B04933
New Gasket
B04934
Fulcrum
Length
30 cm
SST
B04895
SST Fulcrum
Length
30 cm
B02714
CORRECT
WRONG
Delivery Pipe O-Ring
- SFISFI SYSTEM
SF-3
1702 Author: Date:
2004 LAND CRUISER (RM1071U)
(b) When connecting the union bolt (fuel pressure pulsation
damper) on the high pressure pipe union, follow the pro-
cedure below:
(1) Always use 2 new gaskets.
(2) Tighten the union bolt by hand.
(3) Using SST, tighten the union bolt to the specified
torque.
SST 09612-24014 (09617-24011)
Torque:
33 N´m (340 kgf´cm, 24 ft´lbf) for use with SST
39 N´m (400 kgf´cm, 29 ft´lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(c) When connecting the flare nut on the high pressure pipe
union, follow the procedure below:
(1) Apply a light coat of engine oil to the flare nut, and
tighten the flare nut by hand.
(2) Using SST, tighten the flare nut to the specified
torque.
SST 09023-12700
NOTICE:
Do not rotate the fuel filter outlet when tightening the flare
nut.
Torque:
34 N´m (345 kgf´cm, 25 ft´lbf) for use with SST
38 N´m (380 kgf´cm, 28 ft´lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(d) Take following precautions to remove and install the injec-
tors.
(1) Never reuse the O-ring.
(2) When placing a new O-ring on the injector, take
care not to damage it.
(3) Coat a new O-ring with spindle oil or gasoline be-
fore installing; never use engine, gear or brake oil.
B04892
Fuel Return Hose
Pinch
SF-6
- SFISFI SYSTEM
1705 Author: Date:
2004 LAND CRUISER (RM1071U)
(6) Pinch the fuel return hose.
The pressure in the high pressure line will rise to
approx. 392 kPa (4 kgf/cm
2, 57 psi). In this state,
check to see that there is no leak on any part of the
fuel system.
NOTICE:
Always pinch the hose. Do not bend as it may cause the
hose to crack.
(7) Turn the ignition switch OFF.
(8) Disconnect the TOYOTA hand-held tester from the
DLC3.
SF0PQ-10
B16452
13
Voltmeter
B09192
2
3Voltmeter SF-52
- SFIVAPOR PRESSURE SENSOR
1751 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT POWER SOURCE VOLTAGE OF VAPOR
PRESSURE SENSOR
(a) Disconnect the vapor pressure sensor connector.
(b) Turn the ignition switch ON.
(c) Using a voltmeter, measure the voltage between connec-
tor terminal 1 and 3 of the wiring harness side.
Voltage: 4.5 - 5.5 V
(d) Turn the ignition switch OFF.
(e) Reconnect the vapor pressure sensor connector.
2. INSPECT POWER OUTPUT OF VAPOR PRESSURE
SENSOR
(a) Turn the ignition switch ON.
(b) Remove the fuel tank cap.
(c) Connect a voltmeter to terminal 2 and 3, and measure the
output voltage.
Voltage: 3.0 - 3.6 V
(d) Reinstall the fuel tank cap.
(e) Turn the ignition switch OFF.
