag assembly, cur-
tain shield airbag assembly and seat belt preten-
sioner should be inspected (See page RS- 18,
RS-32, RS-47, RS-60 and BO-143).
(4) Never use SRS parts from another vehicle. When
replacing parts, replace them with new parts.
(5) Before repairs, remove the airbag sensor if shocks
are likely to be applied to the sensor during repairs.
(6) Never disassemble and repair the airbag sensor as-
sembly, steering wheel pad, front passenger airbag
assembly, side airbag assembly, curtain shield air-
bag assembly or seat belt pretensioner in order to
reuse them.
(7) If the airbag sensor assembly, steering wheel pad,
front passenger airbag assembly, side airbag as-
sembly, curtain shield airbag assembly or seat belt
pretensioner have been dropped, or if there are
cracks, dents or other defects in the case, bracket
or connector, replace them with new ones.
(8) Do not directly expose the airbag sensor assembly,
steering wheel pad, front passenger airbag assem-
bly, side airbag assembly, curtain shield airbag as-
sembly or seat belt pretensioner to hot air or flames.
(9) Use a volt/ohmmeter with high impedance (10 kW/V
minimum) for troubleshooting of the electrical cir-
cuit.
(10) Information labels are attached to the periphery of
the SRS components. Follow the instructions on the
notices.
(11) After work on the supplemental restraint system is
completed, check the SRS warning light (See page
DI-692).
(c) SPIRAL CABLE (in Combination Switch)
The steering wheel must be fitted correctly to the steering
column with the spiral cable at the neutral position, other-
wise cable disconnection and other troubles may result.
Refer to SR-37 of this manual concerning correct steer-
ing wheel installation.

F02201N09214F05476
E1
DLC1
CG Ts
DLC3
Ts
B04696
Center Differential Lock
Indicator Light
Center Differential
Switch
Transfer Select
Lever
IN-18
- INTRODUCTIONFOR ALL OF VEHICLES
18 Author
: Date
:
2004 LAND CRUISER (RM1071U)
2. FOR VEHICLE EQUIPPED WITH VEHICLE SKID CON-
TROL (VSC) SYSTEM
(a) Precaution when using drum tester:
When using a drum tester, make sure that the ignition
switch is OFF, start the engine with the diagnosis connec-
tor short-circuited between Ts and E
1 (CG) and take a
measurement.
NOTICE:
Check that VSC warning light is blinking.
Ensure that the vehicle does not move using wires.
After the measurement, disconnect the short circuit
and check that the VSC warning light is turned off
when restarting the engine.
(b) Precaution during VSC operation:
(1) Since VSC may be affected by the removal/installa-
tion of the VSC-related parts, do not remove/install
those parts unless absolutely necessary.
(2) When operating on VSC, follow the instructions in
BR section in this manual to surely make prepara-
tions or check after operations.
3. WHEN SERVICING FULL-TIME 4WD VEHICLES
The Full-time 4WD LAND CRUISER is equipped with the me-
chanical lock type center differential system.
During tests using a brake tester or chassis dynamometer, such
as braking force tests or speedometer tests, if only the front or
rear wheels are to be rotated, it is necessary to set the position
of the center differential to FREE or LOCK depending on the
type of the test being performed.

B04201
B04202
- INTRODUCTIONFOR ALL OF VEHICLES
IN-21
21 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Using Braking Tester:
Measure by low-speed type (Vehicle Speed: Below 0.5
km/h or 0.3 mph) brake tester and observe the following
instructions before performing the test.
(1) Position the wheels to be tested (front or rear) on
the tester.
(2) Put the center differential in FREE position.
(3) If the vehicle is equipped with Vehicle Skid Control
(VSC) system, prohibit the system from the activa-
tion (See step 2.).
(4) Shift the transmission shift lever to ºNº position.
HINT:
Do not forget to change the Vehicle Skid Control (VSC) & Trac-
tion Control (TRAC) system to operational condition after the
test. Check that the VSC warning indicator light goes off when
restarting the engine.
(c) Using Speedometer Tester:
Observe the following instructions and then measure with
the rear wheels.
(1) Position the rear wheels on the tester roller.
(2) Position the front wheels on the free roller or jack
them up.
(3) Put the center differential in FREE position.
(4) If the vehicle is equipped with Vehicle Skid Control
(VSC) & Traction Control (TRAC) system, prohibit
the system from the activation (See step 2.).
(5) Ensure that the vehicle does not move using wires.
CAUTION:
The maximum speed should be less than 60 km/h (37 mph)
and maximum driving time should be 1 minute.
HINT:
Sudden shifting, braking, acceleration or deceleration is
not allowed.
Do not forget to change the Vehicle Skid Control (VSC) &
Traction Control (TRAC) system to operational condition
after the test. Check that the VSC warning indicator light
goes off when restarting the engine.

B04203
B04204
IN-22
- INTRODUCTIONFOR ALL OF VEHICLES
22 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(d) Using Chassis Dynamometer:
Observe the following instructions and then measure with
the rear wheels.
(1) Remove the front propeller shaft.
(2) Put the center differential in LOCK position.
(3) If the vehicle is equipped with Vehicle Skid Control
(VSC) & Traction Control (TRAC) system, prohibit
the system from the activation (See step 2.).
(4) Ensure that the vehicle is securely fixed.
HINT:
Sudden shifting, braking, acceleration or deceleration is
not allowed.
Do not forget to change the Vehicle Skid Control (VSC) &
Traction Control (TRAC) system to operational condition
after the test. Check that the VSC warning indicator light
goes off when restarting the engine.
(e) On-V ehicle Wheel Balancing:
When doing on-vehicle wheel balancing on a full-time
4WD vehicle, to prevent each wheel from being rotated at
different speed in different directions (which could dam-
age the center differential), always be sure to observe the
following precautions.
(1) All of 4 wheels should be jacked up, being apart
from the ground completely.
(2) Put the center differential in LOCK position.
(3) If the vehicle is equipped with Vehicle Skid Control
(VSC) & Traction Control (TRAC) system, prohibit
the system from the activation (See step 2.).
(4) The parking brake lever should be fully released.
(5) None of the brakes should be applied.
(6) The wheels should be driven on the wheel balancer
with the engine running.
(7) Carry out the wheel balancing with the transmission
position in D position.
HINT:
When doing this balancing, pay attention to the other
wheels rotating at the same time.
Sudden acceleration, deceleration or braking is not al-
lowed.
Do not forget to change the Vehicle Skid Control (VSC) &
Traction Control (TRAC) system to operational condition
after the test. Check that the VSC warning indicator light
goes off when restarting the engine.