1998 TOYOTA 4RUNNER lights

4RUNNER (1998)
TRAILER TOWING TIPS
When towing a trailer, your vehicle
will handle differently than when
not towing. The three main causes
of vehicle- trailer accidents are driv-
er error, excessive speed and im-
proper trailer loading. Keep these in
mind when towing:
Before starting out, check operation
of the lights and all vehicle- trailer
connections. After driving a short
distance, stop and recheck the
lights and connections. Before ac-
tually towing a trailer, practice turn-
ing, stopping and backing with a
trailer in an area away from traffic
until you learn the feel.
Backing with a trailer is difficult
and requires practice. Grip the bot-
tom of the steering wheel and
move your hand to the left to move
the trailer to the left. Move your
hand to the right to move the trail-
er to the right. (This procedure is
generally opposite to that when
backing without a trailer). Also, just
turn the steering wheel a little at
a time, avoiding sharp or prolonged
turning. Have someone guide you
when backing to reduce the risk of
an accident.
Because stopping distance may be
increased, vehicle- to- vehicle dis-
tance should be increased when
towing a trailer. For each 16 km/h
(10 mph) of speed, allow at least
one vehicle and trailer length bet-
ween you and the vehicle ahead.
Avoid sudden braking as you may
skid, resulting in jackknifing and
loss of control. This is especially
true on wet or slippery surfaces.
Avoid jerky starts or sudden accel-
eration. If your vehicle has a
manual transmission, prevent ex-
cessive clutch slippage by keeping
engine rpm low and not racing the
engine. Always start out in first
gear.
Avoid jerky steering and sharp
turns. The trailer could hit your ve-
hicle in a tight turn. Slow down
before making a turn to avoid the
necessity of sudden braking.
Remember that when making a
turn, the trailer wheels will be clos-
er than the vehicle wheels to the
inside of the turn. Therefore, com-
pensate for this by making a larger
than normal turning radius with y-
our vehicle.
Crosswinds and rough roads will
adversely affect handling of your
vehicle and trailer, causing sway.
Pay attention to the rear from time
to time to prepare yourself for be-
ing passed by large trucks or
buses, which may cause your ve-
hicle and trailer to sway. If swaying
happens, firmly grip the steering
wheel and reduce speed immedi-
ately but gradually. Never increase
speed. Steer straight ahead. If you
make no extreme correction with
the steering or brakes, the vehicle
and trailer will stabilize.
Be careful when passing other ve-
hicles. Passing requires consider-
able distance. After passing a ve-
hicle, do not forget the length of
your trailer and be sure you have
plenty of room before changing
lanes.
In order to maintain engine braking
efficiency, do not use fifth gear
(manual transmission) or overdrive
(automatic transmission).

4RUNNER (1998)
Slow down and downshift be-
fore descending steep or long
downhill grades. Do not make
sudden downshifts.
Avoid holding the brake pedal
down too long or too frequent-
ly. This could cause the brakes
to overheat and result in re-
duced braking efficiency.Getting more kilometers/mileage from
a liter/gallon of fuel is easyÐjust take
it easy. It will help make your vehicle
last longer, too. Here are some specif-
ic tips on how to save money on both
fuel and repairs:
Keep your tires inflated at the
correct pressure. Underinflation
causes tire wear and wastes fuel.
See Chapter 7- 2 for instructions.
Do not carry unneeded weight in
your vehicle. Excess weight puts
a heavier load on the engine, caus-
ing greater fuel consumption.
Avoid lengthy warm- up idling.
Once the engine is running smooth-
ly, begin drivingÐbut gently. Re-
member, however, that on cold win-
ter days this may take a little
longer.
Accelerate slowly and smoothly.
Avoid jackrabbit starts. Get into
high gear as quickly as possible.
Avoid long engine idling. If you
have a long wait and you are not
in traffic, it is better to turn off the
engine and start again later.
Avoid engine lug or overrevving.
Use a gear position suitable for the
road on which you are travelling.
Avoid continuous speeding up
and slowing down. Stop- and- go
driving wastes fuel.
Avoid unnecessary stopping and
braking. Maintain a steady pace.
Try to time the traffic signals so
you only need to stop as little as
possible or take advantage of
through streets to avoid traffic
lights. Keep a proper distance from
other vehicles to avoid sudden
braking. This will also reduce wear
on your brakes.
Avoid heavy traffic or traffic
jams whenever possible.
Do not rest your foot on the
clutch or brake pedal. This
causes needless wear, overheating
and poor fuel economy.
Maintain a moderate speed on
highways. The faster you drive,
the greater the fuel consumption.
By reducing your speed, you will
cut down on fuel consumption.
Keep the front wheels in proper
alignment. Avoid hitting the curb
and slow down on rough roads.
Improper alignment not only causes
faster tire wear but also puts an
extra load on the engine, which, in
turn, wastes fuel.
How to save fuel and make
your vehicle last longer, to
o

4RUNNER (1998)
JUMP STARTING PROCEDURE
1. If the booster battery is installed in another vehicle, make sure the ve-
hicles are not touching. Turn off all
unnecessary lights and accesso-
ries.
2. If required, remove all the vent plugs from the booster and dis-
charged batteries. Lay a cloth over
the open vents on the batteries.
(This helps reduce the explosion
hazard, personal injuries and
burns.)
3. If the engine in the vehicle with the booster battery is not running, start
it and let it run for a few minutes.
During jump starting run the engine
at about 2000 rpm with the accel-
erator pedal lightly depressed.

4RUNNER (1998)
CAUTION
When making the connections, to
avoid serious injury, do not lean
over the battery or accidentally
let the jumper cables or clamps
touch anything except the correct
battery terminals or the ground.
5. Start your engine in the normal
way. After starting, run it at about
2000 rpm for several minutes with
the accelerator pedal lightly de-
pressed.
6. Carefully disconnect the cables in the exact reverse order: the nega-
tive cable and then the positive
cable.
7. Carefully dispose of the battery cover clothsÐthey may now con-
tain sulfuric acid.
8. If removed, replace all the battery vent plugs.
If the cause of your battery discharg-
ing is not apparent (for example,
lights left on), you should have it
checked. If your engine stalls while driving...
1. Reduce your speed gradually, keep- ing a straight line. Move cautiously
off the road to a safe place.
2. Turn on your emergency flashers.
3. Try starting the engine again.
If the engine will not start, see ºIf
your vehicle will not startº.
CAUTION
If the engine is not running, the
power assist for the brakes and
steering will not work so steering
and braking will be much harder
than usual.
If your vehicle overheats
If your engine coolant temperature
gauge indicates overheating, if you
experience a loss of power, or if
you hear a loud knocking or ping-
ing noise, the engine has probably
overheated. You should follow this
procedure... 1. Pull safely off the road, stop the vehicle and turn on your emergen-
cy flashers. Put the transmission in
ºPº (automatic) or neutral (manual)
and apply the parking brake. Turn
off the air conditioning if it is being
used.
2. If coolant or steam is boiling out of the radiator or reservoir, stop the
engine. Wait until the steam sub-
sides before opening the hood. If
there is no coolant boiling over or
steam, leave the engine running.
CAUTION
To help avoid personal injury,
keep the hood closed until there
is no steam. Escaping steam or
coolant is a sign of very high
pressure.
If your engine stalls while
driving

4RUNNER (1998)
Tire surface and wheel nuts
Check the tires carefully for cuts,
damage or excessive wear. See Chap-
ter 7- 2 for additional information.
When checking the tires, make sure
no nuts are missing, and check the
nuts for looseness. Tighten them if
necessary.
Tire rotation
Rotate the tires every 12000 km (7500
miles). See Chapter 7- 2 for additional
information.
Fluid leaks
Check underneath for leaking fuel, oil,
water or other fluid after the vehicle
has been parked for a while. If you
smell fuel fumes or notice any leak,
have the cause found and corrected
immediately.
Doors and engine hood
Check that all doors including back
door operate smoothly and all latches
lock securely. Make sure the engine
hood secondary latch secures the
hood from opening when the primary
latch is released. INSIDE THE VEHICLE
Items listed below should be
checked regularly, e.g. while per-
forming periodic services, cleaning
the vehicle, etc.
Lights
Make sure the headlights, stop lights,
tail lights, turn signal lights, and other
lights are all working. Check headlight
aim.
Service reminder indicators and
warning buzzers
Check that all service reminder indica-
tors and warning buzzers function
properly.
Steering wheel
Check that it has the specified free-
play. Be alert for changes in steering
condition, such as hard steering or
strange noise.
Seats
Check that all seat controls such as
seat adjusters, seatback recliner, etc.
operate smoothly and that all latches
lock securely in any position. Check
that the head restraint move up and
down smoothly and that the locks hold
securely in any latched position. For
folding- down rear seatbacks, swing- up
rear seat cushions and detachable
temporary third seat, check that the
latches lock securely.Seat belts
Check that the seat belt system such
as buckles, retractors and anchors op-
erate properly and smoothly. Make
sure the belt webbing is not cut,
frayed, worn or damaged.
Accelerator pedal
Check the pedal for smooth operation
and uneven pedal effort or catching.
Clutch pedal
Check the pedal for smooth operation.
Brake pedal
Check the pedal for smooth operation
and that the pedal has the proper
clearance. Check the brake booster
function.
Brakes
At a safe place, check that the brakes
do not pull to one side when applied.
Parking brake
Check that the lever has the proper
travel and that, on a safe incline, your
vehicle is held securely with only the
parking brake applied.

4RUNNER (1998)
If the headlights or other electrical
components do not work, check the
fuses. If any of the fuses are blown,
they must be replaced.
See ºFuse locationsº in Chapter 7- 1
for locations of the fuses.
Turn the ignition switch and inop-
erative component off. Pull a sus-
pected fuse straight out and check it.
Determine which fuse may be causing
the problem. The lid of the fuse box
shows the name of the circuit for
each fuse. See Part 8 of this manual
for the functions controlled by each
circuit. Type A fuses can be pulled out by
using the pull- out tool. The location of
the pull- out tool is shown in the il-
lustration.
If you are not sure whether the fuse
has blown, try replacing the suspected
fuse with one that you know is good.
If the fuse has blown, push a new
fuse into the clip.
Only install a fuse with the amperage
rating designated on the fuse box lid.
If you do not have a spare fuse, in
an emergency you can pull out the
ºDOMEº or ºA/Cº fuse, which may be
dispensable for normal driving, and
use it if its amperage rating is the
same.If you cannot use one of the same
amperage, use one that is lower, but
as close as possible to the rating. If
the amperage is lower than that speci-
fied, the fuse might blow out again but
this does not indicate anything wrong.
Be sure to get the correct fuse as
soon as possible and return the sub-
stitute to its original clip.
It is a good idea to purchase a set
of spare fuses and keep them in your
vehicle for emergencies.

4RUNNER (1998)
Light bulbs
Bulb No.WTy p e
Headlight'60/5 5A
Parking and front side
marker lights'5C
Front turn signal lights115627B
Rear turn signal lights'21C
Stop and tail lights'21/5C
Back- up lights'21C
License plate lightÐ5C
High mounted
stop light92118C
Interior lightÐ8D
Personal lightsÐ8D
Glovebox lightÐ1.4C
Luggage compartment
lightÐ8D
A: HB2 halogen bulbs
B: Single end bulbs
C: Wedge base bulbs
D: Double end bulbs ÐHeadlights

4RUNNER (1998)
2. Release the bulb retaining spring and remove the bulb. Install a
new bulb and the bulb retaining
spring.
To install a bulb, align the tabs of the
bulb with the cutouts of the mounting
hole.
3. Install the rubber cover, and snuggle on the boss. Insert the
connector.
Make sure the rubber cover fits snug-
ly on the connector and the headlight
body.
Aiming is not necessary after replac-
ing the bulb. When aiming adjustment
is necessary, contact your Toyota
dealer. ÐParking and front side ma
r
er lights